|
SECTION 095113 - ACOUSTICAL PANEL CEILINGS
<br />PART 1 - GENERAL
<br />1.1 RELATED DOCUMENTS
<br />A. DRAWINGS AND GENERAL PROVISIONS OF THE CONTRACT, INCLUDING GENERAL AND
<br />SUPPLEMENTARY CONDITIONS AND DIVISION 01 SPECIFICATION SECTIONS, APPLY TO
<br />THIS SECTION.
<br />1.2 SUMMARY
<br />A. SECTION INCLUDES ACOUSTICAL PANELS AND EXPOSED SUSPENSION SYSTEMS FOR
<br />INTERIOR CEILINGS.
<br />B. PRODUCTS FURNISHED, BUT NOT INSTALLED UNDER THIS SECTION, INCLUDE
<br />ANCHORS, CLIPS, AND OTHER CEILING ATTACHMENT DEVICES TO BE CAST IN
<br />CONCRETE.
<br />1.3 ACTION SUBMITTALS
<br />A. PRODUCT DATA: FOR EACH TYPE OF PRODUCT.
<br />1.4 DELIVERY, STORAGE, AND HANDLING
<br />A. DELIVER ACOUSTICAL PANELS, SUSPENSION-SYSTEM COMPONENTS, AND ACCESSORIES
<br />TO PROJECT SITE AND STORE THEM IN A FULLY ENCLOSED, CONDITIONED SPACE WHERE
<br />THEY WILL BE PROTECTED AGAINST DAMAGE FROM MOISTURE, HUMIDITY,
<br />TEMPERATURE EXTREMES, DIRECT SUNLIGHT, SURFACE CONTAMINATION, AND OTHER
<br />CAUSES.
<br />B. BEFORE INSTALLING ACOUSTICAL PANELS, PERMIT THEM TO REACH ROOM
<br />TEMPERATURE AND A STABILIZED MOISTURE CONTENT.
<br />1.5 FIELD CONDITIONS
<br />A. ENVIRONMENTAL LIMITATIONS: DO NOT INSTALL ACOUSTICAL PANEL CEILINGS UNTIL
<br />SPACES ARE ENCLOSED AND WEATHERTIGHT, WET-WORK IN SPACES IS COMPLETE
<br />AND DRY, WORK ABOVE CEILINGS IS COMPLETE, AND AMBIENT TEMPERATURE AND
<br />HUMIDITY CONDITIONS ARE MAINTAINED AT THE LEVELS INDICATED FOR PROJECT WHEN
<br />OCCUPIED FOR ITS INTENDED USE.
<br />1. PRESSURIZED PLENUMS: OPERATE VENTILATION SYSTEM FOR NOT LESS THAN
<br />48 HOURS BEFORE BEGINNING ACOUSTICAL PANEL CEILING INSTALLATION.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />A. SOURCE LIMITATIONS: OBTAIN EACH TYPE OF ACOUSTICAL CEILING PANEL AND ITS
<br />SUPPORTING SUSPENSION SYSTEM FROM SINGLE SOURCE FROM SINGLE
<br />MANUFACTURER.
<br />2.2 PERFORMANCE REQUIREMENTS
<br />A. SURFACE-BURNING CHARACTERISTICS: COMPLY WITH ASTM E 84; TESTING BY A
<br />QUALIFIED TESTING AGENCY. IDENTIFY PRODUCTS WITH APPROPRIATE MARKINGS OF
<br />APPLICABLE TESTING AGENCY.
<br />1. FLAME-SPREAD INDEX: CLASS B ACCORDING TO ASTM E 1264.
<br />2. SMOKE-DEVELOPED INDEX: 450 OR LESS.
<br />B. FIRE-RESISTANCE RATINGS: COMPLY WITH ASTM E 119; TESTING BY A QUALIFIED
<br />TESTING AGENCY. IDENTIFY PRODUCTS WITH APPROPRIATE MARKINGS OF APPLICABLE
<br />TESTING AGENCY.
<br />1. INDICATE DESIGN DESIGNATIONS FROM UL OR FROM THE LISTINGS OF
<br />ANOTHER QUALIFIED TESTING AGENCY.
<br />2.3 ACOUSTICAL PANELS
<br />A. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE PRODUCTS
<br />BY ONE OF THE FOLLOWING:
<br />1. ARMSTRONG WORLD INDUSTRIES, INC.
<br />2. OR EQUAL
<br />B. REFER TO FINISH SCHEDULE
<br />2.4 METAL SUSPENSION SYSTEM
<br />A. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE PRODUCTS
<br />BY ONE OF THE FOLLOWING:
<br />1. ARMSTRONG WORLD INDUSTRIES, INC.
<br />2. OR EQUAL
<br />B. METAL SUSPENSION-SYSTEM STANDARD: PROVIDE MANUFACTURER'S STANDARD,
<br />DIRECT-HUNG, METAL SUSPENSION SYSTEM AND ACCESSORIES ACCORDING TO ASTM
<br />C 635/C 635M AND DESIGNATED BY TYPE, STRUCTURAL CLASSIFICATION, AND FINISH
<br />INDICATED.
<br />C. WIDE-FACE, CAPPED, DOUBLE-WEB ALUMINUM SUSPENSION SYSTEM: MAIN AND CROSS
<br />RUNNERS ROLL FORMED FROM ALUMINUM SHEET; PREPAINTED, WITH PREFINISHED
<br />15/16-INCH- WIDE ALUMINUM CAPS ON FLANGES.
<br />1. STRUCTURAL CLASSIFICATION: HEAVY-DUTY SYSTEM.
<br />2. END CONDITION OF CROSS RUNNERS: BUTT-EDGE TYPE.
<br />3. FACE DESIGN: FLAT, FLUSH.
<br />4. CAP MATERIAL: ALUMINUM.
<br />5. CAP FINISH: PAINTED WHITE.
<br />2.5 ACCESSORIES
<br />A. ATTACHMENT DEVICES: SIZE FOR FIVE TIMES THE DESIGN LOAD INDICATED IN ASTM C
<br />635/C 635M, TABLE 1, "DIRECT HUNG," UNLESS OTHERWISE INDICATED. COMPLY WITH
<br />SEISMIC DESIGN REQUIREMENTS.
<br />B. WIRE HANGERS, BRACES, AND TIES: PROVIDE WIRES AS FOLLOWS:
<br />1. STAINLESS-STEEL WIRE: ASTM A 580/A 580M, TYPE 304, NONMAGNETIC, AT
<br />KITCHENS AND LAUNDRY.
<br />2. SIZE: WIRE DIAMETER SUFFICIENT FOR ITS STRESS AT THREE TIMES
<br />HANGER DESIGN LOAD (ASTM C 635/C 635M, TABLE 1, "DIRECT HUNG") WILL
<br />BE LESS THAN YIELD STRESS OF WIRE, BUT NOT LESS THAN 0.135-INCH-
<br />DIAMETER WIRE.
<br />C. HANGER RODS: MILD STEEL, ZINC COATED OR PROTECTED WITH RUST-INHIBITIVE PAINT.
<br />D. ANGLE HANGERS: ANGLES WITH LEGS NOT LESS THAN 7/8 INCH WIDE; FORMED WITH
<br />0.04-INCH- THICK, GALVANIZED-STEEL SHEET COMPLYING WITH ASTM A 653/A 653M,
<br />G90 COATING DESIGNATION; WITH BOLTED CONNECTIONS AND 5/16-INCH- DIAMETER
<br />BOLTS.
<br />2.6 METAL EDGE MOLDINGS AND TRIM
<br />A. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE PRODUCTS
<br />BY ONE OF THE FOLLOWING:
<br />1. ARMSTRONG WORLD INDUSTRIES, INC.
<br />2. OR EQUAL
<br />B. ROLL-FORMED, SHEET-METAL EDGE MOLDINGS AND TRIM: TYPE AND PROFILE
<br />INDICATED OR, IF NOT INDICATED, MANUFACTURER'S STANDARD MOLDINGS FOR EDGES
<br />AND PENETRATIONS THAT COMPLY WITH SEISMIC DESIGN REQUIREMENTS; FORMED
<br />FROM SHEET METAL OF SAME MATERIAL, FINISH, AND COLOR AS THAT USED FOR
<br />EXPOSED FLANGES OF SUSPENSION-SYSTEM RUNNERS.
<br />1. EDGE MOLDINGS SHALL FIT ACOUSTICAL PANEL EDGE DETAILS AND
<br />SUSPENSION SYSTEMS INDICATED AND MATCH WIDTH AND CONFIGURATION OF
<br />EXPOSED RUNNERS UNLESS OTHERWISE INDICATED.
<br />2. FOR LAY-IN PANELS WITH REVEAL EDGE DETAILS, PROVIDE STEPPED EDGE
<br />MOLDING THAT FORMS REVEAL OF SAME DEPTH AND WIDTH AS THAT FORMED
<br />BETWEEN EDGE OF PANEL AND FLANGE AT EXPOSED SUSPENSION MEMBER.
<br />3. FOR CIRCULAR PENETRATIONS OF CEILING, PROVIDE EDGE MOLDINGS
<br />FABRICATED TO DIAMETER REQUIRED TO FIT PENETRATION EXACTLY.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION
<br />A. EXAMINE SUBSTRATES, AREAS, AND CONDITIONS, INCLUDING STRUCTURAL FRAMING TO
<br />WHICH ACOUSTICAL PANEL CEILINGS ATTACH OR ABUT, WITH INSTALLER PRESENT, FOR
<br />COMPLIANCE WITH REQUIREMENTS SPECIFIED IN THIS AND OTHER SECTIONS THAT
<br />AFFECT CEILING INSTALLATION AND ANCHORAGE AND WITH REQUIREMENTS FOR
<br />INSTALLATION TOLERANCES AND OTHER CONDITIONS AFFECTING PERFORMANCE OF
<br />ACOUSTICAL PANEL CEILINGS.
<br />B. EXAMINE ACOUSTICAL PANELS BEFORE INSTALLATION. REJECT ACOUSTICAL PANELS
<br />THAT ARE WET, MOISTURE DAMAGED, OR MOLD DAMAGED.
<br />C. PROCEED WITH INSTALLATION ONLY AFTER UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED.
<br />3.2 PREPARATION
<br />A. MEASURE EACH CEILING AREA AND ESTABLISH LAYOUT OF ACOUSTICAL PANELS TO
<br />BALANCE BORDER WIDTHS AT OPPOSITE EDGES OF EACH CEILING. AVOID USING
<br />LESS-THAN-HALF-WIDTH PANELS AT BORDERS UNLESS OTHERWISE INDICATED, AND
<br />COMPLY WITH LAYOUT SHOWN ON REFLECTED CEILING PLANS.
<br />B. LAYOUT OPENINGS FOR PENETRATIONS CENTERED ON THE PENETRATING ITEMS.
<br />3.3 INSTALLATION
<br />A. INSTALL ACOUSTICAL PANEL CEILINGS ACCORDING TO ASTM C 636/C 636M, AND
<br />MANUFACTURER'S WRITTEN INSTRUCTIONS.
<br />1. FIRE-RATED ASSEMBLY: INSTALL FIRE-RATED CEILING SYSTEMS ACCORDING
<br />TO TESTED FIRE-RATED DESIGN.
<br />B. SUSPEND CEILING HANGERS FROM BUILDING'S STRUCTURAL MEMBERS AND AS
<br />FOLLOWS:
<br />1. INSTALL HANGERS PLUMB AND FREE FROM CONTACT WITH INSULATION OR
<br />OTHER OBJECTS WITHIN CEILING PLENUM THAT ARE NOT PART OF
<br />SUPPORTING STRUCTURE OR OF CEILING SUSPENSION SYSTEM.
