|
1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />THE GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL ALL CEILING
<br />ACCESS PANELS IN GYPSUM BOARD CEILINGS AS REQUIRED FOR
<br />MECHANICAL, ELECTRICAL AND PLUMBING ACCESS PER LOCAL CODES,
<br />WHETHER INDICATED ON DRAWINGS OR NOT. COORDINATE LOCATIONS SIZE
<br />AND TYPE WITH ARCHITECT PRIOR TO INSTALLATION.
<br />PRIOR TO CLOSING UP AND SEALING, ALL PLENUM SYSTEMS (HVAC,
<br />PLUMBING, ELECTRICAL, ETC.) SHALL BE INSPECTED AND WHERE REQUIRED,
<br />TESTED BY CONTRACTOR'S ENGINEERS, TO INSURE THEIR PROPER
<br />INSTALLATION AND FUNCTION.
<br />CEILING IN CLOSETS SHALL BE OF THE SAME HEIGHTS AND CONSTRUCTION
<br />AS THAT OF ADJOINING SPACE, EXCEPT AS OTHERWISE NOTED.
<br />THE GENERAL CONTRACTOR SHALL PROVIDE CUT-OUTS AND OTHER SPECIAL
<br />PROVISIONS IN ACOUSTICAL WORK AS REQUIRED FOR LIGHTING FIXTURES,
<br />REGISTERS, AND DIFFUSERS AND OTHER INSERTED ITEMS.
<br />ALL DOWNLIGHTS, WALL WASHERS, SPRINKLER HEADS, ETC., SHALL ALIGN IN
<br />STRAIGHT LINE, UNLESS OTHERWISE NOTED.
<br />FASCIAS OR ANY BREAK IN THE CEILING HEIGHTS SHALL BE AS SHOWN ON
<br />DRAWINGS AND SHALL BE FORMED OF GYPSUM WALLBOARD ON TYPICAL
<br />PROJECT FRAMING TYPE.
<br />CEILING HEIGHTS SHALL BE AS SHOWN ON DRAWINGS AND DETAILS. ANY
<br />DEVIATION FROM HEIGHTS SHOWN BASED UPON EXISTING FIELD CONDITIONS
<br />SHALL BE SUBMITTED TO ARCHITECT FOR REVIEW PRIOR TO START OF WORK
<br />IN QUESTION, OR RELATED WORK.
<br />ALL SPRINKLERS IN DRYWALL CEILING AREAS SHALL HAVE CONCEALED HEAD
<br />ASSEMBLIES. COLOR OF TRIM SHALL MATCH ADJACENT CEILING.
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />WALLCOVERING SUBCONTRACTOR TO REVIEW PERTINENT WALL PATCHING
<br />NOTES IN "PATCHING AND CUTTING ” ON THIS SHEET, AND ENSURE SURFACES
<br />ARE PROPERLY PREPPED PRIOR TO COMMENCING WORK.
<br />WALLS SHALL INCLUDE SURFACES FROM FLOOR TO CEILING, INCLUDING
<br />PILASTERS, FASCIAS AND ALL VERTICAL SURFACES NOT INCLUDED IN
<br />CEILING, UNLESS OTHERWISE NOTED.
<br />THE GENERAL CONTRACTOR SHALL SUBMIT THREE (3) SAMPLES 12 X 12 OF
<br />EACH FINISH FOR REVIEW BY ARCHITECT. THIS INCLUDES, BUT IS NOT
<br />LIMITED TO ALL PAINT, WALLCOVERING, ETC.
<br />ALL WALLS AND CEILINGS SHALL BE PROPERLY PREPARED, PATCHED,
<br />SANDED, ETC., TO PROVIDE A LEVEL 4 FINISH. PROVIDE LEVEL 5 FINISH ONLY
<br />WHERE INDICATED ON PLAN.
<br />THE CONTRACTOR SHALL REMOVE ALL ELECTRICAL SWITCH PLATES AND
<br />OUTLET PLATES, SURFACE HARDWARE, ETC., PRIOR TO PAINTING,
<br />PROTECTING AND REPLACING SAME WHEN PAINTING HAS BEEN COMPLETED.
<br />HE SHALL REMOVE ALL PAINT FROM WHERE IT HAS SPILLED, SPLASHED OR
<br />SPLATTERED ON SURFACES, INCLUDING BUT NOT LIMITED TO LIGHT
<br />FIXTURES, DIFFUSERS, REGISTERS, ETC.
<br />EXISTING LOOSE PAINT SHALL BE REMOVED AND THE SURFACE SANDED
<br />SMOOTH TO RECEIVE NEW FINISH.
<br />UNEVENNESS IN EXISTING PARTITIONS SHALL BE SANDED OR CHIPPED AWAY
<br />AND SURFACES PATCHED TO INSURE A PERFECTLY EVEN SURFACE.
<br />THE CONTRACTOR SHALL EXAMINE ALL AREAS OF CONSTRUCTION AFTER
<br />COMPLETION OF WORK BY ALL TRADES (INCLUDING TELEPHONE
<br />INSTALLATION, FLOORING, ETC.) AND COMPLETE ALL NECESSARY “TOUCH-
<br />UP” PAINTING AND/OR PATCHING PRIOR TO SCHEDULING A PUNCH-WALK.
