|
AT
<br />T
<br />I
<br />C
<br />HP
<br />W/H
<br />RE
<br />F
<br />.
<br />DW
<br />DW
<br />AT
<br />T
<br />I
<br />C HP
<br />1. VERIFY ALL APPLIANCE EQUIPMENT AND FIXTURE DIMENSIONS AND INSTALLATION REQUIREMENTS PRIOR TO CASEWORK FABRICATION
<br />INSTALLATION.
<br />2. FINISH END WALLS OF CABINETS FLANKING OPENING TO MATCH CABINET FACE. PRIME & PAINT EXPOSED GYP. BD. WALL TO MATCH WALLS.
<br />INSTALL MATCHING BASE BD.
<br />3. EXTEND FLOORING UNDER APPLIANCES RESTING ON FLOOR.
<br />4. SHOWER COMPARTMENTS AND WALLS ABOVE BATH TUBS WITH INSTALLED SHOWER HEADS SHALL BE FINISHED WITH A SMOOTH, NON-
<br />ABSORBENT SURFACE TO A HEIGHT NOT LESS THAN 72 INCHES ABOVE THE DRAIN INLET.
<br />5. OFFSET ALL IMMEDIATELY ADJACENT DOOR OPENINGS 4" FROM PERPENDICULAR WALL, UNO.
<br />6. CEILING HEIGHTS INDICATED ARE MEASURED FROM FINISH FLOOR TO BOTTOM OF CEILING FINISH.
<br />7. SMOKE DETECTORS WILL BE PROVIDED PER CHAPTER 3 CRC. THE SMOKE DETECTOR WILL BE HARD WIRED WITH BATTERY BACK-UP AND
<br />LOCATED (1) IN EACH BEDROOM, HALLWAYS OUTSIDE BEDROOMS, AND ON EACH STORY. SMOKE DETECTOR ALARM SOUND MUST BE AUDIBLE
<br />IN SLEEPING AREAS WHICH MAY REQUIRE INTERCONNECTED SMOKE DETECTORS WITHIN THE UNIT. SEE UTILITY PLANS FOR LOCATIONS.
<br />INSTALL AND LOCATE PER MFGR. LISTED REQUIREMENTS.
<br />8. PROVIDE CARBON MONOXIDE DETECTOR ALARMS ON CEILINGS OR WALLS OUTSIDE SLEEPING ROOMS PER CHAPTER 3 CRC.
<br />9. BATHROOM FANS MUST BE ENERGY STAR W/ HUMIDISTAT CONTROLLER AND MUST BE DUCTED TO THE EXTERIOR OF THE BUILDING
<br />10. ALL NEW WINDOWS TO BE DUAL PANES TO MEET CURRENT ENERGY STANDARD REQUIREMENTS.
<br />11. PROVIDE BACKING FOR ALL ACCESSORIES, FIXTURES AND WINDOW COVERINGS.
<br />12. PROVIDE TWO LAYERS OF GRADE D OR 60-MINUTE GRADE D PAPER OVER ALL WOOD BASE SHEATHING AT EXTERIOR WALLS.
<br />13. A MINIMUM 26 GAUGE, CORROSION RESISTANT OR PLASTIC WEEP SCREED WITH A MINIMUM VERTICAL FLANGE OF 3½ INCHES SHALL BE
<br />PROVIDED AT OR BELOW FOUNDATION PLATE LINE ON EXTERIOR STUD WALLS. SCREED SHALL BE A MINIMUM OF 4 INCHES ABOVE EARTH OR
<br />2 INCHES ABOVE PAVED AREAS. (CRC R703.7.2.1)
<br />14. ACCESS TO ATTIC FURNACE MUST BE WITHIN 20' OF UNIT AND SHALL HAVE A CONTINUOUS SOLID WALKWAY AT LEAST 24" WIDE. A SWITCH
<br />CONTROL IS ALSO REQUIRED (CMC 304.4.1)
<br />15. DOMESTIC DRYER MOISTURE EXHAUST DUCTS SHALL NOT EXCEED A TOTAL COMBINED HORIZONTAL AND VERTICAL LENGTH OF 14 FEET
<br />(4267 MM), INCLUDING TWO 90 DEGREE (1.57 RAD) ELBOWS. A LENGTH OF 2 FEET (610 MM) SHALL BE DEDUCTED FOR EACH 90 DEGREE (1.57
<br />RAD) ELBOW IN EXCESS OF TWO.
