10179885_1247 S. MAIN - Plan - Laserfiche WebLink

Home Browse Search

135 SIGN COMPONENTS MANUAL (SAM)October 1,2013 2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacihg to top of enclosure. 4. These products are provided with the following electrical ratings: Input Output |Model Vac A Hz Vdc A 701680-MW | 100-240 055 50/60 12 1.67 5. These products shall be enclosed in the end product. 6. These power supplies are suitable for use in dry and damp locations. Class 2 power supply, Model 701681. 1. The product shall be installed in compliance'with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015. No. 18 AWG, rated VW-1,600 V. 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300 V. 105°C. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame classj of the polymeric enclosure is V-0 and the necessity of additional fire barriers shall be determined in end product. 7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power supplies, Model 701495. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of four Class 2 outputs. 2. These power supplies are only suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing t0 sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power LED Lighting Strip, 701912-QQXXYYZZZ series, where QQ represents length, XX represents the LED color temperature, YY represents configuration and ZZZ represents the LED drive current. 1. These products are only suitable for connection to a Class 2 power source, rated 24VDC. 2- These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage; and energy limits and which is rated greater than 24VDC. 3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or Outline lighting, the need te conduct a temperature test shall be considered. Class 2 "Dimming Control Knob" potentiometer, Model 701843. 1. These products afe only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12 VDC. 2. These products are suitablefor use in dig, and damp locations. 3. These products are suitabla for factory wiring only. 4. These products are 1 Kohm potentiometers intended for connection to max 12 VDC Class 2 power supply that drops the voltage to a 0-10 V signal to feed into the PWIVI dimmer. Class 2 LED Modules, Cat. No. 701960-XXYYYZ Series, where XX, YYY, and Z maybe replaced with anyialpbanumeric character or blank. 1. These products are suitable for use in dry, damp and wet locations aAd supplied only with a Classj 2 power source rated, 24 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 power supplies, Models 701507-60W1-JV and 701507-60W1-CT. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. These products are provided with the following electrical ratings: Output Output Frequency Voltage Current Model Number Input Voltage (\4 Input.Current (A)(Hz):(\/dc)(mA) 701507-60W1-JV 100L240 0.85 50/60 12 0-500 70 1 507-60W1 -CT 3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in) from end to end and 101.6 mm (4 in) from side to side. 4. These products shall be enclosed in the end product. 5. These products are suitable for factor'y wiring only. 6. These products are intended for use in a dry or damp locationsonly. 7. The suitability of input/output leads and the wring shall be determined in end product use. SPARTECH PLASTICS E202184