Laserfiche WebLink
GENERAL NOTES AND SPECIFICATIONS: m <br />1), THE FOAM CORE ROOF PANELS DEPICTED WITHIN THIS DRAWING ARE INTENDED FOR USE ON <br />RESIDENTIAL PAnOS AS REGULATED BY APPENDIX I OF THE 2010 CALIFORNIA BUILDING CODE, <br />APPENDIX H OF THE 2010 CALIFORNIA RESIDENTIAL CODE OR ON MOBILE HOME AWNINGS AS <br />REGULATED BY TITLE 25 OF THE CALIFORNIA ADMINISTRATIVE CODE. <br />2) MATERIALS: <br />a) INTERIOR FACING MATERIAL SHALL BE ALUMINUM CONFORMING TO THE REQUIREMENTS <br />FOR 3105-H26 ALLOY AND TEMPER. THICKNESS OF SKIN SHALL BE AS SHOWN IN THE <br />APPROPRIATE ALLOWABLE SPAN TABLE. THE UNEXPOSED SIDE OF THE INTERIOR METAL 4'-0" <br />SKIN SHALL HAVE A BONDING MATERIAL COMPATIBLE WITH THE ADHESIVE DEFINED IN NOMINAL <br />2d. PAINT ON OUTSIDE SURFACE OF METAL SKIN SHALL BE POLYESTER AS SPECIFIED IN .///9//<THE QUALITY CONTROL SYSTEMS MANUAL.\\ <br />b) EXTERIOR FACING MATERIAL SHALL BE ALUMINUM CONFORMING TO THE REQUIREMENTS <r <br />FOR 3105+126 ALLOY AND TEMPER. ™ICKNESS OF SKIN SHALL BE AS SHOWN IN THE p.. <br />APPROPRIATE ALLOWABLE SPAN TABLE. THE UNEXPOSED SIDE OF THE EXTERIOR METAL <br />SKIN SHALL HAVE A BONDING MATERIAL COMPATIBLE WITH THE ADHESIVE DEFINED IN <br />2d. PAINT ON OUTSIDE SURFACE OF METAL SKIN SHALL BE POLYESTER AS SPECIFIED IN <br />THE QUALITY CONTROL SYSTEMS MANUAL. <br />-THICKNESS <br />(SEE ALLOWABLEc) THE FOAM CORE SHALL BE AS DEFINED BELOW AND HAVING A NOMINAL DENSITY AS <br />SHOWN IN THE ALLOWABLE SPAN TABLE:SPAN TABLE) <br />ADHESIVE <br />(NOTE 2d) -FOAM CORE <br />/ (NOTE 24 <br />EXTERIOR FACE <br />(NOTE 2b) <br />/ <br />ADHESIVE INTERIOR FACE <br />LENGTH <br />(NOTE 2d)(NOTE 2a) <br /> (SEE ALLOWABLE <br />\ SPAN TABLE) <br />I \\\ <br />\\ <br />\\\ <br />, SIM 1. 6.- \\\€ <br />·-mON -44 \ <br />0- u. <br />9 CEO 0 <br />" <br />3 <W E <br />Z <br />5u <br />0- <br />0< <br />of O. 2, <br />1) PREFORMED EXPANDED POLYSTYRENE BOARD (EPS), AS MANUFACTURED BY ONE <br />OF SEVERAL RECOGNIZED MANUFACTURERS SPECIFIED IN THE QUALITY SYSTEMS <br />MANUAL. THE FOAM SHALL MEET THE REQUIREMENTS FOR CLASS I MATERIAL PER <br />TABLE 8-A OF ™E 1997 UBC. THE FOAM PLASTIC IS CLASSIFIED AS TYPE I FOAM IN <br />ACCORDANCE WITH ASTM C578. <br />FAN BEAM --I <br />(OPTIONAL ON 4'-0" <br />WIDE PANEL) g <br />L U N O 1 < .0 <br />O 25PANEL INTERIOR DETAIL /Ah\ 3 2 <br />NTS - CO O <br />< LU <br />- EXTERIOR SKIN zk <br />t[--1 <br />ES <br />J1 <br />2% :0: 00%:000700 :f>0 00 0 <br />a :eptonlhajob: fly Chati&68 014 / ---L <br />4 ,:sion from thk17 HCD/CALIF <br />INSIGNIA <br />I¥PICAL ROOFARAINEL PANEL EDGE DETA16 <br />NTS NTS £.'ation of any <br />O <br />-- 0 <br />XE 2 <br />95 2 oi <br />0 <br />0502 <br />d) THE COMPONENTS ARE BONDED TOGETHER BY AN ADHESIVE DESIGNATED AS EITHER <br />MORAD M-650 SERIES, A PROPRIETARY ADHESIVE MANUFACTURED BY ROHM AND HAAS <br />COMPANY, AND RECOGNIZED UNDER ICC ES ESR-1023, OR ISOGRIP SP5050O, A <br />PROPRIETARY ADHESIVE MANUFACTURED BY ASHLAND SPECIALTY CHEMICAL COMPANY <br />AND RECOGNIZED UNDER ICC ES ESR-1140. THE ADHESIVE IS A CLASS 2, TYPE Il, <br />STRUCTURAL ADHESIVE, UNDER ICC ES AC05. <br />3) THE MANUFACTURER OF ANY COMPONENT CITED IN ITEM 2 ABOVE SHALL PROVIDE <br />CERTIFICATION WITH EACH SHIPMENT THAT ALL COMPONENTS PROVIDED WITHIN THE <br />SHIPMENT CONFORM TO THE APPLICABLE SPECIFICATION(S) AND/OR DEFINITION(S) OUTLINED <br />ABOVE. <br />4) THE MAXIMUM ALLOWABLE SPAN, FOR A GIVEN APPLIED LOAD SHALL NOT EXCEED THE SPAN <br />PROVIDED IN THE ALLOWABLE SPAN TABLE FOR SAID LOAD. <br />INTERIOR SKIN <br />2,3 -i C a *2%*: E X£209 <br />-FBH- 8 ___0117020 <br />13002 <br />0 <br />*a <br />1 9 2 1 <br />.waz <br />g <br />0 <br />E i <br />g: <br />t6 <br />EXTRAPOLATION OF THE INFORMATION PROVIDED IN THE ALLOWABLE SPAN TABLE IS NOT <br />PERMITTED. <br />5) PANELS SHALL BE CONTINUOUS IN THE DIRECTION OF SPAN WITH NO TRANSVERSE JOINTS. <br />6) THE SUPPORT AND STRUCTURAL ATTACHMENT OF THE SUBJECT PANELS SHALL BE <br />SUBSTANTIATED BY EITHER APPROVED EVALUAllON REPORT PLANS OR STRUCTURAL PLANS <br />APPROVED BY THE GOVERNING JURISDICTION. THE GOVERNING JURISDICTION SHALL CONFIRM <br />THAT SAID PLANS ARE INTENDED FOR USE WITH THE DESIRED PANEL LOADS AND SPANS FOR <br />EACH SPECIFIC PROJECT. <br />t=0.080 - <br />ALUM 6063-T5 \- <br />3.1\ <br />lilli O <br />00 4 0.0 I<24 ,-00 0 <br />, 0 0,0 <br />.00 <br />CL <br />PANEL .0 <br />1 4,0 <br />-O 0 0 <br />1%009. <br />do o o <br />ic·5·. <br />0 <br />0. <br />1% <br />41 L 0.0934- - 0.0934 <br />- - 0.08001.5000 <br />0.0800 - - <br />0 <br />7) ALL PANEL EDGES SHALL BE SHIELDED IN ALUMINUM SECTIONS. ALL INTERFACES BETWEEN UM** <br />THE ALUMINUM SECTIONS AND PANEL SHALL BE CAULKED WITH APPROPRIATE SEALANT..89.°040 .7,0 6.,0 .-L- <br />8) METAL PANEL FASTENERS SHALL BE STAINLESS STEEL OR ALUMINIZED, HOT-DIP GALVANIZED F .. 