<br />2. SPLAY HANGERS ONLY WHERE REQUIRED AND, IF PERMITTED WITH
<br />FIRE-RESISTANCE-RATED CEILINGS,TO MISS OBSTRUCTIONS; OFFSET
<br />RESULTING HORIZONTAL FORCES BY BRACING, COUNTERSPLAYING, OR
<br />OTHER EQUALLY EFFECTIVE MEANS.
<br />3. WHERE WIDTH OF DUCTS AND OTHER CONSTRUCTION WITHIN CEILING PLENUM
<br />PRODUCES HANGER SPACINGS THAT INTERFERE WITH LOCATION OF HANGERS
<br />AT SPACINGS REQUIRED TO SUPPORT STANDARD SUSPENSION-SYSTEM
<br />MEMBERS, INSTALL SUPPLEMENTAL SUSPENSION MEMBERS AND HANGERS IN
<br />FORM OF TRAPEZES OR EQUIVALENT DEVICES.
<br />4. SECURE WIRE HANGERS TO CEILING-SUSPENSION MEMBERS AND TO
<br />SUPPORTS ABOVE WITH A MINIMUM OF THREE TIGHT TURNS. CONNECT
<br />HANGERS DIRECTLY TO STRUCTURE OR TO INSERTS, EYE SCREWS, OR OTHER
<br />DEVICES THAT ARE SECURE AND APPROPRIATE FOR SUBSTRATE AND THAT
<br />WILL NOT DETERIORATE OR OTHERWISE FAIL DUE TO AGE, CORROSION, OR
<br />ELEVATED TEMPERATURES.
<br />5. SECURE FLAT, ANGLE, CHANNEL, AND ROD HANGERS TO STRUCTURE,
<br />INCLUDING INTERMEDIATE FRAMING MEMBERS, BY ATTACHING TO INSERTS,
<br />EYE SCREWS, OR OTHER DEVICES THAT ARE SECURE AND APPROPRIATE FOR
<br />BOTH THE STRUCTURE TO WHICH HANGERS ARE ATTACHED AND THE TYPE OF
<br />HANGER INVOLVED. INSTALL HANGERS IN A MANNER THAT WILL NOT CAUSE
<br />THEM TO DETERIORATE OR FAIL DUE TO AGE, CORROSION, OR ELEVATED
<br />TEMPERATURES.
<br />6. DO NOT SUPPORT CEILINGS DIRECTLY FROM PERMANENT METAL FORMS OR
<br />FLOORDECK. FASTEN HANGERS TO CAST-IN-PLACE HANGER INSERTS, POST-
<br />INSTALLED MECHANICAL OR ADHESIVE ANCHORS, OR POWER-ACTUATED
<br />FASTENERS THATEXTENDTHROUGH FORMS INTO CONCRETE.
<br />7. WHEN STEEL FRAMING DOES NOT PERMIT INSTALLATION OF HANGER WIRES
<br />AT SPACING REQUIRED, INSTALL CARRYING CHANNELS OR OTHER
<br />SUPPLEMENTAL SUPPORT FOR ATTACHMENT OF HANGER WIRES.
<br />8. DO NOT ATTACH HANGERS TO STEEL DECK TABS.
<br />9. DO NOT ATTACH HANGERS TO STEEL ROOF DECK. ATTACH HANGERS TO
<br />STRUCTURALMEMBERS.
<br />10. SPACE HANGERS NOT MORE THAN 48 INCHES O.C. ALONG EACH MEMBER
<br />SUPPORTED DIRECTLY FROM HANGERS UNLESS OTHERWISE INDICATED;
<br />PROVIDE HANGERS NOT MORE THAN 8 INCHES FROM ENDS OF EACH MEMBER.
<br />11. SIZE SUPPLEMENTAL SUSPENSION MEMBERS AND HANGERS TO SUPPORT
<br />CEILING LOADS WITHIN PERFORMANCE LIMITS ESTABLISHED BY REFERENCED
<br />STANDARDS.
<br />C. SECURE BRACING WIRES TO CEILING SUSPENSION MEMBERS AND TO SUPPORTS WITH A
<br />MINIMUM OF FOUR TIGHT TURNS. SUSPEND BRACING FROM BUILDING'S STRUCTURAL
<br />MEMBERS AS REQUIRED FOR HANGERS, WITHOUT ATTACHING TO PERMANENT METAL
<br />FORMS, STEEL DECK, OR STEEL DECK TABS. FASTEN BRACING WIRES INTO CONCRETE
<br />WITH CAST-IN-PLACE OR POSTINSTALLED ANCHORS.
<br />D. INSTALL EDGE MOLDINGS AND TRIM OF TYPE INDICATED AT PERIMETER OF ACOUSTICAL
<br />CEILING AREA AND WHERE NECESSARY TO CONCEAL EDGES OF ACOUSTICAL PANELS.
<br />1. APPLY ACOUSTICAL SEALANT IN A CONTINUOUS RIBBON CONCEALED ON
<br />BACK OF VERTICAL LEGS OF MOLDINGS BEFORE THEY ARE INSTALLED.
<br />2. SCREW ATTACH MOLDINGS TO SUBSTRATE AT INTERVALS NOT MORE THAN
<br />16 INCHES O.C. AND NOT MORE THAN 3 INCHES FROM ENDS. MITER CORNERS
<br />ACCURATELY AND CONNECT SECURELY.
<br />3. DO NOT USE EXPOSED FASTENERS, INCLUDING POP RIVETS, ON MOLDINGS
<br />AND TRIM.
<br />E. INSTALL SUSPENSION-SYSTEM RUNNERS SO THEY ARE SQUARE AND SECURELY
<br />INTERLOCKED WITH ONE ANOTHER. REMOVE AND REPLACE DENTED, BENT, OR
<br />KINKED MEMBERS.
<br />F. INSTALL ACOUSTICAL PANELS WITH UNDAMAGED EDGES AND FIT ACCURATELY INTO
<br />SUSPENSION-SYSTEM RUNNERS AND EDGE MOLDINGS. SCRIBE AND CUT PANELS AT
<br />BORDERS AND PENETRATIONS TO PROVIDE PRECISE FIT.
<br />1. ARRANGE DIRECTIONALLY PATTERNED ACOUSTICAL PANELS AS FOLLOWS:
<br />A. INSTALL PANELS WITH PATTERN RUNNING IN ONE DIRECTION
<br />PARALLEL TO SHORT AXIS OF SPACE.
<br />2. FOR SQUARE-EDGED PANELS, INSTALL PANELS WITH EDGES FULLY HIDDEN
<br />FROM VIEW BY FLANGES OF SUSPENSION-SYSTEM RUNNERS AND MOLDINGS.
<br />3. FOR REVEAL-EDGED PANELS ON SUSPENSION-SYSTEM RUNNERS, INSTALL
<br />PANELS WITH BOTTOM OF REVEAL IN FIRM CONTACT WITH TOP SURFACE OF
<br />RUNNER FLANGES.
<br />4. FOR REVEAL-EDGED PANELS ON SUSPENSION-SYSTEM MEMBERS WITH
<br />BOX-SHAPED FLANGES, INSTALL PANELS WITH REVEAL SURFACES IN FIRM
<br />CONTACT WITH SUSPENSION-SYSTEM SURFACES AND PANEL FACES FLUSH
<br />WITH BOTTOM FACE OF RUNNERS.
<br />5. PAINT CUT EDGES OF PANEL REMAINING EXPOSED AFTER INSTALLATION;
<br />MATCH COLOR OF EXPOSED PANEL SURFACES USING COATING
<br />RECOMMENDED IN WRITING FOR THIS PURPOSE BY ACOUSTICAL PANEL
<br />MANUFACTURER.
<br />6. INSTALL HOLD-DOWN AND IMPACT CLIPS IN AREAS INDICATED; SPACE
<br />ACCORDING TO PANEL MANUFACTURER'S WRITTEN INSTRUCTIONS UNLESS
<br />OTHERWISE INDICATED.
<br />A. HOLD-DOWN CLIPS: SPACE 24 INCHES O.C. ON ALL CROSS RUNNERS.
<br />7. PROTECT LIGHTING FIXTURES AND AIR DUCTS ACCORDING TO REQUIREMENTS
<br />INDICATED FOR FIRE-RESISTANCE-RATED ASSEMBLY.
<br />3.4 ERECTION TOLERANCES
<br />A. SUSPENDED CEILINGS: INSTALL MAIN AND CROSS RUNNERS LEVEL TO A TOLERANCE OF
<br />1/8 INCH IN 12 FEET, NON-CUMULATIVE.
<br />B. MOLDINGS AND TRIM: INSTALL MOLDINGS AND TRIM TO SUBSTRATE AND LEVEL WITH
<br />CEILING SUSPENSION SYSTEM TO A TOLERANCE OF 1/8 INCH IN 12 FEET, NON-
<br />CUMULATIVE.
<br />3.5 FIELD QUALITY CONTROL
<br />A. SPECIAL INSPECTIONS: OWNER WILL ENGAGE A QUALIFIED SPECIAL INSPECTOR TO
<br />PERFORM THE FOLLOWING SPECIAL INSPECTIONS:
<br />1. PERIODIC INSPECTION DURING THE INSTALLATION OF SUSPENDED CEILING
<br />GRIDS ACCORDING TO ASCE/SEI 7.
<br />B. TESTING AGENCY: OWNER WILL ENGAGE A QUALIFIED TESTING AGENCY TO PERFORM
<br />TESTS AND INSPECTIONS.
<br />C. PERFORM THE FOLLOWING TESTS AND INSPECTIONS OF COMPLETED INSTALLATIONS
<br />OF ACOUSTICAL PANEL CEILING HANGERS AND ANCHORS AND FASTENERS IN
<br />SUCCESSIVE STAGES AND WHEN INSTALLATION OF CEILING SUSPENSION SYSTEMS ON
<br />EACH FLOOR HAS REACHED 20 PERCENT COMPLETION, BUT NO PANELS HAVE BEEN
<br />INSTALLED. DO NOT PROCEED WITH INSTALLATIONS OF ACOUSTICAL PANEL CEILING
<br />HANGERS FOR THE NEXT AREA UNTIL TEST RESULTS FOR PREVIOUSLY COMPLETED
<br />INSTALLATIONS OF ACOUSTICAL PANEL CEILING HANGERS SHOW COMPLIANCE WITH
<br />REQUIREMENTS.
<br />1. WITHIN EACH TEST AREA, TESTING AGENCY WILL SELECT ONE OF EVERY 10
<br />POWER-ACTUATED FASTENERS AND POSTINSTALLED ANCHORS USED TO
<br />ATTACH HANGERS TO CONCRETE AND WILL TEST THEM FOR 200 LBF OF
<br />TENSION; IT WILL ALSO SELECT ONE OF EVERY TWO POSTINSTALLED ANCHORS
<br />USED TO ATTACH BRACING WIRES TO CONCRETE AND WILL TEST THEM FOR
<br />440 LBF OF TENSION.
<br />2. WHEN TESTING DISCOVERS FASTENERS AND ANCHORS THAT DO NOT COMPLY
<br />WITH REQUIREMENTS, TESTING AGENCY WILL TEST THOSE ANCHORS NOT
<br />PREVIOUSLY TESTED UNTIL 20 PASS CONSECUTIVELY AND THEN WILL RESUME
<br />INITIAL TESTING FREQUENCY.
<br />D. PREPARE TEST AND INSPECTION REPORTS.
<br />3.6 CLEANING
<br />A. CLEAN EXPOSED SURFACES OF ACOUSTICAL PANEL CEILINGS, INCLUDING TRIM, EDGE
<br />MOLDINGS, AND SUSPENSION-SYSTEM MEMBERS. COMPLY WITH MANUFACTURER'S
<br />WRITTEN INSTRUCTIONS FOR CLEANING AND TOUCHUP OF MINOR FINISH DAMAGE.
