Laserfiche WebLink
Datasheet <br />SunPower®SunVault™ Hub+™ <br />Electrical <br />Model Number SV-HUB-01-B / SV-HUB-01-C <br />Applications Self-supply, backup, and cost savings <br />Special Features PCS, Remote Power Off <br />Supported Backup Configurations x Whole home (up to 200 A service) <br />x Partial home (up to 400 A service) <br />Max. Allowed Service / Disconnect Rating 200 A <br />Nom. Allowed Service Voltage 120 / 240 V 60 Hz, split phase <br />Short Circuit Rating1 10 kA / 22 kA2 <br />Overcurrent Protection Device Allowed3 100–200 A / service entrance rated <br />AC Metering Solar meter: ANSI C12.20, < 0.5% RGM | Site meter: < 2% <br />Connectivity Ethernet, WiFi, and cellular <br />Backup Transition Seamless <br />Load / Generation Breakers4 Refer to installation guide for available spaces <br />Overvoltage Category OV IV <br />Pollution Degree III <br />Protection Class I <br />Scalability5 Supports multiple storage and PV systems in parallel <br />1 Higher short circuit rating is compatible with external suitable rated equipment. <br />2 With external J-Class fuse or CSR breaker. See the SunVault Installation Guide for <br />guidelines. <br />3 Recommended service-rated circuit breaker type must be installed. <br />4 See the SunVault Installation Guide for guidelines. <br />5 See the SunVault Installation Guide for guidelines. <br />Refer to www.sunpower.com/facts for additional reference information. <br />For more details, see extended datasheet www.sunpower.com/datasheets. Specifications <br />included in this datasheet are subject to change without notice. <br />©2022 SunPower Corporation. All Rights Reserved. SUNPOWER, the SUNPOWER logo, <br />SUNVAULT, and Hub+ are trademarks or registered trademarks of SunPower Corporation <br />in the U.S. and other countries as well. 1-800-SUNPOWER. <br /> Environmental <br />Ambient Operating <br />Temp. í4°F to 122°F (í20°C to 50°C) <br />Shelf Ambient <br />Temp. í22°F to 140°F (í30°C to 60°C) <br />Humidity 0–95% (non-condensing) <br />Enclosure Type / <br />Ingress Rating NEMA Type 3R / IP54 <br />Max. Elevation 6560 ft (2000 m) <br />Environment Indoor / Outdoor <br />Mechanical <br />Dimensions 17 w × 46 h × 6 in. d (43 × 117 × 15 cm) <br />Weight 80 lb (36 kg) <br />Mounting Options Indoor / Outdoor <br />Conduit Entry Multiple; up to 3 in. (7.6 cm) <br /> Warranties, Certifications, and Compliance <br />Warranty 10 years <br />Certifications <br />and <br />Compliance <br />x ANSI C12.20 (Class 0.5) <br />x CSA C22.2 No. 107.1 <br />x FCC Part 15 Subclass B <br />x UL 67 <br />x UL 869A <br />x UL 1741 <br />x UL 1741 CRD PCS <br /> 55 33 66 88 11 33 ReRe vv DD <br />AUTHORIZATION TO MARK <br />Applicant: <br />Address: <br />Country: <br />Manufacturer: <br />Address: <br />Country: <br />Syncro Corporation <br />1030 Sundown Drive NW <br />Arab, Alabama 35016 <br />USA 1265701 1 <br />Product: <br />Brand Name: <br />Models: <br />SunPower Corporation <br />51 Rio Robles <br />San Jose, CA 95134 <br />USA <br />Same as Manufacturer <br />Intertek Testing Services NA, Inc., Cortland, NY <br />Party Authorized To Apply Mark: <br />Report Issuing Office: <br />Control Number:5016932 Authorized by: <br />for L. Matthew Snyder, Certification Manager <br />This document supersedes all previous Authorizations to Mark for the noted Report Number. <br />This Authorization to Mark is for the exclusive use of Intertek's Client and is provided pursuant to the Certification agreement between Intertek and its Client. Intertek's responsibility and liability are <br />limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned <br />by the use of this Authorization to Mark. Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety. Use of Intertek’s Certification mark is <br />restricted to the conditions laid out in the agreement and in this Authorization to Mark. Any further use of the Intertek name for the sale or advertisement of the tested material, product or service must <br />first be approved in writing by Intertek. Initial Factory Assessments and Follow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the agreement, <br />they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect. <br />Intertek Testing Services NA Inc. <br />545 East Algonquin Road, Arlington Heights, IL 60005 <br />Telephone 800-345-3851 or 847-439-5667 Fax 312-283-1672 <br />Panelboard <br />EQS-HUB-01-A, SV-HUB-01-A, SV-HUB-01-B, SV-HUB-01-C <br />Standard(s): <br />Standard for Safety Panelboards [UL 67:2018 Ed.13+R:31Jul2020] <br />Reference Standard for Service Equipment [UL 869A:2006 Ed.4+R:24Jun2020] <br />Inverters, Converters, Controllers And Interconnection System Equipment For Use With Distributed <br />Energy Resources [UL 1741:2010 Ed.2+R:15Feb2018] <br />Power Conversion Equipment [CSA C22.2#107.1:2016 Ed.4] <br />SUNPOWER <br />This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s) <br />Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing <br />Report. This authorization also applies to multiple listee model(s) identified on the correlation page of the Listing <br />Report. <br />This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may <br />y: <br />f L M tth S d C tifi ti M <br />Page 1 of 1 ATM for Report 104106139CRT-001 ATM Issued: 26-Jul-2022 <br />ED 16.3.15 (1-Jul-2022) Mandatory <br />1402 W Meriday Ln - <br />201816051/10/2024