0 0 00 +004.000.1.:..8Coot·o o·°oooer:48°;ao-°·% 1°°0 <br />OR ELECTROGALVANIZED STEEL. <br />9) AN IDENTIFICATION DECAL WITH DEPARTMENT OF HOUSING INSIGNIA AND MANUFACTURER'S <br />IDENTIFICATION NUMBER SHALL BE LOCATED AT ONE END OF EACH PANEL. <br />10) FASTENERS SHALL BE #14 SELF-TAPPING SMS AND 1 O.D., SEAL WASHER WITH NEOPRENE <br />INSERT. THE FASTENER LENGTH WILL BE 1- LONGER THAN THE PANEL WIDTH. ALLOY AND <br />MINIMUM THICKNESS OF HEADER SHALL BE 6063-T6 AND 0.062 INCHES RESPECTIVELY.FAN BEAM DETAIL <br />11) 01 rfUL 1 Urltze INUL.UUCU v,fil r,11,1 inia raurv,oc or·,ALL. Ivul ec A i I tiuncu w 0,11•UL-C= L,v- <br />STUCCO SYSTEMS.NTS <br />12)SNOW LOADS PRESENTED WITHIN THESE PLANS ARE "EQUIVALENT- UNIFORM SNOW LOADS. <br />CONSIDERATION SHALL BE GIVEN TO SITE SPECIFIC CONDITIONS INCLUDING, BUT NOT LIMITED <br />TO, DRIFTING AND SLIDING SNOW. <br />----RO.0200 <br />S-J-U-U%-E-•+--e--'-r-E-%-A--2 -a 11* 13 53 5% 8 i 2Z 2L RO.0200 OL g D.-M#De.k H3.5000 6< 12.fwIS:lfi o P fi oD. Z <br />Pi'&1122:% U z Cw E .8-0* O 1 >g gs/3·E 02&2.v = <br />/Ch &20 8 & 2.52 9 0 0 a <. 6 0 <br />a.£=6.-5 4 5 W & <br />UN **22 ul - E2-0 Ec »ca2 B. #20 4 2 X <br />.-2,4*-c O 0. 111 <br />4/13 TJC 6/12 TJC 3/11 TJC Afl 31vo <br />13) PLANS ARE CONSIDERED NULL AND VOID IF THEY DO NOT CONTAIN ORIGINAL SEAL AND <br />SIGNATURE (IN BLUE INK) BY THE ENGINEER OF RECORD (EOR) OR THE FACTORY BUILT <br />HOUSING APPROVAL STAMP.ECEIVE <br />14) PLANS HAVE BEEN TESTED IN ACCORDANCE WITH ASTM E108 AND HAVE BEEN DETERMINED TO <br />MEET THE CONDITIONS OF ACCEPTANCE FOR A -CLASS B- RATING. <br />15) UNLESS OTHERWISE NOTED, THE SCOPE OF THIS DRAWING PACKAGE IS LIMITED TO THE OCT 1 7 2013 <br />STRUCTURAL ASPECTS OF THE SUBJECT PANELS. NONSTRUCTURAL REQUIREMENTS OF THE <br />GOVERNING CODE AND LOCAL JURISDICTION SHALL BE ADDRESSED BY THE MANUFACTURER <br />AND/OR CONTRACTOR.City of Santa Ana <br />16) CONSIDERATION HAS BEEN GIVEN TO BE TO THE ADDITION OF ONE (1) CEILING FAN PER 4' WIDE <br />PANEL WITH A MAXIMUM FAN WEIGHT OF 50 POUNDS. THEREFORE, THE ALLOWABLE LOADS <br />PROVIDED ABOVE ARE IN ADDITION TO THE WEIGHT OF THE CEILING FAN. <br />VISIT WWW.TJCAA.COM/LINKS.HTML TO CONFIRM LATEST REVISION OF PLANS HAS BEEN SUBMITTED. PLAN # IS: 807008 CA-LRP-2410 <br />€102 8 0 AWN DATE SIGNED: <br />SS/0469 <br />V O <br />No.1 s <br />Lxp./13 X <br />Cl-09*2 F CAL\2. <br />U d. <br />00. <br />,*ve:La2* <br />V41[) IF NOT <br />WAT SIGNED WITH BLUE INK <br />V' .... <br />WET SIGNED DOCUMENT HAS. <br />EMBOSSED CORPORATE SEAL- / <br />3 <br />1 1 1 1 1 1 1 1 1