<br />IT IS THE INTENT OF THE DRAWINGS THAT ALL EXPOSED SURFACES RECEIVE
<br />FINISHES UNLESS SPECIFICALLY NOTED OTHERWISE ON THE DRAWINGS. ANY
<br />SURFACES WHICH DO NOT HAVE A SPECIFIC FINISH NOTED, OR ARE NOTED
<br />TO REMAIN UNFINISHED, SHALL BE BROUGHT TO THE ATTENTION OF THE
<br />ARCHITECT AND FINISHED PER ARCHITECT'S INSTRUCTIONS.
<br />09 WALL FINISHES
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />10.
<br />GENERAL CONTRACTOR SHALL SUBMIT ALL REQUESTED FABRICATION
<br />SHOP DRAWINGS, SAMPLES AND FIXTURE CUTS TO ARCHITECT FOR
<br />REVIEW. DIGITAL PDF FILES SHALL BE SUBMITTED FOR DRAWINGS AND
<br />FIXTURE CUTS. ALL SHOP DRAWINGS AND CUT SHEETS SIGNED
<br />“REVIEWED ” SHALL SUPERSEDE ORIGINAL DRAWINGS IN DESIGN
<br />APPEARANCE ONLY. SUBCONTRACTORS SHALL ASSUME RESPONSIBILITY
<br />FOR ERRORS IN THEIR DRAWINGS.
<br />GENERAL CONTRACTOR SHALL REVIEW SUBCONTRACTOR(S) SUBMITTED
<br />DRAWINGS AND DATA, VERIFY FIELD MEASUREMENTS, APPLY REVIEW
<br />STAMP AND SUBMIT TO ARCHITECT PROMPTLY.
<br />GENERAL CONTRACTOR SHALL INDICATE ON REVIEW STAMP THAT THE
<br />CONTRACTOR HAS REVIEWED SUBCONTRACTOR(S) SUBMITTAL FOR
<br />CONFORMANCE TO THE SPECIFIED PRODUCT.
<br />GENERAL CONTRACTOR SHALL DISAPPROVE AND RETURN TO
<br />SUBCONTRACTOR ANY SUBMITTALS NOT MEETING THE REQUIREMENTS OF
<br />THE CONTRACT DOCUMENTS. GENERAL CONTRACTOR SHALL MAINTAIN AN
<br />UP-TO-DATE SUBMITTAL LOG, AND DISTRIBUTE THE LOG WEEKLY.
<br />THE ARCHITECT WILL REVIEW AND EITHER ACCEPT OR REJECT, WITH
<br />REASONABLE PROMPTNESS AND AS OUTLINED IN THE ACCEPTED
<br />SUBMITTAL SCHEDULE, DATA AND DRAWINGS SUBMITTED BY THE
<br />CONTRACTOR. THE ARCHITECT WILL REVIEW SUBMITTALS FOR
<br />CONFORMANCE WITH THE INTENT OF THE DESIGN, AND FOR COMPLIANCE
<br />WITH SPECIFIC AND RELEVANT REQUIREMENTS OF THE CONTRACT
<br />DOCUMENTS.
<br />THE ARCHITECT WILL REJECT AND RETURN TO THE CONTRACTOR, SHOP
<br />DRAWINGS AND PROJECT LITERATURE SUBMITTED WITHOUT THE
<br />CONTRACTOR(S) REVIEW STAMP AND/OR NOT THOROUGHLY REVIEWED BY
<br />THE CONTRACTOR PRIOR TO SUBMITTAL.
<br />THE ARCHITECT IS NOT RESPONSIBLE FOR DELAYS CAUSED BY REJECTION
<br />OF SHOP DRAWINGS SUBMITTED BY THE CONTRACTOR.
<br />REVIEW WILL NOT RELIEVE THE CONTRACTOR FROM RESPONSIBILITY FOR
<br />ERRORS.
<br />REVIEW OF SUBMITTALS BY THE ARCHITECT SHALL NOT BE CONSTRUED AS
<br />AUTHORIZING CHANGES IN THE CONTRACT SUM OR CONTRACT TIME, NOR
<br />SHALL IT BE CONSTRUED AS RELIEVING THE CONTRACTOR OF HIS
<br />RESPONSIBILITY FOR COORDINATION OF WORK WITH OTHER TRADES, OR
<br />INTERPRETED AS APPROVING QUANTITIES AND DIMENSIONS.
<br />THE ARCHITECTS REVIEW OF SUBMITTALS OR DATA SHALL NOT RELIEVE
<br />THE CONTRACTOR FROM RESPONSIBILITY FOR DEVIATIONS FROM
<br />CONTRACT DRAWINGS OR SPECIFICATIONS UNLESS THE CONTRACTOR
<br />HAS CALLED THE ARCHITECTS AND OWNER ’S ATTENTION TO SUCH
<br />DEVIATIONS AND SECURED WRITTEN ACCEPTANCE, NOR SHALL IT RELIEVE
<br />HIM OF RESPONSIBILITY FOR ERRORS IN SHOP DRAWINGS OR OTHER DATA.
<br />SUBMITTAL PROCEDURES
<br />1.
<br />2.
<br />3.