<br />16. PROVIDE LOW CONSUMPTION WATER CLOSETS FOR ALL NEW CONSTRUCTION. EXISTING SHOWER HEADS AND TOILETS MUST BE ADAPTED
<br />FOR LOW WATER CONSUMPTION.
<br />17. WATER HEATER MUST BE STRAPPED TO WALL.
<br />18. EVERY SPACE INTENDED FOR HUMAN OCCUPANCY SHALL BE PROVIDED WITH A NATURAL LIGHT IN ACCORDANCE WITH SECTION R303.1 OR
<br />SHALL BE PROVIDE AN AVERAGE ILLUMINATION OF 6 FEET-CANDLES OVER THE AREA OF THE ROOM AT A HEIGHT OF 30" ABOVE THE FLOOR
<br />LEVEL.
<br />19. GLAZING WHICH IS LESS THAN 60 INCHES FROM A FLOOR AND WITHIN A 24" ARC OF A DOORWAY'S VERTICAL EDGE MUST COMPLY WITH CH.3
<br />CRC
<br />20. LANDINGS AT DOOR. LANDINGS SHALL HAVE A WIDTH NOT LESS THAN THE WIDTH OF THE STAIRWAY OR THE DOOR, WHICHEVER IS GREATER.
<br />21. ALL WATER HEATER INSTALLATION LOCATIONS, REGARDLESS OF PROPOSED WATER HEATING SYSTEM, SHALL HAVE:
<br />(BEES 150.0(N)1A-D)
<br />A. A 120V ELECTRICAL RECEPTACLE THAT IS WITHIN 3 FEET FROM THE WATER HEATER.
<br />B. A CATEGORY III OR IV VENT, OR A TYPE B VENT WITH STRAIGHT PIPE.
<br />C. CONDENSATE DRAIN THAT IS NO MORE THAN 2 INCHES HIGHER THAN THE FINISH SURFACE BELOW.
<br /> D. A GAS SUPPLY LINE WITH AVAILABLE CAPACITY FOR NOT LESS THAN A 200,000 BTU/HR SYSTEM.
<br />22. ADU FINISH FLOOR ELEVATION IS NOT NOT LOWER THAN THE FINISH FLOOR OF THE MAIN HOUSE AND HIGHER 1' MINIMUM THAN BASE FLOOD
<br />ELEVATION.
<br />EXHAUST FAN ABOVE KITCHEN RANGE SHALL BE 85%
<br />CE OR 250 CFM (EXHAUST THROUGH ROOF)
<br />(N) 2X4 INTERIOR WALL
<br />(N) 2X4 EXTERIOR WALL / INFILL
<br />WITH INSULATION PER T-24
<br />1-HOUR FIRE RATED WALL
<br />EXHAUST FAN SHALL BE ENERGY STAR RATED. CEILING
<br />MOUNTED LIGHT w/ VENT 50 CFM MIN. INTERMITTENT W/
<br />HUMIDITY CONTROL PER CMC 402.5, BETWEEN 50%-80%
<br />SHALL BE DUCTED TO OUTSIDE THROUGH ROOF/EXTERIOR WALL
<br />IAQ FAN: ( MIN 46 CFM PER T-24 )
<br />PANASONIC, WHISPERGREE, SELECT FAN, 50-80-110 SFM,
<br />MULTI SPEED. MODEL FV-0511VKS2, 0.5 SONE
<br />HB
<br />3/4" HOSE BIBB WITH BACK-FLOW PREVENTOR
<br />SMOKE DETECTOR HARDWIRED w/ BATTERY BACK UPSD
<br />CARBON MONOXIDE DETECTOR ALARM
<br />HARDWIRED w/ BATTERY BACK UP
<br />CD
<br />22X30 ATTIC ACCESS
<br />HEATPUMP + AIR HANDLER
<br />HEATPUMP UNIT ON PAD 3" MIN.
