10180014_4426 W. 1ST - Plan - Laserfiche WebLink

Home Browse Search

115 SIGN COMPONENTS MANUAL (SAM)October 1„ 2013 3. Model PFSC16 is rated 66 W, Model PFSC17 is rated 66W and Model PFSC18 is rated 66W. When units are. connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4 These products are suitable for use in dry. damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Class 2 Power Supply, PS60-12\6108264-DE. PS35-12\/-108264-DE, PS1 5-12V-108264-DE. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one'Class 2 output. 2. These products are provided with the following electrical ratings: Input Voltage Input Freq Input Power Output Output Current OutputModel No (V) (HZ) _Cyrrent (A).Factor Voltage (V dc) (A)Power (W) PS60-12\/-108264-DE 120-240 50/60 0.75 0.95 12 5.0 60 |PS35-12\6108264-DE 120-240 50/60 0.39 0.95 12 2.92 35 PS15-12\/-108264-DE 120-240 50/60 0.35 0.4 12 1.25 15 3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 ih) from end to end and 101.6 mm (4 in) from side to side. 4. These products shall be enclosed in suitable electrical enclosure inythe end product. 5. These products are suitable for factory wiring Only. 6. The load powered by the Class 2 output of these power supplies at the 12 Vdc rating or less is suitable for use in dry, damp and wet locations. 7. These products have been tested in oven at 50°C ambient, with the following maximom case temperatures, Tc: For model LCU 060/12 D the Tc = 82°C: for model LCU 035/12 D XX the Tc =64°C; for model LCU 035/12 D XX the Tc=74*C. 8. These products are intended for use in a dry or damp locations only. 9. The suitability of input/output leads and the wring shall be determined in end product use. 10. The metal case of Model LCU 015/12 D is not grounded. The proper grounding means of this product shall comply with the end product requirements. Class 2 LED Module, designated as "PCSN01". 1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 24 Volt DC or less. 2. When units are connected to a CIass 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place inthe end product by any means available. Class 2 LED Module, designated as "PCSF02". 1. These products are Only suitable for use in dry. damp and wet locations and supplied with a Class 2 power source rated 12.5 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or owtput rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place inthe end product by any means available. Class 2 LED Module, designated as "PCSD02" 1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 30 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 LED Module, designated as "STAR 20" 1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 12.5 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are ffot required to be ehclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. LED Class 2 Power Supply, Model PCDM03. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of two Class 2 output. 2. These products are provided with the following eledtrical ratings: 1Mode Input (V, Hz, A, W)Max Output (\/, A, W) PCDM03 , _ 100-277150602 1.7.150 _ y.0,5.0.60 3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 Inm (1 in.) from end to end, and 101.6 mm (4 in.) from side to side. 4. The suitability of input/output leads and the wring shall be determined in end product use. 5. These products are constant voltage type that requires the proper number of LED modules and controllers that do not exceed the maximum output current. 6. These LED dtivers are intended to be operated on a maximum 20 A branch circuit. 7. These LED drivers are intended for use in fixed equipment only. 8. These products are suitable for dry, damp and wet locations. 9. These; LED drivers do not need to be enclosed in the end product. 10.These products were temperature testes at an elevated ambient of 50°C. LED Tube Lamps, designated "PFXXXHO2S Series", where XXX is the length in inches 24-120. 1