<br />THE HVAC CONTRACTOR SHALL BE RESPONSIBLE FOR FIELD SUPERVISION
<br />OF ALL THEIR WORK DURING INSTALLATION AND SHALL INSPECT ALL
<br />SYSTEMS FOR PROPER OPERATIONS AT COMPLETION OF JOB.
<br />INSTALLATION SHALL BE COORDINATED WITH ALL TRADES AS REQUIRED FOR
<br />PROPER ASSEMBLY. CEILING DIFFUSERS TO BE RELOCATED TO
<br />ACCOMMODATE NEW LIGHT FIXTURE PATTERNS.
<br />INTERIOR SPACES SHALL BE MECHANICALLY VENTILATED IN ACCORDANCE
<br />WITH APPLICABLE CODES.
<br />23 MECHANICAL
<br /> SUBMITTAL & SHOP DRAWING LIST (MIN.)
<br />1.
<br />2.
<br />ROOF SCREEN
<br />PAINT
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />THE GENERAL CONTRACTOR SHALL FURNISH ALL LABOR AND MATERIALS AS
<br />REQUIRED TO COMPLETE DEMOLITION AND REMOVAL OF ALL ITEMS
<br />INDICATED IN DRAWINGS OR AS OTHERWISE DIRECTED BY ARCHITECT.
<br />THE GENERAL CONTRACTOR SHALL FURNISH OWNER WITH A COMPLETE
<br />INVENTORY LIST OF ALL ITEMS THAT CAN BE REUSED AND/OR STORED IN
<br />BUILDING STOCK, OBTAIN DIRECTIVE REGARDING THEIR DISPOSITION.
<br />THE GENERAL CONTRACTOR SHALL EXECUTE ALL WORK WITHIN THE
<br />REGULATION OF PROPERTY MANAGEMENT, CLIENT AND/OR OWNER FOR
<br />DEMOLITION AND REMOVAL OF DEBRIS, INCLUDING AFTER HOURS WORK, AS
<br />MAY BE REQUIRED.
<br />ALL WORK DEMOLISHED SHALL BE REMOVED FROM THE PREMISES, EXCEPT
<br />ITEMS TO BE REUSED OR RETURNED TO OWNER OR AS OTHERWISE NOTED.
<br />THE GENERAL CONTRACTOR SHALL REMOVE ALL RUBBISH AND WASTE
<br />MATERIALS, BOTH FROM HIS OWN AND OTHER SUBCONTRACTORS
<br />EMPLOYEES, AND PROVIDE FOR ITS REMOVAL FROM THE SITE.
<br />THE GENERAL CONTRACTOR SHALL REMOVE FROM PREMISES ALL
<br />CONDUITS, BOXES, PLATES, BRIDGED OR ANY OTHER TELEPHONE AND/OR
<br />ELECTRICAL WIRING AND EQUIPMENT LEFT AFTER WALL DEMOLITION.
<br />THE GENERAL CONTRACTOR SHALL PROVIDE A VISQUEEN SEAL FROM FLOOR
<br />TO CEILING AT ALL INTERFACES TO PROTECT ADJACENT BUILDING PROPERTY
<br />WHILE DEMOLITION AND CONSTRUCTION ARE IN PROGRESS. THIS SEAL IS TO
<br />BE KEPT CLOSED AT ALL TIMES.
<br />THE GENERAL CONTRACTOR SHALL CAP AND FLUSH OFF BEHIND FINISHED
<br />SURFACES ALL PROJECTING PLUMBING, FLOOR ELECTRICAL/TELEPHONE
<br />OUTLETS, AND ALL OTHER PROJECTING ITEMS WHICH ARE BEING
<br />ABANDONED.
<br />UPON COMPLETION OF THE DEMOLITION WORK, THE GENERAL CONTRACTOR
<br />SHALL ENSURE THAT ALL AREAS ARE LEFT BROOM CLEAN.
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />THE GENERAL CONTRACTOR SHALL DO ALL CUTTING, FITTING AND PATCHING
<br />WORK THAT MAY BE REQUIRED TO MAKE ALL PARTS COME TOGETHER
<br />PROPERLY, AND FIT TO RECEIVE OR BE RECEIVED BY WORK OF OTHER
<br />CONTRACTORS WHERE SHOWN, OR REASONABLY IMPLIED BY THE DRAWINGS
<br />AND NOTES.
<br />THE GENERAL CONTRACTOR SHALL PROVIDE ALL FLOOR CUT-OUTS AND
<br />PATCHING REQUIRED FOR THE INSTALLATION OF ALL WORK.
<br />THE GENERAL CONTRACTOR SHALL SURVEY ALL EXISTING FINISHED
<br />SURFACES TO REMAIN FOR CHIPS, CRACKS, HOLES, AND OTHER DAMAGE.
<br />THESE DEFECTIVE SURFACES SHALL BE REPAIRED OR IF BEYOND REPAIRING,
<br />THEN THE GENERAL CONTRACTOR SHALL REMOVE ALL EXISTING AND
<br />REPLACE WITH NEW TO MATCH EXISTING TO THE SATISFACTION OF OWNER
<br />AND TENANT.