<br />LAUNDRY DRYER EXHAUST
<br />CEILING AIR DIFFUSER
<br />ELECTRICAL PANEL/METER PER KEYNOTE
<br />CONSUMER TANK WITH/ HEAT PUMP
<br />DOOR TYPE SEE A.08 FOR SCHEDULE
<br />WINDOW TYPE SEE A.08 FOR SCHEDULE
<br />KEY NOTE
<br />FLOOR DEPRESSION1.5''
<br />XX
<br />XX
<br />XX
<br />WHOLE HOUSE FAN: 1186.5 CFM PER T-24
<br />E ELECTRICAL VEHICLE CHARGING
<br />STATION LOCATION. 208/240-VOLT
<br />BRANCH CIRCUIT (40 AMP)
<br />1
<br />1
<br />2
<br />3
<br />4
<br />5
<br />7
<br />9 EXHAUST FAN FOR BATHROOM SHALL BE MINIMUM 50 CFM
<br />AND CONTAIN HUMIDISTAT (EXHAUST THROUGH ROOF).
<br />10 EXHAUST FAN ABOVE KITCHEN GAS RANGE SHALL BE 85% CE OR 250
<br />CFM (EXHAUST THROUGH ROOF)
<br />11
<br />8
<br />(N) DUAL-GANG ELECT. METER BOX
<br />(N) ELECTRICAL SUB-PANEL 225 AMPS
<br />(N) LANDING. 1 1/2" BELOW THRESHOLD. MINIMUM 36" IN
<br />DEPTH.MIN. 2% SLOPE AWAY FROM BUILDING.
<br />(N) 22X30 ATTIC ACCESS
<br />2'' SHOWER CURB
<br />MIN. 4" DIA. TO THE OUTSIDE, EQUIPPED WITH A BACK
<br />DRAFT DAMPER. EXHAUST DUCT LENGTH IS LIMITED TO 14
<br />FT. WITH 2 ELBOWS. [CMC 504.4.2] (EXHAUST THROUGH
<br />EXTERIOR WALL/ROOF)
<br />6
<br />(N) HEAT PUMP UNIT ON 3" THIK. CONCRETE PAD
<br />(N) 6X6 POST
<br />TEMPERED GLASS
<br />12 (N) CONSUMER TANK WITH/ HEAT PUMP, DETAIL ON SHEET A.03
<br />13 APPROVED PRE-FABRICATED SHOWER ENCLOSURES WALL PANELS
<br />WITH FACTORY-INSTALLED REINFORCEMENT FOR GRAB BARS. SMOOTH,
<br />NON-ABSORBENT SURFACE TO A HEIGHT NOT LESS THAN 72 INCHES
<br />ABOVE THE DRAIN INLET
<br />14 FUTURE INSTALLED FLOOR MOUNTED FOLDABLE GRAB BAR
<br />15 2X8 BACKING FOR FUTURE GRAB BAR INSTALLATION
<br />16 32'' MIN. CLR. INTERIOR DOOR SEE NOTE ON ''AGING-IN-PLACE''
<br />17
<br />18 OBSCURED,TEMPERED GLASS
<br />19 1HR FIRE RATED WALL, UPNPROTECTED OPENING MAX
<br />25% WALL AREA, SEE CALCULATION ON ELEV. 01/A.06,02/A.06
<br />20 8'' GARAGE CURB, SEE STRUCTURAL DWG
<br />21 DOOR BETWEEN GARAGE AND LIVING AREA SHALL BE 20 MIN. RATED 1-3/8"
<br />SOLID CORE WITH CLOSER AND LATCHING HARDWARE, SMOKE SEAL @
<br />JAMB, HEAD @ METAL THRESHOLD
<br />5/8" TYPE "X" GYPSUM BOARD ALL WALLS, CEILINGS, BEAMS, POSTS
<br />AND COLUMNS, SMOOTH FINISH TYPICAL AT GARAGE
<br />1.ENCLOSED ATTICS AND ENCLOSED RAFTER SPACES FORMED WHERE CEILINGS ARE APPLIED DIRECTLY TO THE
<br />UNDERSIDE OF ROOF RAFTERS SHALL HAVE CROSS VENTILATION FOR EACH SEPARATE SPACE BY VENTILATING
<br />OPENINGS PROTECTED AGAINST THE ENTRANCE OF RAIN OR SNOW. VENTILATION OPENINGS SHALL HAVE AT LEAST
<br />DIM. OF 1/16" MIN. AND 1/4" MAX. VENTILATION OPENINGS HAVING A LEAST DIMENSION LARGER THAN 1/4" SHALL BE
<br />PROVIDED W/. CORROSION-RESISTANT WIRE CLOTH SCREENING, HARDWARE CLOTH, OR SIMILAR MATERIAL WITH
<br />OPENINGS HAVING A LEAST DIM. OF 1/16" MIN. AND 1/4" MAX. OPENINGS IN ROOF FRAMING MEMBERS SHALL CONFORM
<br />TO THE REQ'TS. OF CRC R802.7. REQUIRED VENTILATION OPENINGS SHALL OPEN DIRECTLY TO THE OUTSIDE AIR.
