Laserfiche WebLink
13 SIGN COMPONENTS MANUAL (SAM)June 19, 2013 <br />5. Grounding of frame to supply ground is required. Suitability of bonding for grounding connection is to be determined in final <br />application. <br />6. Suitability of LED panel mounting shall be determined in final application. <br />7. Suitability of LED power source shall be determined in the final application. <br />Polymeric adhesive systems, Cat Nos. DP-810 and DP-810 Black designated "Scotch-Weld" <br />1. The use of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not <br />exceeded. <br />2. These systems may be used for securement to any combination of surfaces Listed in Table A, provided the use of <br />temperature is no higher than the lowest temperature rating of any element of the combination <br />3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been <br />performed on the adhesive by itself. The Engineer must consider the need to investigate the part of other than the properties <br />investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for <br />Polymeric Materials - Use in Electrical Equipment Evaluations, UL 746C. <br />4. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been <br />determined. <br />5. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to <br />another surface or configuration shall be determined in the particular end use application. <br />6. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The <br />minimum temperature rating is -35°C (-31°F). <br />7. The adhesive shall be applied in accordance with the manufacturer''s instruction. All surfaces shall be clean and dry. The <br />manufacturer's instructions regarding cure time shall be followed. <br />8. The adhesive bond strength specified in Table A includes a safety factor of four. <br />9. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts <br />shall be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the <br />bond strength and includes static load as well as wind loading(dynamic load). The minimum square inches of adhesive to use <br />is determined by dividing the maximum load in pounds by the adhesive bond strength specified in Table A. <br />TABLE A <br />Cat. Nos.DP-810, DP-810 Black Thickness: 0.076 mm (0.003 in) <br />Substrate Combination Max. Operating Temp.Adhesive Bond <br />°C (°F)Strength(PSI) <br />Stainless Steel to Stainless Steel 60 1000 <br />Aluminum to Aluminum 60 980 <br />Polycarbonate to Polycarbonate 60 180 <br />Magnesium to Magnesium 60 870 <br />Acrylonitrile Butadiene Styrene to Acrylonitrile 60 310 <br />Butadiene Styrene <br />Cat. Nos.DP-810, DP-810 Black Thickness: 0.254 mm (0.010 in) <br />Substrate Combination Max. Operating Temp.Adhesive Bond Strength <br />°C (°F)(PSI) <br />Stainless Steel to Stainless Steel 60 940 <br />Aluminum to Aluminum 60 900 <br />Polycarbonate to Polycarbonate 60 190 <br />Magnesium to Magnesium 60 690 <br />Acrylonitrile Butadiene Styrene to Acrylonitrile 60 430 <br />Butadiene Styrene <br />AA LED SUPPLY CORP E325964 <br />9441 VALLEY BLVD. <br />ROSEMEAD, CA 91770 <br />Class 2 LED modules, Models LS0723x, LS0766x, LS0769x, LS0776x, where that x may be R, G, B or Y indicating LED Color. <br />1. These products are only suitable for connection to the output of a UL Listed or FUC Class 2 Power Supply rated 12VDC. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 <br />requirements. <br />3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to <br />draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. <br />Part No.Operating Current per Watts per module <br />Voltage module <br />LS0723x 12Vdc 40mA 0.48W <br />LS0766x 12Vdc 30mA 0.36W <br />LS1769x 12Vdc 75mA 0.90W <br />LS0776x 12Vdc 60mA 0.72W