<br />THE GENERAL CONTRACTOR SHALL INSPECT ALL EXISTING SURFACES TO
<br />REMAIN, AFTER DEMOLITION OF EXISTING FINISHES, (I.E. WALL COVERING,
<br />WALL BASE, ETC.) IF SURFACE IS NOT SMOOTH AND FLUSH TO RECEIVE NEW
<br />FINISH, SUBCONTRACTOR SHALL SKIM COAT AND SAND SMOOTH.
<br />IN ALL AREAS WHERE DEMOLITION CAUSES AN UNEVENNESS IN SLAB OR
<br />LIGHTWEIGHT CONCRETE, THE CONTRACTOR SHALL PATCH TO LEVEL AS
<br />REQUIRED TO RECEIVE NEW FLOORING FINISH.
<br />ALL EXISTING OR NEW CONSTRUCTION WORK SHOWN ON DRAWINGS THAT IS
<br />DAMAGED AS A RESULT OF WORK FOR THIS PROJECT SHALL BE PATCHED AS
<br />REQUIRED TO MATCH IMMEDIATE EXISTING ADJACENT AREAS IN MATERIALS,
<br />FIRE RATING, FINISH AND COLOR, UNLESS OTHERWISE NOTED.
<br />CONTRACTOR TO DOWEL/FILL/PATCH SLAB AFTER SAWCUTTING TO ENSURE
<br />SLAB STRUCTURAL INTEGRITY.
<br />THE GENERAL CONTRACTOR SHALL PATCH ALL CRACKS, HOLES OR OTHER
<br />IMPERFECTIONS (PROJECTIONS SHALL BE REMOVED AND PATCHED) TO
<br />PROVIDE A CONTINUOUS SMOOTH FLOOR SURFACE.
<br />THE GENERAL CONTRACTOR SHALL NOTIFY ARCHITECT AFTER FLOOR
<br />PATCHING IS DONE AND RECEIVE THEIR REVIEW PRIOR TO INSTALLATION OF
<br />FINISHED FLOORING.
<br />PATCHING AND CUTTING
<br />09 PAINT
<br />A.
<br />A.
<br />1.
<br />2.
<br />A.
<br />B.
<br />1.
<br />2.
<br />A.
<br />B.
<br />A.
<br />B.
<br />C.
<br />1.
<br />2.
<br />A.
<br />A.
<br />1.
<br />2.
<br />3.
<br />A.
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />A.
<br />B.
<br />1.
<br />2.
<br />3.
<br />A.
<br />B.
<br />C.
<br />D.
<br />1.
<br />2.
<br />3.
<br />4.
<br />A.
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />10.
<br />11.
<br />B.
<br />C.
<br />D.
<br />E.
<br />1.
<br />2.
<br />3.
<br />F.
<br />1.
<br />2.
<br />G.
<br />H.
<br />PART 1 - GENERAL
<br />1.1 RELATED DOCUMENTS
<br />DRAWINGS AND GENERAL PROVISIONS OF THE CONTRACT, INCLUDING
<br />GENERAL AND SUPPLEMENTARY CONDITIONS AND DIVISION 1 SPECIFICATION
<br />SECTIONS, APPLY TO THIS SECTION.
<br />1.2 SUMMARY
<br />THIS SECTION INCLUDES THE FOLLOWING:
<br />SURFACE PREPARATION.
<br />FIELD APPLICATION OF PAINTS, STAINS, VARNISHES, AND OTHER
<br />COATINGS.
<br />1.3 SUBMITTALS
<br />PRODUCT DATA - SUBMIT PRODUCT DATA SHEETS FOR EACH PRODUCT.
<br />SAMPLES:
<br />SUBMIT TWO PAINTED SAMPLES, ILLUSTRATING SELECTED COLORS AND
<br />TEXTURES FOR EACH COLOR AND SYSTEMS SELECTED WITH SPECIFIED
<br />COATS CASCADED.
<br />SUBMIT ON SUITABLE BACKING, 8X10 INCH SIZE.
<br />1.4 DELIVERY, STORAGE, AND PROTECTION
<br />DELIVER PRODUCTS TO SITE IN SEALED AND LABELED CONTAINERS; INSPECT
<br />TO VERIFY ACCEPTABILITY.
<br />CONTAINER LABEL: INCLUDE MANUFACTURER'S NAME, TYPE OF PAINT,
<br />BRAND NAME, LOT NUMBER, BRAND CODE, COVERAGE, SURFACE
<br />PREPARATION, DRYING TIME, CLEANUP REQUIREMENTS, COLOR
<br />DESIGNATION, AND INSTRUCTIONS FOR MIXING AND REDUCING.
<br />1.5 ENVIRONMENTAL REQUIREMENTS
<br />DO NOT APPLY MATERIALS WHEN SURFACE AND AMBIENT TEMPERATURES
<br />ARE OUTSIDE THE TEMPERATURE RANGES REQUIRED BY THE PAINT
<br />PRODUCT MANUFACTURER.
<br />PROVIDE LIGHTING LEVEL OF 80 FT CANDLES MEASURED MID-HEIGHT AT
<br />SUBSTRATE SURFACE.