<br />2. THE NET FREE VENTILATING AREA SHALL NOT BE LESS THAN 1/150 OF THE AREA OF THE SPACE VENTILATED. THE
<br />NET FREE VENTILATING AREA SHALL NOT BE LESS THAN 1/300 IF ONE OR MORE OF THE FOLLOWING ARE MET; 1. IN
<br />CLIMATE ZONES 14 & 16, A CLASS I OR II VAPOR RETARDER IS INSTALLED ON THE WARM-IN-WINTER SIDE OF THE
<br />CEILING. 2. AT LEAST 40% AND MORE THAN 50% OF THE REQUIRED VENTILATING ARE IS PROVIDED BY VENTILATORS
<br />LOCATED IN THE UPPER PORTION OF THE ATTIC OR RAFTER SPACE. UPPER VENTILATORS SHALL BE LOCATED NO MORE
<br />THAN 3 FEET BELOW THE RIDGE OR HIGHEST POINT OF THE SPACE, MEASURED VERTICALLY, WITH THE BALANCE OF
<br />TEH REQUIRED VANTILATION PROVIDED BY EAVE OR CORNICE VENTS. WHERE THE LOCATION OF WALL OR ROOF
<br />FRAMING MEMBERS CONFLICTS WITH THE INSTALLATION OF UPPER VENTILATORS, INSTALLATION MORE THAN 3 FEET
<br />BELOW THE RIDGE OR HIGHEST OF THE SPACE SHALL BE PERMITTED.
<br />3. WHERE EAVE OR CORNICE VENTS ARE INSTALLED, INSULATION SHALL NOT BLOCK THE FREE FLOW OF AIR. A MIN. OF
<br />A 1" SPACE SHALL BE PROVIDED BETWEEN THE INSULATION AND THE ROOF SHT'G. AND AT THE LOCATION OF THE VENT.
<br />4. VENTILATORS SHALL BE INSTALLED IN ACCORDANCE WITH MFR'G.'S INSTALLATION INSTRUCTIONS. INSTALLATION OF
<br />VENTILATORS IN ROOF SYSTEMS SHALL BE IN ACCORDANCE W/. THE REQ'TS. OF SECTION R903. INSTALLATION OF
<br />VENTILATORS IN WALL SYSTEMS SHALL BE IN ACCORDANCE W/. THE REQ'TS. OF SECTION R703.1.
<br />5. UNVENTED ATTIC ASSEMBLIES (SPACES BETWEEN THE CEILING JOISTS OF THE TOP STORY AND THE ROOF RAFTERS)
<br />AND UNVENTED ENCLOSED RAFTER ASSEMBLIES (SPACES BETWEEN CEILINGS THAT ARE APPLIED DIRECTLY TO THE
<br />UNDERSIDE OF ROOF FRAMING MEMBER/RAFTERS AND THE STRUCTURAL ROOF SHT'G. AT THE TOP OF THE ROOF
<br />FRAMING MEMBERS/RAFTERS) SHALL BE PERMITTED IF ALL OF THE FOLLOWING CONDITIONS ARE MET:
<br />1. THE UNVENTED ATTIC SPACE IS COMPLETELY CONTAINED WITHIN THE BUILDING THERMAL ENVELOPE.