<br />B. REMOVE AND REPLACE CEILING COMPONENTS THAT CANNOT BE SUCCESSFULLY
<br />CLEANED AND REPAIRED TO PERMANENTLY ELIMINATE EVIDENCE OF DAMAGE.
<br />SECTION 09 6500 - RESILIENT FLOORING
<br />PART 1 - GENERAL
<br />1.1 ACTION SUBMITTALS:
<br />A. PRODUCT DATA: INDICATE PRODUCT CHARACTERISTICS AND INSTALLATION
<br />REQUIREMENTS, INCLUDING MANUFACTURER'S RECOMMENDED ADHESIVES AND
<br />MAINTENANCE INSTRUCTIONS.
<br />B. SAMPLES: SUBMIT FULL SIZE SAMPLES FOR EACH TYPE COLOR AND PATTERN OF
<br />FLORRING AND ACCESSORY REQUIRED.
<br />1.2 QUALITY ASSURANCE:
<br />A. APPLICABLE STANDARDS, AS REFERENCED HEREIN: ASTM INTERNATIONAL (ASTM).
<br />1.3 PROJECT/SITE CONDITIONS:
<br />A. ENVIRONMENTAL REQUIREMENTS:
<br />1. MAINTAIN TEMPERATURE IN SPACE TO RECEIVE RESILIENT MATERIALS AT NOT
<br />LESS THAN 70 DEGREES F. FOR NOT LESS THAN 24 HOURS BEFORE, DURING
<br />AND FOR 48 HOURS AFTER INSTALLATION.
<br />2. MAINTAIN MINIMUM TEMPERATURE OF 55 DEGREES F. AFTER FLOORING IS
<br />INSTALLED, EXCEPT AS SPECIFIED ABOVE, FOR DURATION OF PROJECT.
<br />B. DELIVER VINYL FLOORING AND BASE PRODUCTS TO JOBSITE A MINIMUM OF 24 HOURS
<br />PRIOR TO USE. UNROLL VINYL BASE AND LOW PERCENTAGE RUBBER AND ALLOW TO
<br />RELAX FOR 24 HOURS PRIOR TO USING.
<br />C. PROTECTION: PROTECT FINISHED FLOORING, BASE AND ACCESSORIES FROM
<br />STAINING, MARRING OR OTHER PHYSICAL DAMAGE BY WORK OF OTHER TRADES.
<br />COVER OR MASK SURFACES AS REQUIRED.
<br />PART 2 - PRODUCTS
<br />2.1 RUBBER BASE:
<br />A. ACCEPTABLE MANUFACTURERS:
<br />1. BASIS OF DESIGN; JOHNSONITE, INC.
<br />2. ROPPE CORP.
<br />3. BURKE FLOORING, A DIV. OF BURKE INDUSTRIES
<br />B. CHARACTERISTICS:
<br />1. TYPE: MINIMUM 48% RUBBER, 100% VULCANIZED; MEETING ASTM
<br />F1861-08(2012), TYPE TS THERMOSET VULCANIZED RUBBER SBR.
<br />2. LENGTH: MINIMUM 120'-0" ROLLS.
<br />3. THICKNESS: 1/8".
<br />4. HEIGHT: 4"; TOP SET COVE BASE.
<br />5. STYLE AND COLOR: AS INDICATED IN FINISH SCHEDULE IN DRAWINGS.
<br />2.2 SHEET FLOORING WITH BACKING:
<br />A. ACCEPTABLE MANUFACTURERS:
<br />1. NORA SYSTEMS.
<br />2. ARMSTRONG WORLD INDUSTRIES, INC.
<br />3. SHAW CONTRACT.
<br />4. TARKETT.
<br />B. TYPE: MEETING ASTM F1303-04(2009).
<br />1. TYPE: HETEROGENEOUS, TYPE I, GRADE 1
<br />2. WEAR-LAYER THICKNESS: 0.022 IN.
<br />3. OVERALL THICKNESS: 0.080 IN.
<br />4. BACKING CLASS: CLASS A.
<br />5. FINISH: UV-CURED POLYURETHANE.
<br />6. SIZE: 6 FT. X 82 FT.
<br />7. COLORS AND PATTERNS: AS INDICATED IN FINISH SCHEDULE IN DRAWINGS.
<br />C. FIRE RESISTANCE: CRITICAL RADIENT FLUX MEETING CLASS I, 0.45 WATTS/CM^2 WHEN
<br />TESTED IN ACCORD WITH ASTM E648-10. SMOKE DEVELOPMENT OF 450 OR LESS WHEN
<br />TESTED IN ACCORD WITH ASTM E662-12.
<br />2.3 ACCESSORIES:
<br />A. ACCEPTABLE MANUFACTURERS:
<br />1. BURKE FLOORING PRODUCTS, A DIV. OF BURKE INDUSTRIES.
<br />2. MARLEY FLEXCO (USA), INC.
<br />3. JOHNSONITE, INC.
<br />4. R. C. MUSSON RUBBER CO.
<br />5. ROPPE CORP.
<br />B. REDUCERS:
<br />1. MATERIAL: RUBBER
<br />2. THICKNESS: SAME AS ABUTTING FLOOR MATERIALS.
<br />3. WIDTH(S): 1", UNLESS INDICARTED OTHERWISE.
<br />4. EDGES: TAPERED.
<br />5. COLORS: SUBMIT SAMPLE FOR ARCHITECT'S APPROVAL
<br />2.4 INSTALLATION MATERIALS:
<br />A. LEVELING COMPOUND: ACCEPTABLE PRODUCTS: AS SPECIFIED IN SECTION 03 8215.
<br />B. ADHESIVES: WATER-RESISTANT TYPES AND BRANDS OF ADHESIVE RECOMMENDED BY
<br />FLOORING MATERIAL MANUFACTURER'S PRODUCT DATA FOR INSTALLATION
<br />CONDITIONS INDICATED.
<br />1. VOC CONTENT: ADHESIVES SHALL HAVE A VOC CONTENT LESS THAN THE
<br />CURRENT VOC CONTENT LIMITS OF SOUTH COAST AIR QUALITY MANAGEMENT
<br />DISTRICT (SCAQMD) RULE #1113, ARCHITECTURAL COATINGS, RULES IN
<br />EFFECT JANUARY 1, 2004.
<br />C. CHEMICAL-BONDING COMPOUND: MANUFACTURER'S PRODUCT FOR CHEMICALLY
<br />BONDING SEAMS.
<br />1. VOC CONTENT: VOC CONTENT LESS THAN THE CURRENT VOC CONTENT LIMITS
<br />OF SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD) RULE #1113,
<br />ARCHITECTURAL COATINGS, RULES IN EFFECT JANUARY 1, 2004.
<br />PART 3 - EXECUTION
<br />3.1 PREPARATION:
<br />A. PREPARE SURFACES TO RECEIVE RESILIENT MATERIAL IN ACCORD WITH FLOORING
<br />MANUFACTURER'S INSTRUCTIONS.
<br />B. GRIND HIGH AREAS AND FILL DEPRESSIONS WITH LEVELING COMPOUND WHERE
<br />REQUIRED TO PRODUCE SMOOTH INSTALLATION AND FOR PROPER ALIGNMENT OF
<br />RESILIENT FLOORING WITH ADJACENT FLOORING MATERIALS.
<br />C. PERFORM BOND AND MOISTURE TESTS ON SUBFLOORS IN ACCORD WITH ASTM F2170-11
<br />AND RESILIENT FLOORING MANUFACTURER'S PRODUCT DATA, TO DETERMINE IF
<br />SURFACES ARE ACCEPTABLE TO RECEIVE SPECIFIED RESILIENT FLOORING PRODUCTS.
<br />CORRECT CONDITIONS DETRIMENTAL TO RESILIENT FLOORING INSTALLATION PRIOR
<br />TO STARTING INSTALLATION.
<br />D. REMOVE DIRT, OIL, GREASE OR OTHER FOREIGN MATTER FROM SURFACES TO RECEIVE
<br />FLOOR COVERING OR ACCESSORIES.
<br />3.2 APPLICATION OF ADHESIVES:
<br />A. MIX AND APPLY ADHESIVES IN ACCORD WITH RESILIENT MATERIAL MANUFACTURER'S
<br />PRODUCT DATA. APPLY WITH NOTCHED TROWEL OR OTHER TOOLS AS RECOMMENDED
<br />BY ADHESIVE MANUFACTURER.
<br />2.7 JOINT MATERIALS AND ADHESIVES:
<br />A. STANDARD GYPSUM BOARD PRODUCTS:
<br />1. JOINT TAPE: MEETING ASTM C475-12, PERFORATED PAPER TYPE.
<br />2. JOINT COMPOUND: MEETING ASTM C475-12, READY-MIXED TAPE EMBEDMENT
<br />AND TOPPING COMPOUNDS, VINYL-BASED.
<br />B. MOLD AND MOISTURE RESISTANT PAPER FACED GYPSUM BOARD: JOINT TAPE AND
<br />JOINT COMPOUND SHALL BE IN ACCORD WITH RECOMMENDATIONS OF BOARD
<br />MANUFACTURER'S PRODUCT DATA.
<br />C. JOINT TAPE FOR GLASS MAT-FACED BOARD: FIBERGLASS TAPE, AS HEREIN SPECIFIED.
<br />2.8 ACCESSORIES:
<br />A. ACCESSORIES SHALL COMPLY WITH ASTM C1047-10A
<br />B. CORNER REINFORCEMENT: VINYL CORP., "RIGID VINYL DRYWALL & VENEER
<br />ACCESSORIES, MODEL CBD125 CORNER BEADS"; LEAD-FREE, VIRGIN VINYL COMPOUNDS
<br />CORNER BEADS WITH 1-1/4" X 1-1/4" PERFORATED FLANGES.
<br />C. METAL JAMB, CEILING AND CASING TRIM: MANUFACTURER'S STANDARD "L" AND "U"
<br />SHAPED GALVANIZED MEMBERS WITH FINE EXPANDED MESH FLANGES; "MUD-IN" TYPE
<br />FOR FINISHING WITH JOINT COMPOUNDS.
<br />D. TIE WIRE: MINIMUM 18 GA. GALVANIZED, ANNEALED STEEL WIRE.
<br />E. SPECIAL TRIM SHAPES:
<br />1. ACCEPTABLE MANUFACTURERS; SUBJECT TO COMPLIANCE WITH SPECIFIED
<br />REQUIREMENTS:
<br />A. FRY REGLET CORP.
<br />B. GORDON, INC.
<br />C. PITTCON INDUSTRIES, INC.
<br />2. CHARACTERISTICS:
<br />A. MATERIAL: MANUFACTURER'S STANDARD ALUMINUM ALLOW.
<br />B. FINISH: PAINTED FINISH, COLOR SELECTED BY ARCHITECT.
<br />C. SHAPES: AS INDICATED ON DRAWINGS.
<br />PART 3 - EXECUTION
<br />3.1 FRAMING AND FURRING INSTALLATION:
<br />A. EXCEPT WHERE STRINGENT REQUIREMENTS ARE SPECIFIED, INSTALL FRAMING AND
<br />FURRING IN ACCORD WITH ASTM C754-11, GYPSUM ASSOCIATION REQUIREMENTS AND
<br />MANUFACTURER'S PRODUCT DATA.
