10180014_4426 W. 1ST - Plan - Laserfiche WebLink

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM)116 1. The Temperature Test was conducted with the LED Tube Lamp, Model PFXXH02S installed in Listed fluorescent sighs having a maximum of 2, ten-foot lamps, where the lamps were spaced 1-1/2 inches apart. If the device is used in a different product or configuration consideration shall be given to re-conducting the Temperature Test. 2. The LED Tube Lamps have been evaluated for use in dry and dump locations. The use in other envirenments shall be considered in the end product 3. The Risk of Shock (Pins) was not performed since these lamps are provided with integral leads for conhection to a separate. external LED driver. The end caps are provided with grooves for mechanical support only. 4. Consideration for suitable installation is to be determined in the end-use application. 5. The need for additional end product markings, such as lamp replacement, shall be considered in the end product evaluation. 6. The Normal and Abnormal Operation on Dimmers test has not been conducted. The need for these tests should be considered when the device is connected to a dimmer in the end use. 7. The mounting means of these products shall be determined in the end product applications. Class 2 LED Module, Models "PCSG01 ' and "PCSQ01". 1. These products are suitable for use in dry, damp and wet locations when supplied with a Class 2 power source rated 25 Velt DC orless. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or 0utput rating of the Class 2 supply. 3. These products are not required to be +ehclosed or protected from the weather in the end product. 4. These products may be secured in place in the ehd product by any means available. 5. These products are provided with the following maximum Class 2 input electrical ratings: Model No.I Max. Input Voltage Max. Input Current Max. Power PCSG01 l 25 Vdc 0.4 A 10,W PCSQ01 l 17 Vdc 5A 85 W PERSONAINC 700 21ST ST SW PO BOX 210 E327541 WATERTOWN, SD 57201 Sign Face Tensioning Systems, designated Flex Retro Retainer S-9061, Bleed Flex Retro S-9130, Double Hinge Filter S-9170, Hinge Filler S-9144, Aluminum Spacer 5052-H32, Flex Retro Cover S-9131, Flex Retro Cover S-9072, Flex Retro H-9064, Flex Tensioning Bar S-9062, Wedge Clamp. 1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent entrance of water in outdoor sign applications shall be determined in the end product. 2. This product may be used in dry, damp, or wet locations. 3. Tensioning bar fasteners shall be spaced in the end product as described in the Installation Instructions. 4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent billowing. 5. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face requirements of UL 48,particularly clearance to larnps and lampholders. 6. These clips have been determined to be suitable·with any R/C Flexible Sign Face Material al least 0.020" (0.51 mm) thick. Suitability for use with a material of lesser thickness shall be determined in the end product. PHILIPS LIGHTING BV KANTSINGEL 24 5349 AJ OSS, THE NETHERLANDS E211810 LED power supply with Class 2 outputs, Model 9137 006 208. 1. Model 9137 006 208 is rated for a 100-240 Volts, 50/60 Hz, 25 Watt input and a 24 V DC, 0.83 amp, 20 Watt output. 2. These components are intended for use in dry locations only when not potted. When potted, they are suitable for use in damp locations. 3. These power supplies need to be installed in an enclosure with a means for connection to conduit. 4. A Temperature Test is not required of the power supply when installed in an enclosure having dimensions greater than 13.5 by 6 by 4 inches. When installed in a smaller enclosure. and a Temperature is required, the maximum temperature on the output transfolmer by thermocouple is 904C. 5. The Class 2 output of theseiLED power supplies are acceptable for use in adamp and wet location. LED power supply with Class 2 outputs, Model 913710052466. 1, These components are intended for use in dry locations only when not p0tted. When potted, they are suitable for damp locaUons 2. These power supply needs to be, installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 1 TO° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location Power supply with Class 2 outputs, Model 9137006209. 1. These components are intended for use in dry locations only when not potted, When potted, they are suitable for damp locations. 2. These power supply needs to be installedin an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110°C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location. PHILIPS LIGHTING ELECTRONICS N A OHARE INTERNATIONAL CENTER 10275 W HIGGINS RD E220165 -f