<br />ENVIRONMENT REQUIREMENTS:
<br />COMPLY WITH MANUFACTURER'S RECOMMENDATIONS AS TO
<br />ENVIRONMENTAL CONDITIONS UNDER WHICH COATINGS AND COATING
<br />SYSTEMS CAN BE STORED AND APPLIED.
<br />DO NOT PAINT WHEN THERE IS A THREAT OF RAIN WITHIN 24 HOURS OR
<br />WHEN SURFACE OR AIR TEMPERATURES ARE AT OR BELOW 40 DEGREES.
<br />1.6 WARRANTY
<br />INSTALLER WARRANTY: 1 YEAR.
<br />1.7 EXTRA STOCK
<br />PROVIDE FOLLOWING:
<br />MINIMUM 1 GALLON EACH PRODUCT IN ORIGINAL OR NEW 1 GALLON
<br />CANS.
<br />COLOR SPOT EACH LID.
<br />IDENTIFY WITH FORMULA, LOCATION, PRODUCT AND DATE.
<br />PART 2 - PRODUCTS
<br />2.1 MANUFACTURERS
<br />PAINTS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE EITHER
<br />THE NAMED PRODUCT OR AN EQUAL PRODUCT BY ONE OF THE OTHER
<br />MANUFACTURERS SPECIFIED.
<br />SHERWIN WILLIAMS. (BASIS OF DESIGN)
<br />DUNN-EDWARDS.
<br />GLIDDEN (ICI) PAINTS.
<br />FRAZEE PAINT.
<br />VISTA PAINT.
<br />OR EQUAL.
<br />2.2 PAINTS AND COATINGS
<br />READY MIXED, EXCEPT FIELD-CATALYZED COATINGS.
<br />PREPARE PIGMENTS:
<br />TO A SOFT PASTE CONSISTENCY, CAPABLE OF BEING READILY AND
<br />UNIFORMLY DISPERSED TO A HOMOGENOUS COATING.
<br />FOR GOOD FLOW AND BRUSHING PROPERTIES.
<br />CAPABLE OF DRYING OR CURING FREE OF STREAKS OR SAGS.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION
<br />VERIFY THAT SURFACES ARE READY TO RECEIVE WORK AS INSTRUCTED BY
<br />THE PRODUCT MANUFACTURER.
<br />EXAMINE SURFACES SCHEDULED TO BE FINISHED PRIOR TO
<br />COMMENCEMENT OF WORK. REPORT ANY CONDITION THAT MAY
<br />POTENTIALLY AFFECT PROPER APPLICATION. DO NOT PROCEED UNLESS
<br />SUBSTRATE IS SUITABLE.
<br />TEST SHOP-APPLIED PRIMER FOR COMPATIBILITY WITH SUBSEQUENT COVER
<br />MATERIALS.
<br />MEASURE MOISTURE CONTENT OF SURFACES USING AN ELECTRONIC
<br />MOISTURE METER. DO NOT APPLY FINISHES UNLESS MOISTURE CONTENT OF
<br />SURFACES ARE BELOW THE FOLLOWING MAXIMUMS:
<br />PLASTER AND GYPSUM WALLBOARD: 12 PERCENT
<br />MASONRY, CONCRETE, AND CONCRETE UNIT MASONRY: 12 PERCENT
<br />INTERIOR WOOD: 15 PERCENT, MEASURED IN ACCORDANCE WITH
<br />ASTMD4442.
<br />EXTERIOR WOOD: 15 PERCENT, MEASURED IN ACCORDANCE WITH
<br />ASTMD4442.
<br />3.2 PREPARATION OF SURFACE
<br />GENERAL:
<br />CLEAN ALL EXTERIOR WALLS AND SURFACES OF LOOSE AND SCALY
<br />PAINT, DIRT, DUST, CHALK, AND OTHER FOREIGN MATTER BY WATER-
<br />BLASTING USING CARE NOT TO DAMAGE SUBSTRATE FOLLOWED BY
<br />HAND SCRAPING, SANDING OR WIRE BRUSHING AFTER SURFACES ARE
<br />DRY. MILDEW MUST BE TREATED WITH HOUSEHOLD BLEACH SOLUTION
<br />AND RINSED THOROUGHLY.
<br />PATCH, CAULK, SET PROTRUDING NAILS AND REPAIR ALL SURFACES AND
<br />CRACKS WHERE NECESSARY WITH SUITABLE PATCHING MATERIALS AND
<br />SMOOTH OFF TO MATCH ADJACENT SURFACES.
<br />SAND GLOSSY SURFACES TO DULL SURFACE AND REMOVE RESIDUE.
<br />REMOVE MILDEW FROM AFFECTED SURFACES WITH A SOLUTION OF TRI-
<br />SODIUM PHOSPHATE AND BLEACH. RINSE WITH CLEAN WATER AND
<br />ALLOW TO DRY COMPLETELY.
<br />EXISTING SURFACES TO BE RECOATED SHALL BE THOROUGHLY CLEANED
<br />AND DE-GLOSSED BY SANDING OR OTHER MEANS PRIOR TO PRIMING AND
<br />PAINTING. PATCHED AND BARE AREAS SHALL BE SPOT PRIMED WITH THE
<br />SAME PRIMER AS SPECIFIED FOR NEW WORK.