<br />B. RUNNERS:
<br />1. ATTACH RUNNER TRACKS AT FLOOR AND UNDERSIDE OF STRUCTURAL DECK
<br />WITH SPECIFIED FASTENERS. PROVIDE SLIP JOINT ATTACHMENTS TO MEET
<br />DEFLECTION CRITERIA AND MANUFACTURER'S CALCULATIONS AT THE
<br />FOLLOWING LOCATIONS:
<br />A. TALL PARTITIONS.
<br />B. FULL-HEIGHT, FLOOR-TO-FLOOR OR FLOOR-TO-DECK PARTITIONS.
<br />C. ALL PARTITIONS SUBJECT TO DEFLECTION.
<br />2. WHERE PARTITIONS ARE INDICATED TO STOP AT FINISH CEILING, ATTACH TO
<br />CEILING SUSPENSION SYSTEM USING 1/8" TOGGLE BOLTS OR SHEET METAL
<br />SCREWS SPACED AT 1'-4" O.C., MAXIMUM, WHERE PARTITION ALIGNS WITH
<br />CEILING GRID. WHERE PARTITION DOES NOT ALIGN WITH GRID, ATTACH AT
<br />EACH INTERSECTION WITH GRID.
<br />C. STUDS:
<br />1. POSITION FULL LENGTH STUDS VERTICALLY, ENGAGING FLOOR AND CEILING
<br />RUNNERS.
<br />A. SPACE STUDS AS INDICATED ON DRAWINGS.
<br />B. SPACE STUDS NOT TO EXXCEED 1'-4" O.C. FOR PARTITIONS TO FRP
<br />PANELS.
<br />2. PROVIDE JUMBO STUDS AT INTERIOR AND EXTERIOR CORNERS, PARTITION
<br />TERMINATION AND ADJACENT TO DOOR AND BORROWED LITE OPENINGS IN
<br />PARTITIONS.
<br />3. SECURE ABUTTING AND INTERSECTING WALLS WITH FASTENERS THROUGH
<br />STUD FLANGES.
<br />4. FOR HORIZONTAL REINFORCEMENT AT DOOR AND BORROWED LITE FRAMES,
<br />INSTALL CUT-TO-LENTH RUNNER SECTIONS WITH SLIT FLANGES SECURED TO
<br />STUDS.
<br />5. INSTALL ACOUSTICAL TAPE ON METAL STUDS WHICH ABUT OTHER STUDS OR
<br />DISSIMILAR SURFACES IN WALLS TO RECEIVE SOUND ATTENUATION BLANKETS.
<br />D. AT LOCATIONS OF ATTACHMENTS TO METAL-FRAMED GYPSUM BOARD PARTITIONS,
<br />PROVIDE MINIMUM 16GA. STEEL PLATE FOR ATTACHMENT. ATTACH TO METAL FRAMING
<br />AS INDIACTED ON DRAWINGS.
<br />3.2 GENERAL BOARD APPLICATION:
<br />A. EXCEPT WHERE MORE STRINGENT REQUIREMENT ARE SPECIFIED, INSTALL GYPSUM
<br />BOARD IN ACCORD WITH ASTM C840-11, GA-216 AND MANUFACTURER'S PRODUCT DATA.
<br />B. INSTALL CEILING PANELS ACROSS FRAMING TO MINIMIZE THE NUMBER OF ABUTTING END
<br />JOINTS AND TO AVOID ABUTTING END JOINTS IN CENTRAL AREA OF EACH CEILING.
<br />STAGGER ABUTTING END JOINTS OF ADJACENT PANELS NOT LESS THAN ONE FRAMING
<br />MEMBER.
<br />C. USE GYPSUM BOARD OF MAXIMUM LENGTHS TO MINIMIZE END JOINTS. STAGGER END
<br />JOINTS.
<br />D. ABUT GYPSUM BOARDS WITHOUT FORCING. FIT ENDS AND EDGES OF BOARD. DO NOT
<br />PLACE BUTT ENDS AGAINST TAPERED EDGES.
<br />E. SUPPORT ENDS AND EDGES OF GYPSUM BOARD PANELS ON FRAMING OR FURRING
<br />MEMBERS, EXCEPT FOR FACE LAYER OF DOUBLE LAYER WORK.
<br />F. INSTALL GYPSUM BOARD ACCESSORIES IN ACCORD WITH GYPSUM BOARD
<br />MANUFACTURER'S PRODUCT DATA AND AS FOLLOWS:
<br />1. CORNER BEAD: INSTALL VINYL CORNER BEADS AT EXTERNAL CORNERS.
<br />2. METAL TRIM SHAPES: AT EXPOSED EDGE OF GYPSUM BOARD AT DOOR AND
<br />WINDOW OPENINGS, AT INTERSECTIONS WITH OTHER MATERIALS AND AT
<br />INTERSECTION OF WALLS WITH CEILINGS.
<br />3. INSTALL CORNER BEADS AND METAL TRIM SHAPES TO FRAMING SYSTEM WITH
<br />MECHANICAL ANCHORS.
<br />G. INSTALL ACOUSTICAL SEALANT AT SOUND-RATED PARTITIONS:
<br />1. SEAL PARTITION PERIMETER WITH CONTINUOUS 1/4" MINIMUM ROUND BEAD OF
<br />ACOUSTICAL SEALANT APPLIED TO EACH LEG OF RUNNERS, INCLUDING THOSE
<br />USED AT PARTITION INTERSECTIONS WITH DISSIMILAR WALL CONSTRUCTION.
<br />2. INSTALL GYPSUM BOARD WITH 1/8" PERIMETER RELIEF COMPRESSING SEALANT
<br />TO FORM PERMANENT AIRTIGHT SEAL.
<br />3. WHERE SLIP JOINT ATTACHMENTS ARE REQUIRED AT TOP OF PARTITIONS, FILL
<br />RESULTING JOINT BETWEEN DRYWALL AND ADJACENT STRUCTURE WITH
<br />ACOUSTICAL SEALANT TO FORM PERMANENT AIR TIGHT SEAL.
<br />4. APPLY ACOUSTICAL SEALANT AROUND CUTOUTS SUCH AS AT ELECTRICAL
<br />BOXES, PLUMBING PENETRATIONS, MEDICINE CABINETS, HEATING DUCTS AND
<br />COLD AIR RETURNS TO FORM PERMANENT AIRTIGHT SEAL. (SEALANT SHALL
<br />NOT BE USED AS A FIRE STOPPING MATERIAL.)
<br />H. INSTALL MOLD-MOISTURE RESISTANT GYPSUM BOARD IN DAMP, MOIST LOCATIONS.
<br />I. CONTINUE REQUIRED COMPONENTS OF FIRE-RATED AND ACOUSTICALLY RATED WALL
<br />ASSEMBLY TO OVERHEAD STRUCTURE. APPLY JOINT TAPE AND ONE COAT OF
<br />COMPOUND TO GYPSUM BOARD JOINTS CONCEALED FROM VIEW IN COMPLETED WORK.
<br />J. IDENTIFICATION:
<br />1. FIRE, WALLS, FIRE BARRIERS, FIRE PARTITIONS, SMOKE BARRIERS AND SMOKE
<br />PARTITIONS OR ANY OTHER WALL REQUIRED TO HAVE PROTECTED OPENINGS
<br />SHALL BE EFFECTIVELY AND PERMANENTLY IDENTIFIED WITH SIGNS OR
<br />STENCILING IN A MANNER ACCEPTABLE TO THE AUTHORITY HAVING
<br />JURISDICTION.
<br />2. SUCH IDENTIFICATION SHALL BE ABOVE ANY DECORATIVE CEILING AND IN
<br />CONCEALED SPACES.
<br />3. SUGGESTED WORDING FOR FIRE AND SMOKE BARRIERS: "_____ HOUR FIRE AND
<br />SMOKE BARRIER - PROTECT ALL OPENINGS."
<br />K. ALLOWABLE TOLERANCES IN FRAMED GYPSUM BOARD CONSTRUTION.
<br />1. POSITION: + - 1/4" MAXIMUM VARIATION FROM DESIGN POSITIOIN.
<br />2. ALIGNMENT: 1/8" IN 8'-0"; 1/4" MAXIMUM IN ANY CONTINOUS WALL, LINE OR
<br />SURFACE.
<br />3. SURFACE PLANE: 1/8" IN 12-0"; 1/16" IN 1'-0", MAXIMUM VARIATION IN TRUE
<br />SURFACE
<br />PLANE.
<br />4. SURFACE SMOOTHNESS: NO JOINT OR FASTENER LOCATION, ROUGHNESS OR
<br />BLEMISH DISCERNIBLE AFTER APPLICATION OF FINISH WHEN VIEWED AT ANY
<br />ANGLE FROM A DISTANCE OF 5'-0" UNDER OCCUPANCY LIGHTING CONDITIONS,
<br />WITH SURFACE PREPARATION AS SPECIFIED IN PAINTING AND COATING
<br />SECTION.
<br />L. ALLOWABLE TOLERANCES IN SUSPENDED GYPSUM BOARD FURRING SYSTEM CEILINGS:
<br />1. DEFLECTION: SUSPENSION SYSTEM COMPONENTS, HANGERS AND FASTENING
<br />DEVICES SUPPORTING LIGHTING FIXTURES, CEILING GRILLES AND ACOUSTICAL
<br />UNITS SHALL HAVE MAXIMUM DEFLECTION OF 1/360 OF SPAN WHEN TESTED IN
<br />ACCORD WITH ASTM C635-07.
<br />2. BOW, CAMBER AND TWIST: NOT EXCEEDING TOLERANCES ESTABLISHED BY
<br />ASTM C635-07.
<br />3. VARIATION FROM LEVEL IN FINISHED CEILING: 1/8" IN 12'-0".
<br />4. VARIATION IN PLANE OF ADJACENT GYPSUM BOARD PANELS PRIOR TO JOINT
<br />TREATMENT: 1/16".
<br />3.3 SINGLE LAYER APPLICATION:
<br />A. CEILING: APPLY GYPSUM BOARD WITH LONG DIMENSION AT RIGHT ANGLES TO FRAMING.
<br />TERMINATE EDGES OF GYPSUM BOARD RUNNING PARALLEL TO FRAMING ON FRAMING
<br />MEMBERS.
<br />B. WALLS:
<br />1. APPLY GYPSUM BOARD VERTICALLY AND HORIZONTALLY AT CONTRACTOR'S
<br />OPTION, EXCEPT AS REQUIRED BY GYPSUM BOARD MANUFACTURER'S
<br />PRODUCT DATA FOR SYSTEM DESIGNS, INCLUDING FIRE-RATED AND
<br />ACOUSTICALLY-RATED
<br />PARTITIONS.
<br />2. STAGGER END JOINTS IN OPPOSITE SIDES OF PARTITIONS.
<br />3. TERMINATE EDGES OF GYPSUM BOARD RUNNING PARALLEL TO FRAMING,
<br />FURRING ON FRAMING OR FURRING MEMBERS.
<br />C. FASTENING: ATTACH GYPSUM BOARD USING FASTENERS SPECIFIED AT SPACING
<br />REQUIRED BY MANUFACTURER'S PRODUCT DATA.
<br />3.4 JOINT TREATMENT:
<br />A. FINISH LEVELS SHALL BE IN ACCORD WITH THE "RECOMMENDED SPECIFICATON: LEVELS
<br />OF GYPSUM BOARD FINISH" AS PUBLISHED JOINTLY BY THE GYPSUM ASSOCIATION,
<br />AWCI, CISCA, AND PDCA.
<br />B. FINISH LEVEL 1; JOINT TREATMENT FOR NON-PUBLIC, NON-SERVICE AREAS TO RECEIVE
<br />NO FURTHER FINISH, INCLUDING STORAGE AREAS: APPLY JOINT COMPOUND TO JOINTS
<br />AND ANGLES IN GYPSUM BOARD AND EMBED JOINT TAPE. SURFACE SHALL BE FREE OF
<br />EXCESS JOINT COMPOUND; TOOL MARKS AND RIDGES ARE ACCEPTABLE.