<br />2. NO INTERIOR CLASS I VAPOR RETARDERS ARE INSTALLED ON THE CEILING SIDE (ATTIC FLOOR) OF THE
<br />UNVENTED ATTIC ASSEMBLY OR ON THE CEILING SIDE OF THE UNVENTED ENCLOSED RAFTER ASEEMBLY.
<br />3. WHERE WOOD SHINGLES OF SHAKES ARE USED, A MIN. 1/4" VENTED AIR SPACE SEPARATES THE SHINGLES OR
<br />SHAKES AND THE ROOFING UNDERLAYMENT ABOVE THE STRUCTURAL SHT'G.
<br />4. IN CALIFORNIA CLIMATE ZONES 14 & 16, ANY AIR-IMPERMEABLE INSULATION SHALL BE A CLASS II VAPOR
<br />RETARDER, OR SHALL HAVE A CLASS III VAPOR RETARDER COATING OR COVERING IN DIRECT CONTACT W/. THE
<br />UNDERSIDE OF THE INSULATION (SEE TITLE 24, PART 6, FIG. 100.1-A)
<br />5. EITHER ITEMS 5.1, 5.2 OR 5.3 SHALL BE MET, DEPENDING ON THE AIR PERMEABILITY OF THE INSULATION
<br />DIRECTLY UNDER THE STRUCTURAL ROOF SHT'G. (NO INSULATION SHALL BE REQ'D. WHEN ROOF TILES, WOOD
<br />SHINGLES OR WOOD SHAKES, OR ANY OTHER ROOFING SYSTEM USING BATTENS AND NO CONT. UNDERLAYMENT IS
<br />INSTALLED. A CONT. LAYER SHALL BE CONSIDERED TO EXIST IF SHT'G., ROOFING PAPER OR ANY CONT. LAYER
<br />WHICH HAS A PERM RATE OF NO MORE THAN ONE PERM UNDER THE DRY CUP METHOD.);
<br />5.1. AIR-IMPERMEABLE INSULATION ONLY. INSULATION SHALL BE APPLIED IN DIRECT CONTACT W/. THE
<br />UNDERSIDE OF THE STRUCTURAL ROOF SHT'G.
<br />5.2. AIR-PERMEABLE INSULATION ONLY. IN ADDITION TO THE AIR-PERMEABLE INSULATION INSTALLED DIRECTLY
<br />BELOW THE STRUCTURAL SHT'G., RIDGE BOARD OR SHEET INSULATION W/. AN R-VALUE OR R-4 SHALL BE
<br />INSTALLED DIRECTLY ABOVE THE STRUCTURAL ROOF SHT'G. FOR CONDENSATION CONTROL.
<br />5.3. AIR-IMPERMEABLE AND AIR-PERMEABLE INSULATION. THE AIR-IMPERMEABLE INSULATION SHALL BE
<br />APPLIED IN DIRECT CONTACT W/. THE UNDERSIDE OF THE STRUCTURAL ROOF SHT'G. FOR CONDENSATION
<br />CONTROL. THE AIR-PERMEABLE INSULATION SHALL BE INSTALLED DIRECTLY UNDER TH AIR-PERMEABLE
<br />INSULATION.
<br />5.4. WHERE PREFORMED INSULATION BOARD IS USED AS THE AIR0IMPERMEABLE INSULATION LAYER, IT SHALL
<br />BE SEALED AT THE PERIMETER OF EACH INDIVIDUAL SHEET INTERIOR SURFACE TO FORM A CONT. LAYER.
