Laserfiche WebLink
MODULES <br />REF.QTY. MAKE AND MODEL PMAX (W) PTC(W) ISC IMP VOC VMP TEMP. COEFF. OF VOC FUSE RATING <br />PM1-40 40 APTOS SOLAR TECHNOLOGY LLC, DNA-108-BF10-400W 400 373 13.79A 12.9A 37.1V 31V -0.12V/°C (-0.27%/°C)20A <br />DISCONNECTS <br />REF. QTY.MAKE AND MODEL RATED CURRENT (A)MAX RATED VOLTAGE <br />SW1 1 SQUARE D D223NRB OR EQUIV.100 240VAC <br />INVERTERS <br />REF. QTY. MAKE AND MODEL AC VOLTAGE GROUND MAX OCPD RATING MAX CONTINUOUS <br />OUTPUT POWER (W)MAX OUTPUT CURRENT MAX INPUT CURRENT MAX INPUT VOLTAGE CEC WEIGHTED EFFICIENCY <br />I1-40 40 ENPHASE IQ8A-72-2-US 240V NOT SOLIDLY GROUNDED 20A 349 1.45 20A 60V 97% <br />PASS-THRU BOXES AND COMBINERS <br />REF.QTY.MAKE AND MODEL RATED CURRENT MAX RATED VOLTAGE <br />C1 1 ENPHASE X2-IQ-AM1-240-4 OR EQUIVALENT (AC COMBINER WITH GATEWAY)65A 240VAC <br />MICRO- <br />INVERTER <br />I1-40 <br />10 IN <br />BRANCH <br />10 IN <br />BRANCH 1 2 <br />3 4 <br />5 6 <br />7 <br />AC COMBINER <br />C1 <br />2 <br />PV DISCONNECT <br />SW1 <br />100A 39 <br />MAIN SERVICE PANEL <br />AC <br />GEC <br />KWHRKWHR UTILITY METER <br />(N) 175A MCB WITH 225A BUSBAR <br />(N) 175A <br />10 11 <br />NOTES <br />1 <br />2 <br />3 <br />4 <br />5 <br />6 <br />7 <br />9 <br />10 <br />11 <br />LOADS <br />LOADS <br />CONDUCTOR AND CONDUIT SCHEDULE W/ELECTRICAL CALCULATIONS <br />ID TYPICAL CONDUCTOR CONDUIT / CABLE <br />CURRENT-CARRYING <br />CONDUCTORS IN CONDUIT / <br />CABLE <br />OCPD (A)EGC TEMP. CORR. <br />FACTOR <br />FILL <br />FACTOR <br />CONT. <br />CURRENT (A) <br />MAX. <br />CURRENT <br />(125%) <br />BASE AMP.DERATED <br />AMP. <br />TERM. <br />TEMP. <br />RATING <br />AMP. @ TERM. <br />TEMP. RATING <br />LENGTH <br />(FT)RESISTANCE/FT VOLTAGE <br />DROP <br />1 1 10 AWG THWN-2, COPPER 0.75" EMT 8 N/A 6 AWG THWN-2, COPPER 0.58 61°C 1.0 14.5 18.1 40 23.20 75°C 35 30 0.0003951 0.09% <br />2 1 3 AWG THWN-2, COPPER 1" EMT 3 80A 8 AWG THWN-2, COPPER 0.91 39°C 1.0 58.0 72.50 110 100.10 75°C 100 6 0.0019700 0.34% <br />3 1 3 AWG THWN-2, COPPER 1" EMT 3 80A 8 AWG THWN-2, COPPER 0.91 39°C 1.0 58.0 72.50 110 100.10 75°C 100 6 0.0019700 0.34% <br />PV MODULE <br />PM1-40 <br />400W <br />11 <br />CB1 <br />20A <br />CB2 <br />20A <br />CB3 <br />20A <br />10 IN <br />BRANCH <br />SYSTEM SUMMARY <br />BRANCH 1 BRANCH 2 BRANCH 3 BRANCH 4 <br />INVERTERS PER BRANCH 10 10 10 10 <br />MAX AC CURRENT (A)14.5 14.5 14.5 14.5 <br />MAX AC POWER OUTPUT (W)3480 3480 3480 3480 <br />ARRAY STC POWER (W)16000 <br />ARRAY PTC POWER (W)14920 <br />MAX AC CURRENT (A)58 <br />MAX AC POWER OUTPUT (W)13920 <br />1 <br />CB4 <br />80A <br />8 <br />8 <br />CB4 <br />20A <br />10 IN <br />BRANCH <br />LOADS <br />12 <br />12 <br />FUSES 80A <br />SPD <br />Square D <br />HEPD80 <br />20A <br />E1.0 <br />REVISIONS <br />DOC ID: <br />PROJECT <br />SUMMARY <br />GR <br />I <br />D <br />- <br />T <br />IE <br />D <br /> <br />S <br />O <br />L <br />A <br />R <br /> <br />P <br />O <br />W <br />E <br />R <br /> <br />S <br />Y <br />ST <br />EM <br />SSPR-013 <br />94 <br />1 <br /> <br />W <br />E <br />S <br />T <br /> A <br />L <br />T <br />ON <br /> <br />A <br />V <br />E <br />N <br />U <br />E <br />, <br />DATE: 03/22/23 <br />CONTRACTOR: PAUL NAKHLE <br />COMPANY: SOLECTRIC SOLUTION <br />SA <br />N <br />T <br />A <br />A <br />N <br />A <br />, <br /> <br />C <br />A <br /> <br />9 <br />2 <br />7 <br />0 <br />7 <br />GENERAL ELECTRICAL NOTES <br />1 <br />UTILITY HAS 24-HR UNRESTRICTED ACCESS TO ALL <br />PHOTOVOLTAIC SYSTEM COMPONENTS LOCATED AT <br />THE SERVICE ENTRANCE. <br />2 <br />CONDUCTORS EXPOSED TO SUNLIGHT SHALL BE LISTED <br />AS SUNLIGHT RESISTANT PER NEC ARTICLE 300.6 (C) (1) <br />AND ARTICLE 310.10 (D). <br />3 <br />CONDUCTORS EXPOSED TO WET LOCATIONS SHALL BE <br />SUITABLE FOR USE IN WET LOCATIONS PER NEC <br />ARTICLE 310.10 (C). <br />GROUNDING NOTES <br />1 ALL EQUIPEMENT SHALL BE PROPERLY GROUNDED PER <br />THE REQUIREMENTS OF NEC ARTICLE 250 AND 690 <br />2 <br />PV MODULES SHALL BE GROUNDED TO MOUNTING RAILS <br />USING MODULE LUGS OR RACKING INTEGRATED <br />GROUNDING CLAMPS AS ALLOWED BY LOCAL <br />JURISDICTION. ALL OTHER EXPOSED METAL PARTS <br />SHALL BE GROUNDED USING UL-LISTED LAY-IN LUGS <br />3 <br />INSTALLER SHALL CONFIRM THAT MOUNTING SYSTEM <br />HAS BEEN EVALUATED FOR COMPLIANCE WITH UL 2703 <br />"GROUNDING AND BONDING" WHEN USED WITH <br />PROPOSED PV MODULE <br />4 <br />IF THE EXISTING MAIN SERVICE PANEL DOES NOT HAVE <br />A VERIFIABLE GROUNDING ELECTRODE, IT IS THE <br />CONTRACTOR'S RESPONSIBILITY TO INSTALL A <br />SUPPLEMENTAL GROUNDING ELECTRODE. <br />5 <br />AC SYSTEM GROUNDING ELECTRODE CONDUCTOR <br />(GEC) SHALL BE A MINIMUM SIZE #8AWG WHEN <br />INSULATED, #6AWG IF BARE WIRE. <br />6 <br />EQUIPMENT GROUNDING CONDUCTORS SHALL BE SIZED <br />ACCORDING TO NEC ARTICLE 690.45, AND BE A MINIMUM <br />OF #10AWG WHEN NOT EXPOSED TO DAMAGE, AND <br />#6AWG SHALL BE USED WHEN EXPOSED TO DAMAGE <br />7 <br />GROUNDING AND BONDING CONDUCTORS, IF <br />INSULATED, SHALL BE COLOR CODED GREEN, OR <br />MARKED GREEN IF #4AWG OR LARGER. <br />1 <br />E1.0 <br />SINGLE-LINE DIAGRAM <br />NTS <br />941 W Alton Ave - <br />2017966906/27/23