<br />C. FINISH LEVEL 2; JOINT TREATMENT FOR AREAS INDICATED TO RECEIVE NO FURTHER
<br />FINISH; APPLY JOINT COMPOUND TO JOINTS, ANGLES, FASTENER HEADS AND
<br />ACCESSORIES. EMBED JOINT TAPE. APPLY ONE ADDITIONAL COAT OR COMPOUND OVER
<br />TAPE. APPLY ONE COAT OF COMPOUND TO FASTENER DEPRESSIONS. SURFACES SHALL
<br />BE FREE OF EXCESS JOINT COMPOUND; TOOL MARKS AND RIDGES ARE ACCEPTABLE.
<br />D. FINISH LEVEL 4; JOINT TREATMENT FOR AREAS INDICATED TO RECEIVE SEMI-GLOSS AND
<br />EGGSHELL PAINT FINISHES:
<br />1. APPLY JOINT COMPOUND TO JOINTS, ANGLES, FASTENER HEADS AND
<br />ACCESSORIES. EMBED JOINT TAPE. APPLY THREE ADDITIONAL COATS OF
<br />COMPOUND OVER TAPE, FEATHEREDGING AND SANDING EACH COAT.
<br />2. APPLY MINIMUM OF THREE COATS OF COMPOUND TO FASTENER DEPRESSIONS,
<br />SANDING EACH COAT AND BRINGING TO LEVEL PLANE WITH GYPSUM BOARD
<br />SURFACE.
<br />3. ALL JOINT COMPOUND SHALL BE FREE OF TOOL MARKS AND RIDGES.
<br />E. FASTENER POP: DRIVE NEW FASTENER APPROXIMATELY 1-1/2" FROM POPPED FASTENER
<br />AND REPAIR TO MATCH GYPSUM BOARD FINISH.
<br />F. FILL CRACKS WITH JOINT COMPOUND AND SAND SMOOTH AND FLUSH.
<br />G. DUST SURFACES AND LEAVE READY FOR DECORATION. JOINT AND FASTENER
<br />TREATMENT SHALL BE INDISTINGUISHABLE IN FINISHED WORK.
<br />END OF SECTION
<br />B. PROVIDE SAFETY PRECAUTIONS DURING MIXING AND APPLICATIONS AS RECOMMENDED
<br />BY ADHESIVE MANUFACTURER.
<br />C. APPLY ADHESIVE TO ONLY THAT AREA WHICH CAN BE COVERED BY RESILIENT
<br />MATERIAL WITHIN THE RECOMMENDED WORKING TIME OF THE ADHESIVE.
<br />1. REMOVE ADHESIVE WHICH DRIES OR FILMS OVER.
<br />2. DO NOT SOIL WALLS, BASES OR ADJACENT AREAS WITH ADHESIVES.
<br />3. REMOVE SPILLED OR MISPLACED MATERIALS.
<br />3.3 INSTALLATION OF VINYL SHEET FLOORING:
<br />A. WORKMANSHIP:
<br />1. INSTALL SHEET MATERIAL IN ACCORD WITH RFCI SPECIFICATIONS IS-1 AND
<br />WITH FLOORING MANUFACTURER'S PRODUCT DATA.
<br />2. CUT SHEET MATERIAL IN LENGTHS AND SIZES REQUIRED; COMPLY WITH
<br />MANUFACTURER'S CUTTIG AND FITTING INSTRUCTIONS.
<br />3. LAY CUT SHEETS FLAT AND ALLOW TO ACCLIMATIZE TO ROOM TEMPERATURE
<br />PRIOR TO SECURING IN PLACE.
<br />B. APPLY FULL BED OF ADHESIVE UNIFORMLY OVER EXPOSED SUBFLOOR. TURN SHEET
<br />BACK INTO WET ADHESIVE.
<br />C. WORK OUT WRINKLES AND AIR POCKETS. ROLL MATERIAL IN TWO DIRECTIONS
<br />STARTING AT CENTER OF SHEET.
<br />3.4 INSTALLATION OF BASE:
<br />A. WORKMANSHIP:
<br />1. UNROLL BASE MATERIAL AND ALLOW TO RELAX FOR 24 HOURS, MINIMUM,
<br />PRIOR TO INSTALLATION. CUT INTO LENGTHS FOR MINIMUM NUMBER OF
<br />JOINTS. DOUBLE-CUT ADJOINING LENGTHS.
<br />2. INSTALL WITH TIGHT BUTT JOINTS WITH NO JOINT WIDTHS GREATER THAN
<br />1/64".
<br />B. TOP-SER BASE:
<br />1. APPLY ADHESIVE AND ADHERE TO VERTICAL SURFACES.
<br />2. PRESS DOWN SO THAT BOTTOM EDGE FOLLOWS FLOOR PROFILE.
<br />3. FORM INTERNAL CORNERS USING PREMOLDED CORNERS.
<br />4. FORM EXTERNAL CORNERS USING PREMOLDED CORNERS.
<br />5. SCRIBE BASE TO ABUTTING MATERIALS.
<br />3.5 ACCESSORY INSTALLATION:
<br />A. CUT MATERIALS TO LENGTHS AND SIZES INDICATED.
<br />B. RESILIENT REDUCERS:
<br />1. APPLY ADHESIVES AND BOND TO SUBSTRATE.
<br />2. CENTER AND REDUCERS IN DOOR OPENINGS.
<br />3. FIT EDGE TO DOOR FRAME JAMBS WITHOUT VISIBLE GAPS OR CRACKS.
<br />4. FIT EDGES TO ABUTTING FLOOR MATERIALS FOR FLUSH FIT.
<br />3.6 CLEANING:
<br />A. UPON COMPLETION OF INSTALLATION, CLEAN SURFACES USING A NEUTRAL CLEANER
<br />ACCEPTABLE TO MATERIAL MANUFACTURER.
<br />B. JUST PRIOR TO DATE OF SUBSTANTIAL COMPLETION, BUFF NO-WAX FLOORS USING
<br />BUFFING COMPOUND FOR NO-WAX FINISH. FOR INDICATED FLOORING TYPES, APPLY
<br />TWO COATS OF NON-SLIP WAX TO CLEAN WAXABLE FLOOR SURFACES AND BUFF.
<br />3.7 MAINTENANCE MATERIAL:
<br />A. SALVAGE SCRAPS FROM INSTALLATION OF SHEET FLOORING GOODS OVER THREE SQ.
<br />FT. IN AREA AND OVER 1'-0" IN WIDTH FOR OWNER'S USE.
<br />END OF SECTION
<br />SECTION 09 9000 - PAINTING AND COATING
<br />PART 1 - GENERAL
<br />1.1 SUMMARY:
<br />A. WORK OF THIS SECTION INCLUDES:
<br />1. TOUCHING UP OF SHOP-APPLIED PRIME COATS.
<br />2. PREPARATION OF SURFACES TO RECEIVE FINISHES.
<br />3. PAINTING, OR OTHERWISE FINISHING OF SURFACES, EXCEPT AS OTHERWISE
<br />INDICATED.
<br />B. RELATED WORK SPECIFIED ELSEWHERE:
<br />1. SHOP-APPLIED PRIMER COATS.
<br />2. JOINT SEALANTS.
<br />3. PIPING IDENTIFICATON.
<br />4. PREFINISHED ITEMS.
<br />1.2 DEFINITIONS:
<br />A. STANDARD COATING TERMS: AS DEFINED IN ASTM D16-12.
<br />B. COMMERCIAL: PAINTER GRADE PRODUCTS.
<br />C. DFT: DRY FILM THICKNESS OF THE COATING.
<br />D. PREMIUM: BEST QUALITY PRODUCT (TOP OF THE LINE):
<br />E. VOC: VOLATILE ORGANIC COMPOUNDS FOUND IN PRIMERS, PAINTS, SEALERS AND
<br />STAINS. VOC LEVELS ARE DESIGNATED IN GRAMS PER LITER (g/L).
<br />1.3 PERFORMANCE REQUIREMENTS:
<br />A. DFT FOR EACH PRIMER, PAINT, SEALER AND STAIN SHALL BE AS RECOMMENDED BY
<br />PRODUCT MANUFACTURER'S PRODUCT DATA.
<br />B. VOC CONTENT: PAINTS, PRIMERS, AND SEALERS SHALL HAVE A VOC CONTENT LESS
<br />THAN THE CURRENT VOC CONTENT LIMITS OF SOUTH COAST AIR QUALITY
<br />MANAGEMENT DISTRICT (SCAQMD) RULE #1113, ARCHITECTURAL COATINGS, RULES IN
<br />EFFECT JANUARY 1, 2004.
<br />1.4 ACTION SUBMITTALS:
<br />A. PRODUCT DATA:
<br />1. SUBMIT COMPLETE LIST OF PRODUCTS PROPOSED FOR USE AT LEAST 30 DAYS
<br />PRIOR TO COMMENCEMENT OF PAINTING WORK.
<br />2. INDICATE MANUFACTURER, BRAND NAME, QUALITY, TYPE, AND SHEEN FOR
<br />EACH TYPE OF PAINT AND FOR EACH SURFACE TO BE FINISHED. INDICATE VOC
<br />RATING AND COMPLIANCE WITH APPLICABLE REGULATIONS.
<br />3. INDICATE MANUFACTURER'S INSTRUCTIONS REGARDING MIXING, SURFACE
<br />PREPARATION AND APPLICATION. INCLUDE APPLICATION RATES, FILM
<br />THICKNESS AND REQUIRED PRIMERS.
<br />4. INTENT OF CONTRACTOR TO USE PRODUCTS SPECIFIED DOES NOT RELIEVE
<br />HIM FROM HIS RESPONSIBILITIES OF SUBMITTING PRODUCT LIST.
<br />B. VERIFICATION SAMPLES: SUBMIT TWO SETS OF SELECTED COLOR SAMPLES FROM
<br />PAINT MANUFACTURER FOR ARCHITECT'S REVIEW AND ACCEPTANCE.
<br />1.5 QUALITY ASSURANCE:
<br />A. APPLICABLE STANDARDS:
<br />1. ASTM INTERNATIONAL (ASTM), AS REFERENCED HEREIN.
<br />2. ENVIRONMENTAL PROTECTION AGENCY (EPA), VOLATILE ORGANIC
<br />COMPOUNDS (VOC) STANDARDS AS REQUIRED BY LOCAL CODES AND
<br />REGULATIONS.
<br />1.6 DELIVERY, STORAGE AND HANDLING:
<br />A. DELIVERY: DELIVER MATERIALS TO PROJECT SITE READY-MIXED IN ORIGINAL
<br />CONTAINERS WITH LABELS INTACT; LABELS BEARING MANUFACTURER'S NAME, PAINT
<br />TYPE, COLOR AND RECOMMENDED INSTALLATION AND REDUCING PROCEDURES.
<br />B. STORAGE AND HANDLING:
<br />1. STORE MATERIALS IN LOCATION ACCEPTABLE TO ARCHITECT.
<br />2. MAINTAIN NEAT, CLEAN CONDITIONS IN STORAGE AREA; REMOVE RAGS AND
<br />WASTE MATERIALS AT END OF EACH DAY'S WORK.
<br />3. CLOSE CONTAINERS AT END OF DAY'S WORK. LEAVE NO MATERIALS OPEN.
<br />1.7 PROJECT/ SITE CONDITIONS:
<br />A. ENVIRONMENTAL REQUIREMENTS:
<br />1. COMPLY WITH MANUFACTURER'S PRODUCT DATA AS TO ENVIRONMENTAL
<br />CONDITIONS UNDER WHICH MATERIALS MAY BE APPLIED.