<br />ATTIC AREA: 800 SF
<br />USE BALANCE METHOD : 1/300
<br />NET VENT AREA REQUIRE : 800/300 x 144 SQ.IN. = 384 SQ.IN
<br />FOR WHOLE HOUSE VENT: 1186.5 CFM-227 SQ.IN VENT NFA IS REQUIRED ( 144 SQFT PER 750
<br />CFM)
<br />TOTAL VENT AREA REQUIRED: 611 SQ.IN
<br />NOTE: MAX 50% ON UPPER ROOF AREA
<br />LOW: USE 3 UNITS O'HAGIN VENT (72 SQ.IN/UNIT) = 216 SQ.IN (1/3 LOW AREA OF ROOF)
<br />HIGHT: USE 3 UNITS O'HAGIN VENT (72 SQ.IN/UNIT)= 216 SQ.IN (1/3 HEIGHT AREA OF ROOF)
<br />+ 10 FT RIGDE VENT (18 SQ.IN/FOOT)= 180 SQ.IN
<br />TOTAL = 612 SQ.IN
<br />4'-9 1/2"4'-9 1/2"
<br />9'-7 1/2"
<br />2'
<br />-
<br />0
<br />"
<br />3'-1"
<br />11
<br />'
<br />-
<br />4
<br />
<br />1
<br />/
<br />2
<br />"
<br />2'
<br />-
<br />4
<br />
<br />1
<br />/
<br />2
<br />"
<br />3'
<br />-
<br />8
<br />"
<br />3'
<br />-
<br />5
<br />"
<br />20
<br />'
<br />-
<br />1
<br />0
<br />"
<br />15'-1 1/2"8'-10"5'-4 1/2"
<br />5'
<br />-
<br />7
<br />
<br />1
<br />/
<br />2
<br />"
<br />4'
<br />-
<br />7
<br />"
<br />3'-10"8'-4"5'-4 1/2"
<br />B
<br />A.06
<br />B
<br />A.06
<br />GARAGE
<br />15"15"
<br />17
<br />"
<br />17
<br />"
<br />21'-1 1/2"12'-8"
<br />5'
<br />-
<br />8
<br />"
<br />17
<br />'
<br />-
<br />1
<br />1
<br />"
<br />8'-0"
<br />5'
<br />-
<br />0
<br />"
<br />5'-0"
<br />14
<br />'
<br />-
<br />9
<br />"
<br />51'-4"
<br />A.06
<br />2
<br />A.
<br />0
<br />6
<br />3
<br />A.06
<br />1
<br />A.
<br />0
<br />6
<br />4 8'
<br />-
<br />8
<br />
<br />1
<br />/
<br />2
<br />"
<br />11'-9 1/2"
<br />3'
<br />-
<br />6
<br />"
<br />5'
<br />-
<br />3
<br />"
<br />11
<br />'
<br />-
<br />0
<br />"
<br />8'-11 1/2"
<br />5'-0"
<br />A
<br />A.06
<br />A
<br />A.06
<br />SD
<br />CDSD
<br />CDSD
<br />SD
<br />30"
<br />3'-0"
<br />6'
<br />-
<br />0
<br />"
<br />1.
<br />5
<br />'
<br />'
<br />1.5''
<br />1 2
<br />3
<br />5
<br />3
<br />3
<br />3
<br />4
<br />6
<br />5'
<br />-
<br />0
<br />"
<br />20'-9"
<br />14
<br />'
<br />-
<br />1
<br />"
<br />A
<br />B
<br />B C
<br />30'' CLR
<br />30'' CLR 12
<br />6
<br />11
<br />3
<br />3 11
<br />16
<br />9
<br />9
<br />7
<br />10
<br />13
<br />13
<br />11 5
<br />5
<br />15
<br />3'-5 1/2"
<br />36'' CLR.