<br />RUSTY METAL: SCRAPE, SAND OR WIRE WHEEL, FEATHERING EDGES TO
<br />SOUND COATING. DUST SURFACES.
<br />TOPCOAT.
<br />REMOVE SOIL AND BODY OILS COMPLETELY FROM SURFACES, INCLUDING
<br />HANDRAILS, DOOR EDGES AND POSTS. TREAT WITH LIQUID SANDPAPER
<br />OR DULL-N-BOND.
<br />REMOVE HARDWARE, ACCESSORIES, PLATES, FIXTURES AND SIMILAR
<br />ITEMS NOT TO BE FINISHED.
<br />REINSTALL AT COMPLETION.
<br />PAINT EDGES OF SINK CUT-OUTS.
<br />GALVANIZED SURFACES: REMOVE ALL OILS AND CONTAMINATION FROM
<br />GALVANIZED SURFACES SCHEDULED TO BE PAINTED BY WASHING WITH A
<br />COMPLIANT SOLVENT WASH.
<br />FERROUS METAL: REMOVE GREASE, RUST, SCALE, DIRT AND DUST FROM
<br />FERROUS METAL SURFACES. PRIMER COAT SHALL BE APPLIED NOT LESS
<br />THAN 30 MINUTES, NOR MORE THAN 3 HOURS AFTER PREPARATION OF
<br />SURFACE.
<br />PRIMED METAL: SAND AND SCRAPE SHOP PRIMED METAL TO REMOVE LOOSE
<br />PRIMER AND RUST. TOUCH-UP BARE, ABRADED AND DAMAGED AREAS WITH
<br />METAL PRIMER. FEATHER EDGES TO MAKE TOUCH-UP PATCHES
<br />INCONSPICUOUS.
<br />WOOD SURFACES:
<br />REMOVE DUST, GRIT AND FOREIGN MATTER FROM WOOD SURFACES.
<br />SAND SURFACES AND DUST CLEAN. SPOT PRIME KNOTS, PITCH STREAKS
<br />AND SAPPY SECTIONS WITH A STAIN BLOCKING PRIMER WHERE
<br />SURFACES ARE TO BE PAINTED. FILL NAIL HOLES, CRACKS AND OTHER
<br />DEFECTS AFTER PRIMING AND SPOT PRIME REPAIRS AFTER PATCHING
<br />MATERIAL HAS FULLY CURED.
<br />WOOD SURFACES WITH PEELING AREAS ARE TO HAVE EDGES OF
<br />BROKEN PAINT FILM SANDED TO A FEATHER EDGE.
<br />BACK PRIME WOOD TRIM. PAINT TOPS, BOTTOMS, EDGES AND CUT-OUTS
<br />OF DOORS.
<br />PLASTER SURFACES:
<br />PLASTER SURFACES SHALL BE DRY AND FREE FROM EFFLORESCENCE,
<br />ENCRUSTATIONS AND FOREIGN MATTER. FILL CRACKS, HOLES AND
<br />IMPERFECTIONS, SMOOTHING REPAIRS TO MATCH ADJACENT TEXTURE.
<br />ALLOW REPAIRS TO FULLY CURE BEFORE PRIMING.
<br />PRIME PLASTER SURFACES WITH SPECIFIED PRIMER. CAULK ALL CRACKS.
<br />GYPSUM BOARD: GYPSUM BOARD SHALL BE DUSTED CLEAN AND FREE FROM
<br />ENCRUSTATIONS AND OTHER FOREIGN MATTER.
<br />PREPARATION OF OTHER SURFACES SHALL BE PERFORMED FOLLOWING
<br />SPECIFIC RECOMMENDATIONS OF THE COATING MANUFACTURER.
<br />A.
<br />B.
<br />C.
<br />D.
<br />E.
<br />F.
<br />G.
<br />H.
<br />I.
<br />J.
<br />A.
<br />A.
<br />1.
<br />2.
<br />B.
<br />1.
<br />2.
<br />3.
<br />A.
<br />B.
<br />1.
<br />2.
<br />C.
<br />1.
<br />2.
<br />3.
<br />4.
<br />A.
<br />1.
<br />2.
<br />B.
<br />1.
<br />2.
<br />C.
<br />1.
<br />2.
<br />D.
<br />1.
<br />2.
<br />E.
<br />1.
<br />2.
<br />A.
<br />1.
<br />2.
<br />B.
<br />1.
<br />2.
<br />C.
<br />1.
<br />2.
<br />D.
<br />1.
<br />2.
<br />E.
<br />1.
<br />2.
<br />F.
<br />1.
<br />2.
<br />G.
<br />1.
<br />2.
<br />H.
<br />1.
<br />2.
<br />A.
<br />3.3 APPLICATION
<br />APPLY PRODUCTS IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.
<br />WHERE ADJACENT SEALANT IS TO BE PAINTED, DO NOT APPLY FINISH
<br />COATS UNTIL SEALANT IS APPLIED.
<br />DO NOT APPLY FINISHES TO SURFACES THAT ARE NOT DRY. ALLOW APPLIED
<br />COATS TO DRY BEFORE NEXT COAT IS APPLIED.