<br />2. APPLY NO MATERIALS IN SPACES WHERE DUST IS BEING GENERATED.
<br />3. COMPLY WITH APPLICABLE VOC REGULATIONS.
<br />B. PROTECTION: COVER FINISHED WORK OF OTHER TRADES AND SURFACES NOT BEING
<br />PAINTED CONCURRENTLY AND PREFINISHED ITEMS.
<br />C. SAFETY PRECAUTIONS:
<br />1. PROVIDE TEMPORARY FIRE PROTECTION EQUIPMENT IN MATERIALS STORAGE
<br />AREA.
<br />2. PROHIBIT SMOKING IN STORAGE AREA.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS:
<br />A. ACCEPTABLE MANUFACTURERS: EXCEPT AS OTHERWISE NOTED, PRODUCTS SPECIFIED
<br />AS A STANDARD OF QUALITY ARE MANUFACTURED BY BENJAMIN MOORE CO.
<br />PRODUCTS OF THE FOLLOWING MANUFACTURERS SIMILAR IN TYPE AND QUALITY ARE
<br />ACCEPTABLE FOR USE, SUBJECT TO APPROVAL OF PRODUCT LIST:
<br />1. FRAZEE PAINT.
<br />2. DUNN-EDWARDS CORPORATION.
<br />3. SHERWIN-WILLIAMS.
<br />B. WHERE PRODUCTS OTHER THAN THOSE OF THE MANUFACTURER LISTED AS THE
<br />STANDARD OF QUALITY ARE SPECIFIED IN PAINTING SCHEDULE, SUCH PRODUCTS HAVE
<br />BEEN SELECTED TO ACHIEVE SPECIFIC RESULTS AND SUBSTITUTIONS WILL BE
<br />ALLOWED ONLY IN ACCORD WITH PRODUCT SUBSTITUTION PROCEDURES SECTION.
<br />2.2 PAINTING MATERIALS:
<br />A. MISCELLANEOUS MATERIALS:
<br />1. PAINT THINNERS AND TINTS SHALL BE PRODUCTS OF SAME MANUFACTURER
<br />AS PAINTS OR APPROVED BY HIM FOR USE WITH HIS PRODUCTS.
<br />2. SHELLAC, TURPENTINE, PATCHING COMPOUNDS AND SIMILAR MATERIALS
<br />REQUIRED FOR EXECUTION OF WORK SHALL BE PURE, BEST QUALITY
<br />PRODUCTS.
<br />B. PAINT AND STAIN COLORS SHALL BE AS INDICATED ON FINISH SCHEDULE WITH FINAL
<br />APPROVAL BASED ON BRUSH-OUT SUBMITTAL.
<br />PART 3 - EXECUTION
<br />3.1 PREPARATION:
<br />A. INCLUDE PAINTING REQUIRED BY PROJECT EXCEPT FOR PREFINISHED ITEMS AND
<br />SPECIAL FINISHES AS SPECIFIED IN OTHER SECTIONS.
<br />B. EXISTING SURFACES:
<br />1. FOR PREVIOUSLY PAINTED SURFACES, REMOVE DIRT, DEBRIS AND CHALK BY
<br />WASHING WITH DETERGENT AND WATER.
<br />2. PREVIOUSLY PAINTED METAL SURFACES TO REMAIN SHALL BE WIRE-BRUSHED
<br />AND CLEANED OF EXISTING PAINT AND RUST.
<br />3. TREAT MILDEWED SURFACES WITH A SOLUTION OF ONE QUART
<br />HYPOCHLORITE BLEACH TO A HALF CUP OF DETERGENT TO ONE GALLON
<br />WATER. RINSE AND ALLOW TO DRY PRIOR TO PAINTING.
<br />4. SCRAPE OR USE APPROPRIATE MEANS TO REMOVE ALL LOOSE, PEELING,
<br />FLAKING, OR MARGINALLY ADHERING PAINT FROM THE SURFACE. FEATHER
<br />SAND EDGES AS NECESSARY.
<br />5. REPAIR OR REPLACE CAULKING WHERE NEEDED.
<br />6. AFTER CLEANING, GLOSSY SURFACES SHALL BE DULLED BY SANDING.
<br />REMOVE ALL SANDING DUST FROM THE SURFACE AFTER SANDING HAS TAKEN
<br />PLACE.
<br />7. PREPARE BARE AREAS AS NEW SURFACES, AND STOP PRIME OR FILL THOSE
<br />AREAS WITH THE APPROPRIATE PRIMER OR FILLER.
<br />8. PATCH OR REPAIR ALL CRACKS OR VOIDS WITH THE APPROPRIATE PATCHING
<br />COMPOUND AND SAND SMOOTH AS NECESSARY.
<br />9. SPOT PRIME ALL PATCHED AREAS WITH THE APPROPRIATE PRIMER PRIOR TO
<br />FINISHING.
<br />10. IF AFTER CLEANING CHALKY SURFACES CHALK RESIDUE IS STILL PRESENT,
<br />PRIME THE ENTIRE SURFACE WITH THE PROPER BONDING PRIMER TO INSURE
<br />GOOD ADHESION OF THE TOPCOAT TO THE SUBSTRATE.
<br />C. WHERE FINISH MATERIALS ABUT OR ARE ABUTTED BY DISSIMILAR MATERIALS, CAULK
<br />JOINTS IN ACCORD WITH JOINT SEALANTS SECTION.
<br />D. GYPSUM BOARD:
<br />1. FILL NARROW, SHALLOW CRACKS AND SMALL HOLES WITH PATCHING
<br />COMPOUND, ALLOW TO DRY AND SAND SMOOTH WITHOUT RAISING NAP OF
<br />GYPSUM BOARD PAPER.
<br />2. GYPSUM BOARD SHALL BE FINISHED AS SPECIFIED IN GYPSUM BOARD
<br />SECTION PRIOR TO PAINTING.
<br />E. FERROUS METALS:
<br />1. WIRE-BRUSH OR SANDPAPER TO REMOVE RUST AND MILL SCALE.
<br />2. SOLVENT-CLEAN WITH XYLOL TO REMOVE GREASE, OIL AND CONTAMINANTS.
<br />WIPE DRY WITH CLEAN CLOTH.
<br />3.2 APPLICATIOIN:
<br />A. APPLY PAINT ONLY WHEN MOISTURE CONTENT OF SURFACES IS WITHIN LIMITS
<br />RECOMMENDED IN PRODUCT DATA. APPLY PAINT MATERIALS USING CLEAN BRUSHES,
<br />ROLLERS OR SPRAYING EQUIPMENT.
<br />B. APPLY MATERIALS AT RATE NOT EXCEEDING THAT RECOMMENDED IN PRODUCT DATA
<br />FOR SURFACE BEING PAINTED, LESS TEN PERCENT FOR LOSSES.
<br />C. COMPLY WITH PRODUCT DATA FOR DRYING TIME BETWEEN COATS.
<br />D. SAND AND DUST BETWEEN COATS TO REMOVE DEFECTS VISIBLE FROM A DISTANCE OF
<br />5'-0".
<br />E. FINISH COATS SHALL BE SMOOTH, FREE OF BRUSH MARKS, STREAKS, LAPS OR PILE-UP
<br />OF PAINT, SKIPPED OR MISSED AREAS.
<br />F. MAKE EDGES OF PAINT ADJOINING OTHER MATERIALS OR COLORS CLEAN AND SHARP
<br />WITHOUT OVERLAPPING.
<br />G. PRIMER COATS MAY BE OMITTED FOR SURFACES SPECIFIED TO RECEIVE FACTORY-
<br />APPLIED PRIMER, IF PRIMER IS COMPATIBLE WITH FINISH COATS. IF PRIMER COATS ARE
<br />NOT COMPATIBLE, SUBSTITUTE A BOND COAT AS RECOMMENDED BY PAINT
<br />MANUFACTURER FOR SPECIFIED PRIMER COAT.
<br />H. WHERE TWO-COAT FINISH IS SPECIFIED, PRIME COAT SHALL BE TINTED TO
<br />APPROXIMATE FINISH COLOR.
<br />I. WHERE PORTION OF FINISH ON GYPSUM BOARD PARTITION IS DAMAGED OR
<br />UNACCEPTABLE, REFINISH ENTIRE SURFACE OF PARTITION.
<br />J. SEAL TOPS AND BOTTOMS OF INTERIOR DOORS WITH PRIME COAT ONLY; SIDE EDGES
<br />SAME AS FACES.
<br />K. REMOVE AND PROTECT HARDWARE, ACCESSORIES, DEVICE PLATES, LIGHTING
<br />FIXTURES, FACTORY-FINISHED WORK AND SIMILAR ITEMS, OR PROVIDE IN-PLACE
<br />PROTECTION. UPON COMPLETION OF EACH SPACE, REPLACE REMOVED ITEMS.
<br />L. PAINT EXPOSED PIPING AND DUCKWORK IN PAINTED SPACES SAME AS ADJACENT
<br />WALL SURFACES.
<br />M. THE FOLLOWING SURFACES DO NOT REQUIRE PAINTING:
<br />1. PREFINISHED AND FACTORY-FINISHED SURFACES AND ITEMS, EXCEPT WHERE
<br />INDICATED OTHERWISE.
<br />2. CONCEALED DUCKWORK, CONDUIT AND PIPING.
<br />3.3 PAINT SCHEDULES:
<br />A. INTERIOR PAINT SCHEDULE:
<br />1. GYPSUM BOARD: PROVIDE THE FOLLOWING FINISH SYSTEMS OVER INTERIOR
<br />GYPSUM BOARD SURFACES:
<br />A. LOW-LUSTER ACRYLIC EGGSHELL FINISH:
<br />1) FIRST COAT OVER BARE DRYWALL: MOORE #023 FRESH START
<br />ACRYLIC LATEX PRIMER 50 g/L 1.3 MILS DFT.
<br />2) FIRST COAT OVER PREVIOUSLY PAINTED DRYWALL: MOORE
<br />#SXA-110 STIX WATERBORNE BONDING PRIMER 40% VOL
<br />SOLIDS, 2.1 MILS DFT.
<br />3) SECOND COAT: MOORE #N538 ULTRA SPEC 500, ZERO VOC,
<br />ACRYLIC EGGSHELL ENAMEL, 1.8 MILS DFT.
<br />4) THIRD COAT: MOORE #N538 ULTRA SPEC 500, ZERO VOC,
<br />ACRYLIC EGGSHELL ENAMEL, 1.8 MILS DFT.
<br />2. FERROUS METAL: PROVIDE THE FOLLOWING FINISH SYSTEMS OVER NEW AND
<br />PREVIOUSLY PAINTED FERROUS METAL:
<br />A. SEMI-GLOSS ACRYLIC ENAMEL FINISH:
<br />1) FIRST COAT: MOORE #P04 SUPER SPEC HP ACRYLIC METAL
<br />PRIMER 54 g/L, 2.3 MILS DFT.
<br />2) SECOND COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />3) THIRD COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />3. ZINC-COATED METAL: PROVIDE THE FOLLOWING FINISH SYSTEMS OVER NEW
<br />AND PREVIOUSLY PAINTED INTERIOR ZINC-COATED METAL SURFACES:
<br />A. SEMI-GLOSS ACRYLIC ENAMEL FINISH:
<br />1) FIRST COAT: MOORE #P04 SUPER SPEC HP ACRYLIC METAL
<br />PRIMER 54 g/L, 2.3 MILS DFT.