<br />FRONT OF
<br />PANEL
<br />15 14
<br />14
<br />BEDROOM#1
<br />10FT CL'G
<br />KITCHEN
<br />10FT CL'G
<br />LIVING
<br />10FT CL'G
<br />BEDROOM#2
<br />10FT CL'G
<br />W.I.C
<br />10FT CL'G
<br />BATH#1
<br />10FT CL'G
<br />BATH#2
<br />10FT CL'G
<br />PORCH
<br />CLOSET
<br />4'
<br />-
<br />6
<br />
<br />1
<br />/
<br />2
<br />"
<br />EE&RO
<br />EE&RO
<br />18
<br />18
<br />19
<br />19
<br />2
<br />AD.20
<br />2
<br />AD.20
<br />88
<br />21
<br />NOTE: NO INSULATION
<br />NO HEATING
<br />NO COOLING
<br />20
<br />17
<br />2
<br />AD.20
<br />6
<br />AD.20
<br />2''
<br />4
<br />11
<br />2020
<br />10FT CL'G
<br />19
<br />COVER PORCH
<br />12'-0"
<br />6'-4"6'-0"
<br />7
<br />1
<br />1
<br />1
<br />1
<br />21
<br />'
<br />-
<br />5
<br />"
<br />EELECTRICAL VEHICLE
<br />CHARGING STATION
<br />LOCATION. 208/240-VOLT
<br />BRANCH CIRCUIT (40 AMP)
<br />1
<br />B
<br />A.06
<br />B
<br />A.06
<br />1'-0"1'-0"
<br />6'
<br />-
<br />2
<br />"
<br />1'
<br />-
<br />0
<br />"
<br />1'-0"
<br />WA
<br />L
<br />L
<br />
<br />L
<br />I
<br />N
<br />E
<br />
<br />
<br />B
<br />E
<br />L
<br />O
<br />W
<br />
<br />WALL LINE BELOW
<br />WALL LINE BELOW
<br />WA
<br />L
<br />L
<br />
<br />L
<br />I
<br />N
<br />E
<br />
<br />B
<br />E
<br />L
<br />O
<br />W
<br />
<br />WA
<br />L
<br />L
<br />
<br />L
<br />I
<br />N
<br />E
<br />
<br />B
<br />E
<br />L
<br />O
<br />W
<br />
<br />WALL LINE BELOW
<br />WALL LINE BELOW
<br />WA
<br />L
<br />L
<br />
<br />L
<br />I
<br />N
<br />E
<br />
<br />B
<br />E
<br />L
<br />O
<br />W
<br />
<br />A.06
<br />2
<br />A.
<br />0
<br />6
<br />3
<br />A.06
<br />1
<br />A.
<br />0
<br />6
<br />4
<br />ROOF MATERIAL COVERING CLASS "A", TO MATCH WITH
<br />EXISTING ROOF (EXISTING ROOFING MATERIAL TYPE:
<br />ASPHALT SHINGLES BY CERTAINTEED ICC-ESR# 3537).
<br />OVER PLYWOOD SHEATING OVER RADIANT BARRIER
<br />OVER RAFTERS PWE STRUCTURAL DWGS.
<br />3'-0"
<br />4:12
<br />4:
<br />1
<br />2
<br />4:
<br />1
<br />2
<br />A
<br />A.06
<br />A
<br />A.06
<br />O'HAGIN VENT 72 SQ.IN TYP.
<br />O'HAGIN VENT 72 SQ.IN TYP.
<br />3FT MIN.
<br />3'
<br />-
<br />4
<br />"
<br />3FT MIN.
<br />3'-0"
<br />O'HAGIN VENT 72 SQ.IN TYP.