<br />APPLY EACH COAT TO UNIFORM APPEARANCE. APPLY EACH COAT OF PAINT
<br />SLIGHTLY DARKER THAN PRECEDING COAT UNLESS OTHERWISE APPROVED
<br />SAND WOOD SURFACES LIGHTLY BETWEEN COATS TO ACHIEVE REQUIRED
<br />FINISH.
<br />VACUUM CLEAN SURFACES OF LOOSE PARTICLES. USE TACK CLOTH TO
<br />REMOVE DUST PARTICLES JUST PRIOR TO APPLYING NEXT COAT.
<br />STIPPLE ALL EDGES AND CORNERS TO CONCEAL BRUSH MARKS.
<br />PAINT ENTIRE TRIM ELEMENT WITH LIKE COLOR. PAINTING OF FACES ONLY
<br />IS UNACCEPTABLE. TRIM SURFACES MUST BE WRAPPED WITH THE TRIM
<br />COLOR AND NOT "FACED OFF" OR "HOLLYWOODED".
<br />DOORS: PAINT ENTIRE DOOR UNLESS OTHERWISE NOTED, INCLUDING DOOR
<br />TOP AND BOTTOM EDGE SURFACES.
<br />TINTING: TINT EACH PRIMER A LIGHTER SHADE TO FACILITATE
<br />IDENTIFICATION OF EACH COAT WHERE MULTIPLE COATS OF THE SAME
<br />MATERIAL ARE APPLIED. TINT PRIMER TO MATCH THE COLOR OF THE FINISH
<br />COAT, BUT PROVIDE SUFFICIENT DIFFERENCES IN SHADE OF PRIMER TO
<br />DISTINGUISH EACH SEPARATE COAT.
<br />3.4 PROTECTION
<br />PROTECT WORK OF OTHER TRADES AND ITEMS NOT INTENDED TO RECEIVE
<br />PAINT. INSTALL "WET PAINT" SIGNS TO PROTECT NEWLY PAINTED
<br />SURFACES.
<br />3.5 CLEANING
<br />PROTECTION - CAREFULLY PROTECT AREAS WHERE WORK IS IN PROGRESS
<br />FROM DAMAGE.
<br />PROVIDE AND SPREAD CLEAN DROP CLOTHS WHEN AND WHERE
<br />REQUIRED TO PROVIDE THE NECESSARY PROTECTION.
<br />IMMEDIATELY CLEAN-UP ALL ACCIDENTAL SPATTER, SPILLAGE,
<br />MISPLACED PAINT AND RESTORE THE AFFECTED SURFACE TO ITS
<br />ORIGINAL CONDITION.
<br />CLEAN-UP:
<br />CLEAN UP DEBRIS DAILY PER OSHA REQUIREMENTS.
<br />AT COMPLETION OF WORK, REMOVE ALL MATERIALS, SUPPLIES, DEBRIS
<br />AND RUBBISH AND LEAVE EACH AREA IN A CLEAN, ACCEPTABLE
<br />CONDITION.
<br />COLLECT WASTE MATERIAL WHICH MAY CONSTITUTE A FIRE HAZARD,
<br />PLACE IN CLOSED METAL CONTAINERS, AND REMOVE DAILY FROM SITE.
<br />3.6 SURFACES TO BE FINISHED
<br />PAINT ALL NEW WORK AND AREAS AFFECTED BY NEW WORK, UNLESS
<br />NOTED OTHERWISE.
<br />DO NOT PAINT OR FINISH THE FOLLOWING ITEMS:
<br />ITEMS FULLY FACTORY-FINISHED UNLESS SPECIFICALLY NOTED.
<br />FIRE RATING LABELS, EQUIPMENT SERIAL NUMBER AND CAPACITY
<br />LABELS.
<br />MECHANICAL AND ELECTRICAL: USE PAINT SYSTEMS DEFINED FOR THE
<br />SUBSTRATES TO BE FINISHED.
<br />PAINT ALL INSULATED AND EXPOSED PIPES OCCURRING IN FINISHED
<br />AREAS TO MATCH BACKGROUND SURFACES, UNLESS OTHERWISE
<br />INDICATED.
<br />PAINT SHOP PRIMED ITEMS OCCURRING IN FINISHED AREAS.
<br />PAINT INTERIOR SURFACES OF AIR DUCTS AND CONVECTOR AND
<br />BASEBOARD HEATING CABINETS THAT ARE VISIBLE THROUGH GRILLES
<br />AND LOUVERS WITH ONE COAT OF FLAT BLACK PAINT.
<br />PAINT DAMPERS EXPOSED BEHIND LOUVERS, GRILLES AND CONVECTOR
<br />AND BASEBOARD CABINETS TO MATCH FACE PANELS.
<br />3.7 PAINT SYSTEMS - EXTERIOR
<br />PLASTER/STUCCO, OPAQUE, EGGSHELL, LATEX, 3 COAT:
<br />ONE COAT: LOXON MASONRY PRIMER A24W300.
<br />TWO COATS (UPGRADE): S-W SUPER PAINT EXTERIOR LATEX (1.4 MILS
<br />DFT PR/CT).