<br />2) SECOND COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />3) THIRD COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />4. ALUMINUM: PROVIDE THE FOLLOWING FINISH SYSTEMS OVER NEW AND
<br />PREVIOUSLY PAINTED INTERIOR ALUMINUM METAL SURFACES:
<br />A. SEMI-GLOSS ACRYLIC ENAMEL FINISH:
<br />1) FIRST COAT: MOORE #SXA-110 STIX BONDING PRIMER 40%
<br />VOL. SOLIDS, 2.1 MILS DFT.
<br />2) SECOND COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />3) THIRD COAT: MOORE #P29 SUPER SPEC HP ACRYLIC DTM
<br />SEMI-GLOSS ENAMEL, 206 g/L, 2.5 MILS DFT.
<br />END OF SECTION
<br />DIVISION 10 - SPECIALTIES
<br />SECTION 10 2123 - CUBICLE TRACK AND CURTAINS
<br />PART 1 - GENERAL
<br />1.1 SUMMARY:
<br />A. WORK OF THIS SECTION INCLUDES CUBICLE CURTAIN TRACK, CURTAINS AND
<br />ACCESSORIES.
<br />B. RELATED WORK SPECIFIED ELSEWHERE:
<br />1. ROUGH CARPENTRY.
<br />2. ACOUSTICAL CEILINGS.
<br />1.2 SUBMITTALS:
<br />A. GENERAL: IN COMPLIANCE WITH SECTION 01 3300 AND AS SPECIFIED HEREIN.
<br />B. PRODUCT DATA: SUBMIT MANUFACTURER'S PRODUCT LITERATURE AND INSTALLATION
<br />INSTRUCTIONS FOR EACH TYPE OF CUBICLE CURTAIN TRACK, CURTAIN AND
<br />INSTALLATION ACCESSORY REQUIRED. INCLUDE METHODS OF INSTALLATION FOR EACH
<br />TYPE OF SUPPORTING STRUCTURE.
<br />1.3 QUALITY ASSURANCE:
<br />A. MANUFACTURER QUALIFICATIONS: FABRICATOR WITH NOT LESS THAN 3 YEARS OF
<br />PRODUCTION EXPERIENCE WITH CUBICLE CURTAIN TRACK, CURTAIN SIMILAR TO
<br />REQUIREMENTS OF THIS PROJECT.
<br />B. INSTALLER QUALIFICATIONS: FIRM SPECIALIZING IN CUBICLE CURTAIN TRACKS WITH NOT
<br />LESS THAN 2 YEARS OF EXPERIENCE IN INSTALLATION OF PRODUCTS SIMILAR TO THAT
<br />REQUIRED FOR THIS PROJECT.
<br />1.4 DELIVERY, STORAGE AND HANDLING:
<br />A. COMPLY WITH INSTRUCTIONS AND RECOMMENDATIONS OF MANUFACTURER FOR
<br />SPECIAL DELIVERY, STORAGE, AND HANDLING REQUIREMENTS.
<br />B. DELIVER MATERIAL TO PROJECT SITE ON PROTECTIVE WRAPPINGS AND CONTAINERS,
<br />CLEARLY LABELED WITH IDENTIFICATION OF MANUFACTURER. STORE MATERIALS IN
<br />PACKAGES, INSIDE WELL-VENTILATED AREA PROTECTED FROM WEATHER, MOISTURE,
<br />SOILING, AND TEXTURE TEMPERATURE AND HUMIDITY.
<br />1.5 SEQUENCING AND SCHEDULING:
<br />A. SEQUENCE CUBICLE CURTAIN TRACK, CURTAIN INSTALLATION WITH OTHER WORK TO
<br />MINIMIZE POSSIBILITY OF DAMAGE AND SOILING DURING REMAINDER OF CONSTRUCTION
<br />PERIOD.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS:
<br />A. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE
<br />PRODUCTS OF ONE OF THE FOLLOWING:
<br />1. BASIS OF DESIGN: GENERAL CUBICLE COMPANY, INC.
<br />2. KIRSCH.
<br />3. INPRO CORP.
<br />4. AR NELSON.
<br />2.2 TRACK MATERIALS:
<br />A. PROVIDE CUBICLE CURTAIN TRACK CONFIGURATIONS AS SHOWN ON DRAWINGS,
<br />EQUIPPED WITH HARDWARE AS SCHEDULED.
<br />B. EXTRUDED-ALUMINUM TRACK: NOT LESS THAN 1-1/4" WIDE BY 3/4" HIGH; WITH MINIMUM
<br />WALL THICKNESS OF 0.058".
<br />1. CURVED TRACK: FACTORY FABRICATED 14" RADIUS BENDS.
<br />2. TRACK FINISH: WHITE BAKED ENAMEL.
<br />C. PROVIDE TRACK ACCESSORIES AS REQUIRED.
<br />D. TRACK ACCESSORIES: FABRICATE SPLICES, END CAPS, CONNECTORS, END STOPS,
<br />COUPLING AND JOINING SLEEVES, WALL FLANGES, BRACKETS, CEILING CLIPS, AND
<br />OTHER ACCESSORIES FROM SAME MATERIAL AND WITH SAME FINISH AS TRACK.
<br />1. SUSPENDED TRACK SUPPORT: NOT LESS THAN 7/8" O.D. TUBE.
<br />2. END STOP: REMOVABLE WITH CARRIER HOOK.
<br />3. SPLICING CLAMP: ANODIZED SLEEVE SECURING JOINED SECTIONS OF TRACK.
<br />4. CURVES: TRACK CHANNEL BENT TO 12" RADIUS.
<br />5. SPLICE LOCATIONS: PROVIDE CONTINUOUS TRACK ASSEMBLIES WITHOUT
<br />SPLICES WHEREVER POSSIBLE. WHERE SPLICES ARE UNAVOIDABLE, LOCATE
<br />SPLICES NO CLOSER THAN 12" FROM THE END OF A CURVED SECTION, NOR
<br />CLOSER THAN 12" TO THE END OF THE TRACK.
<br />6. ROLLER CARRIER: BASIS OF DESIGN IS GENERAL IFC-100.
<br />7. CURTAIN ACCESSORIES: PROVIDE TRACK ACCESSORIES TO FACILITATE USE OF
<br />CURTAINS.
<br />2.3 CUBICLE CURTAINS:
<br />A. CUBICLE CURTAIN:
<br />1. BASIS OF DESIGN: ICP MEDICAL
<br />2. ALTERNATE: OWNER APPROVED EQUAL.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION:
<br />A. EXAMINE AREAS AND CONDITIONS WHERE CURTAIN TRACK, CURTAIN WILL BE
<br />INSTALLED. DO NOT PROCEED UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED. ONCE THE CONTRACTOR ACCEPTS AND COMMENCES THE INSTALLATION
<br />IN A ROOM OR AREA, THE CONTRACTOR SHALL REPAIR AND CORRECT DAMAGES TO THE
<br />BUILDING CONSTRUCTION RESULTING FROM HIS INSTALLATION OPERATIONS.
<br />3.2 PREPARATION:
<br />A. PRIOR TO INSTALLATION OF CUBICLE CURTAIN TRACK AND CURTAINS, CLEAN
<br />SUBSTRATE TO REMOVE DUST, DEBRIS, AND LOOSE PARTICLES.
<br />B. COORDINATE MOUNTING OF TRACK WITH REFLECTED CEILING PLAN TO AVOID CONFLICT
<br />WITH LIGHTS, AND OTHER CEILING MOUNTED DEVICES.
<br />C. VERIFY THAT MATERIALS ARE THOSE SPECIFIED BEFORE INSTALLING.
<br />3.3 INSTALLATION:
<br />A. INSTALL CUBICLE CURTAIN TRACK, CURTAIN UNITS IN MANNER INDICATED TO COMPLY
<br />WITH FABRICATOR'S INSTRUCTIONS. SECURE AT PROPER HEIGHT AND LOCATION
<br />RELATIVE TO ADJOINING RELATED WORK. SECURELY ANCHOR UNITS WITH PROPER
<br />ANCHORAGES, SUITED TO CEILING LEVEL, SURFACE MOUNTING.
<br />B. SECURE TRACK TO CEILING WITH FASTENERS APPROPRIATE FOR SUBSTRATE AT
<br />MINIMUM 3'-0" INTERVALS. PROVIDE TRACK ACCESSORIES AS REQUIRED.
<br />C. MAKE PROVISIONS FOR UNENCUMBERED OPERATION OF HARDWARE.
<br />3.4 FIELD QUALITY CONTROL:
<br />A. TEST OPERATION OF EACH CUBICLE CURTAIN TRACK, CURTAIN AND ADJUST THOSE
<br />WHICH DO NOT OPERATE SMOOTHLY.
<br />3.5 ADJUSTING:
<br />A. RETURN TO PROJECT SITE 6 MONTHS AFTER THE ARCHITECT'S FINAL CERTIFICATE, RE-
<br />HANG ANY CUBICLE CURTAIN UNITS WHICH REQUIRE MINOR ADJUSTMENT; RE-HEM
<br />CUBICLE CURTAIN UNITS WHICH HAVE STRETCHED.
<br />3.6 CLEANING AND PROTECTION:
<br />A. REMOVE SURPLUS MATERIALS, RUBBISH, AND DEBRIS RESULTING FROM INSTALLATION
<br />UPON COMPLETION OF WORK, AND LEAVE AREAS OF INSTALLATION IN NEAT, CLEAN
<br />CONDITION.
<br />B. PROTECT TESTED AND INSTALLED UNITS TO ENSURE OPTIMUM OPERATING CONDITIONS
<br />WITHOUT DAMAGE, BLEMISHES OR INDICATION OF USE AT COMPLETION OF PROJECT.
<br />REPAIR OR REPLACE DAMAGED, SOILED OR OTHERWISE DEFECTED UNITS.
<br />END OF SECTION
<br />SECTION 10 2600 - WALL PROTECTION
<br />PART 1 - GENERAL
<br />1.1 SUMMARY:
<br />A. WORK OF THIS SECTION INCLUDES:
<br />1. WALL PROTECTION
<br />B. RELATED WORK SPECIFIED ELSEWHERE: GYPSUM BOARD.
<br />1.2 REFERENCES:
<br />A. ASTM INTERNATIONAL (ASTM)
<br />B. INTERNATIONAL BUILDING CODE (IBC)
<br />C. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA); LIFE SAFETY CODE.
<br />D. UNDERWRITERS LABORATORIES (UL).
<br />1.3 ACTION SUBMITTALS:
<br />A. PRODUCT DATA: SUBMIT PRODUCT DATA AND DETAILED SPECIFICATIONS FOR EACH
<br />SYSTEM COMPONENT AND INSTALLATION ACCESSORY REQUIRED, INCLUDING
<br />INSTALLATION METHODS FOR EACH TYPE OF SUBSTRATE.
<br />B. SAMPLES: SAMPLES FOR VERIFICATION PURPOSES: SUBMIT 12" LONG SAMPLE OF EACH
<br />MODEL SPECIFIED AND AS PROPOSED FOR THIS WORK, FOR VERIFICATION OF GUARD.
<br />1.4 QUALITY ASSURANCE:
<br />A. INSTALLER QUALIFICATIONS: ENGAGE AN INSTALLER WHO HAS NO LESS THAN 3 YEARS
<br />EXPERIENCE IN INSTALLATION OF SYSTEMS SIMILAR IN COMPLEXITY TO THOSE
<br />REQUIRED FOR THIS PROJECT.
<br />B. MANUFACTURER'S QUALIFICATIONS: NOT LESS THAN 5 YEARS EXPERIENCE IN THE
<br />PRODUCTION OF SPECIFIED PRODUCTS AND A RECORD OF SUCCESSFUL IN-SERVICE
<br />PREFORMANCE.