<br />FUTURE SOLAR ZONE
<br />100 SF
<br />FUTURE SOLAR ZONE
<br />160 SF
<br />POST BELOW POST BELOW
<br />2
<br />AD.20
<br />2
<br />AD.20
<br />2
<br />AD.20
<br />1'
<br />-
<br />0
<br />"
<br />1'-0"
<br />1'
<br />-
<br />0
<br />"
<br />1'-0"
<br />1'
<br />-
<br />0
<br />"
<br />1'
<br />-
<br />0
<br />"
<br />11"
<br />RIDGE VENT
<br />10'-0"
<br />EQEQEQ
<br />EQ EQ EQ
<br />IT IS THE SUBCONTRACTORS RESPONSIBILITY PRIOR TO OR DURING CONSTRUCTION TO
<br />NOTIFY THE DESIGNERS OR JOB FOREMAN IN WRITING OR IN VERBAL OF ANY
<br />PERCEIVED ERRORS OR OMISSIONS IN THE PLANS AND SPECIFICATIONS OF WHICH A
<br />SUBCONTRACTOR THOROUGHLY KNOWLEDGEABLE WITH THE BUILDING CODES AND
<br />METHODS OF CONSTRUCTION SHOULD REASONABLY BE AWARE. WRITTEN OR VERBAL
<br />INSTRUCTIONS ADDRESSING SUCH PERCEIVED ERRORS OR OMISSIONS SHALL BE
<br />RECEIVED FROM THE DESIGNERS OR JOB FOREMAN PRIOR TO THE SUBCONTRACTORS
<br />BEFORE PROCEEDING WITH THE WORK. THE OWNERS WILL NOT BE RESPONSIBLE FOR
<br />ANY DEFECTS IN CONSTRUCTION IF THESE PROCEDURES ARE NOT BEING FOLLOWED.
<br />DESCRIPTIONDATEDELTA
<br />NEW DETACHED ADU 2
<br />BEDS, 2BATHS,
<br />LIVING , KITCHEN,
<br />DINING , GARAGE-1
<br />CAR
<br />PROJECT CONTACT
<br />OWNERSHIP
<br />KHANH DAO
<br />10448 SALINAS RIVER CIR
<br />FOUNTAIN VALLEY, CA 92708
<br />PHONE: (714) 390-5154
<br />28/11/2023 PLANNING CORRECTIONS
<br />LOAN PHAM
<br />17021 BOLERO LN
<br />HUNTINGTON BEACH, CA 92649
<br />PHONE: 714-614-6344
<br />EMAIL:
<br />LOANPHAM8888@YAHOO.COM
<br />1 02/22/2024 1ST PLAN CHECK
<br />A.05
<br />PROPOSED ADU
<br />FLOOR & ROOF
<br />PLAN
<br />(N
<br />)
<br />
<br />D
<br />E
<br />T
<br />A
<br />C
<br />H
<br />E
<br />D
<br />
<br />A
<br />D
<br />U
<br />,
<br />
<br />U
<br />N
<br />I
<br />T
<br />
<br />2
<br />90
<br />1
<br />
<br />E
<br />
<br />M
<br />Y
<br />R
<br />T
<br />L
<br />E
<br />
<br />S
<br />T
<br />,
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />1
<br />(E
<br />)
<br />
<br />S
<br />I
<br />N
<br />G
<br />L
<br />E
<br />
<br />F
<br />A
<br />M
<br />I
<br />L
<br />Y
<br />
<br />R
<br />E
<br />S
<br />I
<br />D
<br />E
<br />N
<br />C
<br />E
<br />90
<br />1
<br />
<br />E
<br />
<br />M
<br />Y
<br />R
<br />T
<br />L
<br />E
<br />
<br />S
<br />T
<br />,
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />1
<br />1/4" = 1'-0"1PROPOSED ADU FLOOR PLAN
<br />1/4" = 1'-0"2PROPOSED ADU ROOF PLAN
<br />ROOF VENTILATION
<br />NOTES: (CRC R806)PLAN KEYNOTES FLOOR PLAN NOTES
<br />PLAN LEDGEND
<br />ROOF VENTILATION
<br />CALCULATION
<br />ROOF PLAN
<br />GENERAL NOTES
<br />1. ROOF MATERIAL COVERING CLASS "A" ASPHALT SHINGLES BY
<br />CERTAINTEED ICC-ESR# 3537. COLOR & PER THE INSTALLATION
<br />OF ROOF COVERING SHALL BE IN ACCORDANCE WITH
<br />MANUFACTURER'S SPECIFICATIONS.
<br />2. PROJECTIONS LESS THAN 5'-0" (HOUSE WITH NO SPRINKLER)
<br />TO PROPERTY LINE TO BE 1-HOUR CONSTRUCTION, TYP.
<br />3. ROOF VENT : SEE ROOF VENTILATION CALCULATION.
<br />901 E Myrtle St Unit# 2 -
<br />1011181606/27/2024
|