<br />FERROUS METALS, UNPRIMED, LATEX, 3 COAT:
<br />ONE COAT: PRO-CRYL PRIMER UNIVERSAL PRIMER
<br />TWO COATS: PRO INDUSTRIAL WATER BASED ALKYD
<br />GALVANIZED METALS, SEMI-GLOSS, ALKYD, 3 COAT:
<br />ONE COAT: PRO-CRYL UNIVERSAL PRIMER B66-310.
<br />TWO COATS: PRO INDUSTRIAL WATER BASED ALKYD.
<br />WOOD AND COMPOSITE WOOD, FLAT, OPAQUE, LATEX, 3 COAT:
<br />ONW COAT: A-100 EXTERIOR LATEX PRIMER B42W41
<br />TWO COATS: A-100 FLAT A6W851.
<br />WOOD AND COMPOSITE WOOD, SEMI-GLOSS, OPAQUE, LATEX, 3 COAT
<br />ONE COAT: A-100 EXTERIOR LATEX PRIMER B42W41.
<br />TWO COATS: SOLO 100% ACRYLIC A76 SERIES.
<br />3.8 PAINT SYSTEMS -INTERIOR (NO VOC)
<br />GYPSUM BOARD, LATEX EGG-SHELL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX EG-SHELL, B9 SERIES.
<br />GYPSUM BOARD, ACRYLIC SEMI-GLOSS ENAMEL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX SEMI-GLOSS B10 SERIES.
<br />MASONRY, LATEX EGG-SHELL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX EGG-SHELL, B9 SERIES.
<br />PLASTER, LATEX EGG-SHELL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX EG-SHELL, B9 SERIES.
<br />PLASTER, ACRYLIC SEMI-GLOSS ENAMEL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX SEMI-GLOSS B10 SERIES.
<br />WOOD, COMPOSITION BOARD, LATEX EGG-SHELL:
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: HARMONY INTERIOR LATEX EG-SHELL, B9 SERIES.
<br />WOOD, ACRYLIC SEMI-GLOSS ENAMEL
<br />ONE COAT: HARMONY INTERIOR LATEX PRIMER B11W900.
<br />TWO COATS: SOLO 100% ACRYLIC SEMI-GLOSS A76 SERIES.
<br />METAL - STEEL, ALUMINUM, GALVANIZED, ACRYLIC SEMI-GLOSS ENAMEL:
<br />ONE COAT: ONE COAT: PRO-CRYL UNIVERSAL PRIMER B66-310.
<br />TWO COATS: PRO INDUSTRIAL WATER BASED ALKYD.
<br />3.9 COLORS
<br />TO BE SELECTED BY ARCHITECT FROM DISTRICT ’S STANDARD COLOR
<br />PALETTE.
<br />09 PAINT (CONT.)DEMOLITION
<br />CEILINGS
<br />No. C31793W
<br />REN. 02-28-25
<br />L
<br />AINROFILACFOETATS
<br />ICENSED A RCHITECT
<br />N
<br />I
<br />LL M I TZE
<br />I A
<br />Job. No.
<br />Date
<br />Drawn/Checked by
<br />Scale
<br />FOR PLAN
<br />REVIEW ONLY
<br />This and all other project documents and all ideas, aesthetics and
<br />designs incorporated therein are instruments of service.
<br />All project documents are the registered property of ITZEN. (ITZEN)
<br />and cannot be lawfully used in whole or in part for any project or
<br />purpose except as described in the contractual agreement between
<br />ITZEN and Client. ITZEN hereby gives formal notice that any such
<br />project document use, reproduction or modification (misuse) is not only
<br />unlawful but automatically binds all parties involved with misuse to fully
<br />indemnify and defend ITZEN and ITZEN's Consultants to the maximum
<br />legal extent against all losses, demands, claims or liabilities arising
<br />directly or indirectly from project document misuse.
<br />Project documents describe design intent of work and are not a
<br />representation of as-built or existing conditions. ITZEN and ITZEN's
<br />Consultants make no representations concerning the accuracy of
<br />documents and are not responsible for any discrepancies between
<br />project documents and the existing conditions.
<br />Copyright 2021C
<br />mailing:
<br />1800 N. Bristol Street #C-418
<br />Santa Ana CA 92706
<br />714-716-5042
<br />sayhello@ITZEN.com
<br />www.ITZEN.com
<br /> 12" = 1'-0"
<br />23014
<br />04-08-2024
<br />WBI/AT
<br />AS
<br />S
<br />I
<br />S
<br />T
<br />A
<br />N
<br />C
<br />E
<br />
<br />L
<br />E
<br />A
<br />G
<br />U
<br />E
<br />
<br />O
<br />F
<br />
<br />S
<br />A
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />10
<br />3
<br />1
<br />
<br />W
<br />
<br />F
<br />I
<br />R
<br />S
<br />T
<br />
<br />S
<br />T
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />3
<br />ME
<br />C
<br />H
<br />A
<br />N
<br />I
<br />C
<br />A
<br />L
<br />
<br />E
<br />Q
<br />U
<br />I
<br />P
<br />M
<br />E
<br />N
<br />T
<br />
<br />S
<br />C
<br />R
<br />E
<br />E
<br />N
<br />SHEET
<br />SPECIFICATIONS
<br />A0.1
<br />REV DESCRIPTION DATE
<br />1031 W 1st St -
<br />101119950 & 4013927010/18/2024
|