<br />C. CODE COMPLIANCE: ASSEMBLIES SHALL CONFORM TO APPLICABLE CODES INCLUDING
<br />IBC, AND LIFE SAFETY.
<br />D. FIRE PERFORMANCE CHARACTERISTICS: PROVIDE WALL PROTECTION SYSTEM
<br />COMPONENTS WITH UL LABEL INDICATING THAT THEY ARE IDENTICAL TO THOSE TESTED
<br />IN ACCORD WITH ASTM E84-12A FOR CLASS 1 CHARACTERISTICS LISTED BELOW"
<br />1. FLAME SPREAD: 25 OR LESS
<br />2. SMOKE DEVELOPED: 450 OR LESS.
<br />E. IMPACT STRENGTH: PROVIDE ASSEMBLED WALL PROTECTION UNITS THAT HAVE BEEN
<br />TESTED IN ACCORD WITH THE APPLICABLE PROVISIONS OF ASTM F476-84(2002)
<br />F. CHEMICAL AND STAIN RESISTANCE: PROVIDE WALL PROTECTION SYSTEM COMPONENTS
<br />WITH CHEMICAL AND STAIN RESISTANCE IN ACCORDANCE WITH ASTM D1308-02(2007).
<br />G. COLOR MATCH: PROVIDE WALL PROTECTION COMPONENTS THAT ARE COLOR MATCHED
<br />IN ACCORDANCE WITH THE FOLLOWING:
<br />1. DELTA ECMC OF NO GREATER THAN 1.0 USING CIELAB COLOR SPACE.
<br />H. SINGLE SOURCE RESPONSIBILITY: PROVIDE ALL COMPONENTS OF THE WALL
<br />PROTECTION SYSTEM MANUFACTURED BY THE SAME COMPANY TO ENSURE
<br />COMPATIBILITY OF COLOR, TEXTURE AND PHYSICAL PROPERTIES.
<br />1.5 DELIVERY, STORAGE AND HANDLING:
<br />A. DELIVER MATERIALS TO THE PROJECT SITE IN UNOPENED ORIGINAL FACTORY
<br />PACKAGING CLEARLY LABELED TO SHOW MANUFACTURER.
<br />B. STORE MATERIALS IN ORIGINAL, UNDAMAGED PACKAGING IN A COOL, DRY PLACE OUT
<br />OF DIRECT SUNLIGHT AND EXPOSURE TO THE ELEMENTS. MAINTAIN A MINIMUM ROOM
<br />TEMPERATURE OF 40 DEGREES F. AND A MAXIMUM TEMPERATURE OF 100 DEGREES F.
<br />C. STORE MATERIAL FLAT.
<br />1.6 PROJECT CONDITIONS:
<br />A. ACCLIMATE MATERIALS IN AN ENVIRONMENT OF 65 DEGREES TO 75 DEGREES FOR AT
<br />LEAST 24 HOURS PRIOR TO BEGINNING INSTALLATION.
<br />B. INSTALLATION AREAS SHALL BE ENCLOSED AND WEATHERPROOFED BEFORE
<br />INSTALLATION COMMENCES.
<br />PART 2 - PRODUCTS
<br />2.1 CORNER GUARDS:
<br />A. ENGINEERING PETG: HIGH IMPACT ACROVYN 4000 WITH NOMINAL .040" THICKNESS.
<br />B. ALUMINUM EXTRUSIONS: ALLOY AND TEMPER RECOMMENDED BY MANUFACTURER
<br />FOR TYPE OF USE AND FINISH INDICATED, BUT WITH NOT LESS THAN STRENGTH AND
<br />DURABILITY PROPERTIES SPECIFIED IN ASTM B221-12A FOR ALLOY 6063-T5.
<br />C. FASTENERS: ALUMINUM, NONMAGNETIC STAINLESS-STEEL, OR OTHER NONCORROSIVE
<br />METAL SCREWS, BOLTS, AND OTHER FASTENERS COMPATIBLE WITH ITEMS BEING
<br />FASTENED. USE SECURITY-TYPE FASTENERS WHERE EXPOSED TO VIEW.
<br />D. ADHESIVE: AS RECOMMENDED BY IMPACT-RESISTANT PLASTIC WALL PROTECTION
<br />MANUFACTURER'S PRODUCT DATA AND WITH A VOC CONTENT LESS THAN THE CURRENT
<br />VOC CONTENT LIMITS OF SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD)
<br />RULE #1113, ARCHITECTURAL COATINGS, RULES IN EFFECT JANUARY 1, 2004.
<br />E. REFER TO FINISH SCHEDULE.
<br />2.2 FABRICATION:
<br />A. FABRICATE IMPACT-RESISTANT WALL PROTECTION UNITSTO COMPLY WITH
<br />REQUIREMENTS INDICATED FOR DESIGN, DIMENSIONS, AND MEMBER SIZES,
<br />INCLUDING THICKNESSES OF COMPONENTS.
<br />B. ASSEMBLE COMPONENTS IN FACTORY TO GREATEST EXTENT POSSIBLE TO MINIMIZE
<br />FIELD ASSEMBLY. DISASSEMBLE ONLY AS NECESSARY FOR SHIPPING AND HANDLING.
<br />C. FABRICATE COMPONENTS WITH TIGHT SEAMS AND JOINTS WITH EXPOSED EDGES
<br />ROLLED. PROVIDE SURFACES FREE OF WRINKLES, CHIPS, DENTS, UNEVEN COLORATION,
<br />AND OTHER IMPERFECTIONS. FABRICATE MEMBERS AND FITTINGS TO PRODUCE FLUSH,
<br />SMOOTH, AND RIGID HAIRLINE JOINTS.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION:
<br />A. EXAMINE SUBSTRATES AND WALL AREAS, WITH INSTALLER PRESENT, FOR
<br />COMPLIANCE WITH REQUIREMENTS FOR INSTALLATION TOLERANCES AND OTHER
<br />CONDITIONS AFFECTING PERFORMANCE OF WORK.
<br />B. PROCEED WITH INSTALLATION ONLY AFTER UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED.
<br />3.2 PREPARATION:
<br />A. COMPLETE FINISHING OPERATIONS, INCLUDING PAINTING , BEFORE INSTALLING
<br />IMPACT-RESISTANT WALL PROTECTION SYSTEM COMPONENTS.
<br />B. BEFORE INSTALLATION, CLEAN SUBSTRATE TO REMOVE DUST, DEBRIS, AND LOOSE
<br />PARTICLES.
<br />3.3 INSTALLATION:
<br />A. GENERAL: INSTALL IMPACT-RESISTANCE HANDRAILS UNITS LEVEL, PLUMB, AND TRUE
<br />TO LINE WITHOUT DISTORTIONS. DO NOT USE MATERIALS WITH CHIPS, CRACKS, VOIDS,
<br />STAINS, OR OTHER DEFECTS THAT MIGHT BE VISIBLE IN THE FINISHED WORK.
<br />3.4 CLEANING:
<br />A. IMMEDIATELY AFTER COMPLETION OF INSTALLATION, CLEAN PLSTIC COVERS AND
<br />ACCESSORIES USING A STANDARD, AMMONIA-BASED, HOUSEHOLD CLEANING AGENT.
<br />B. REMOVE EXCESS ADHESIVE USING METHODS AND MATERIALS RECOMMENDED IN
<br />MANUFACTURER'S PRODUCT DATA.
<br />END OF SECTION
<br />DIVISION 11 THRU 21
<br />(NO SECTIONS REQUIRED)
<br />DIVISION 22
<br />PROVIDED ON PLUMBING DRAWINGS
<br />DIVISION 23
<br />PROVIDED ON MECHANICAL DRAWINGS
<br />DIVISION 24
<br />(NO SECTIONS REQUIRED)
<br />DIVISION 25
<br />(NO SECTIONS REQUIRED)
<br />DIVISION 26
<br />PROVIDED ON ELECTRICAL DRAWINGS
<br />DIVISION 27 THRU 49
<br />(NO SECTIONS REQUIRED)
<br />R
<br />No.
<br />F
<br />LICENSE
<br />STATE
<br />D
<br />O
<br />A RCHITECT
<br />C AL IFORNIA
<br />STEPHE WHITE
<br />RENEWAL
<br />DATE
<br />C-34829
<br />N
<br />08/31/25
<br />SHEET TITLE
<br />PROJECT
<br />FACILITY
<br />FAC NO: BLDG NO:FLOOR LEV:SECTION:
<br />KP PROJ. NO.
<br />MATTERPORT LINK: https://my.matterport.com/show/?m=FW21iEbmuii
<br />555 W. Fifth Street Suite 2950 | Los Angeles, CA 90013 USA
<br />ARCHITECT
<br />CONSULTANT
<br />ARCHITECT SEAL CONSULTANT SEAL
<br />KAISER FOUNDATION HOSPITALS
<br />NATIONAL FACILITIES SERVICES
<br />1800 HARRISON STREET OAKLAND,
<br />CALIFORNIA 94612
<br />ISSUE / REVISION LOG
<br />NO. ISSUED DATE
<br />0
<br />5'
<br />50
<br />'
<br />GR
<br />A
<br />P
<br />H
<br />I
<br />C
<br />
<br />S
<br />C
<br />A
<br />L
<br />E
<br />S
<br />:
<br />1/
<br />1
<br />6
<br />"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />0
<br />25
<br />'
<br />1/
<br />8
<br />"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />5'
<br />0
<br />12
<br />'
<br />1/
<br />4
<br />"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />1'
<br />0
<br />6'
<br />1/
<br />2
<br />"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />1'
<br />0
<br />2'
<br />1-
<br />1
<br />/
<br />2
<br />"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />0
<br />1'
<br />3"
<br />
<br />=
<br />
<br />1
<br />'
<br />-
<br />0
<br />"
<br />IF
<br />
<br />T
<br />H
<br />I
<br />S
<br />
<br />S
<br />H
<br />E
<br />E
<br />T
<br />
<br />I
<br />S
<br />
<br />N
<br />O
<br />T
<br />
<br />30
<br />"
<br />x
<br />4
<br />2
<br />"
<br />,
<br />
<br />I
<br />T
<br />
<br />I
<br />S
<br />
<br />A
<br />
<br />R
<br />E
<br />D
<br />U
<br />C
<br />E
<br />D
<br />
<br />PR
<br />I
<br />N
<br />T
<br />
<br />-
<br />
<br />S
<br />C
<br />A
<br />L
<br />E
<br />
<br />AC
<br />C
<br />O
<br />R
<br />D
<br />I
<br />N
<br />G
<br />L
<br />Y
<br />AGENCY APPLICATION NUMBER
<br />AGENCY APPROVAL STAMP
<br />THIS DOCUMENT IS THE PROPERTY OF THE OWNER AND IS
<br />NOT TO BE USED WITHOUT OWNER'S WRITTEN PERMISSION.
<br />HZ PROJ. NO.
<br />Phone 310.820.4600 | Fax 310.207.4215
<br />www.huitt-zollars.com
<br />C:\Users\jpark\Documents\R314412.44 - KP SAN 1st Flr Gen Rad_A22_Central_jhaLWMQW.rvt
<br />5/20/2024 10:23:29 AM
<br />SOCC 2023 R RAD SAN 1ST FLOOR
<br />GEN RAD REPLACEMENT (5284)
<br />G0-04
<br />SPECIFICATIONS
<br />CA361 1
<br />CAP028060R314412.44
<br />SANTA ANA MEDICAL OFFICES
<br />1900 E. 4TH ST.
<br />SANTA ANA, CA 92701
<br />CITY SUBMITTAL 04/19/2024
<br />BID SET 05/20/2024
<br />1900 E 4th St -
<br />1011190678/9/2024
|