Laserfiche WebLink
All ideas, drawings,specifications shown herein are the <br />property of West Coast Design Group and shall not be <br />used, copied, reproduced, or disclosed to any person, firm <br />or corporation, without the written consent of West Coast <br />Design Group. Any infringement will be subject to legal <br />action. The contractor shall verify and be responsible for all <br />dimensions and conditions on the job and notify this office of <br />any variations from dimensions and conditions shown <br />herewith. Written dimensions take precedence over scaled <br />dimensions. <br />Mark Transmittal Set Date Description <br />01 <br />02 <br />12/19/2024 <br />3/14/2025 <br />Planning Corr. R1 <br />Building Corr. <br />SHEET TITLE <br />A-4 <br />SHEET 15 <br />PROJECT NO: <br />STATUS: <br />DRAWN BY: <br />CHK'D BY: <br /> <br /> <br />PROJECT: <br />CLIENT: <br />PLOT DATE: 3/14/2025 <br /> 52-24 <br />PLAN CHECK#:101122356 <br /> C <br />: <br />\ <br />U <br />s <br />e <br />r <br />s <br />\ <br />j <br />e <br />r <br />r <br />y <br />\ <br />D <br />o <br />c <br />u <br />m <br />e <br />n <br />t <br />s <br />\ <br />D <br />r <br />a <br />w <br />i <br />n <br />g <br />s <br />\ <br />R <br />e <br />s <br />i <br />d <br />e <br />n <br />t <br />i <br />a <br />l <br />\ <br />S <br />a <br />n <br />t <br />a <br /> <br />An <br />a <br /> <br />Gr <br />i <br />s <br />e <br />t <br /> <br />PI <br />\ <br />C <br />D <br />\ <br />S <br />a <br />n <br />t <br />a <br /> <br />A <br />n <br />a <br /> <br />G <br />r <br />i <br />s <br />e <br />t <br /> <br />P <br />I <br />. <br />p <br />l <br />n <br /> Submittal <br /> <br />Exterior Elevations <br />ADU <br />3110 & 3112 S Griset Pl <br />Santa Ana, CA 92704 <br />Matthew Mallari & <br />Natalie Nguyen <br />PLANNING - DESIGN <br />41055 CHACO CANYON ROAD <br />MURRIETA CA 92562 <br />WEST COAST <br />DESIGN GROUP <br />6 <br />A-6 <br />5 <br />A-7 <br />12 <br />' <br />- <br />3 <br />" <br />ASPHALT SHINGLE ROOF TO <br />MATCH MAIN RESIDENCE <br />GRADE <br />RIDGE <br />STUCCO FINISH TO MATCH <br />MAIN RESIDENCE <br />1 <br />A-6 <br />5 <br />A-7 <br />6 <br />A-6 <br />12 <br />' <br />- <br />3 <br />" <br />ASPHALT SHINGLE ROOF TO <br />MATCH EXISTING RESIDENCE <br />STUCCO FINISH TO MATCH <br />EXISTING RESIDENCE <br />GRADE <br />RIDGE <br />4X6 BEAM <br />2X6 BRACE <br />6 <br />A-6 <br />5 <br />A-7 <br />2 <br />A-612 <br />' <br />- <br />3 <br />" <br />ASPHALT SHINGLE ROOF TO <br />MATCH MAIN RESIDENCE <br />STUCCO FINISH TO MATCH <br />MAIN RESIDENCE <br />GRADE <br />RIDGE <br />TYP. <br />ATTIC VENT. SEE ROOF PLAN <br />NEW 150A ELECTRICAL <br />PANEL. SEE POWER PLAN <br />6 <br />A-6 <br />4 <br />A-7 <br />5 <br />A-7 <br />2 <br />A-612 <br />' <br />- <br />3 <br />" <br />ASPHALT SHINGLE ROOF TO <br />MATCH MAIN RESIDENCE <br />GRADE <br />RIDGE <br />STUCCO FINISH TO MATCH <br />MAIN RESIDENCE <br />TYP. <br />TEMP. <br />ATTIC VENT. SEE ROOF PLAN <br />NEW SPLIT AIR <br />CONDENSOR <br />4X6 BEAM SEE FRAMING <br />2X6 BRACE <br />2X6 RIDGE <br />BOARD <br />02 <br />02 <br />SCALE: 1/4" = 1'-0"1 North Elevation <br />SCALE: 1/4" = 1'-0"2 South Elevation <br />SCALE: 1/4" = 1'-0"3 East Elevation <br />SCALE: 1/4" = 1'-0"4 West Elevation <br />EXTERIOR ELEVATION NOTES <br />1. EXTERIOR PLASTER - 7/8" EXTERIOR PLASTER <br />APPLIED OVER A METAL LATH OVER (2) LAYERS OF <br />TYPE 'D' BUILDING PAPER. SPECIFY A MINIMUM <br />0.019" (NO.26 GALVANIZED SHEET GAGE) <br />CORROSION-RESISTANT OR PLASTIC WEEP SCREED <br />LOCATED BELOW FOUNDATION PLATE LINE AND 6 <br />INCHES ABOVE GRADE ON ALL EXTERIOR STUD WALL <br />OR 2-INCHES ABOVE PAVED AREAS. [CRC <br />R703.6.2.1.] ALSO NOTE 8" MIN. FINISH FLOOR TO <br />FINISH GRADE. <br />2. WEEP SCREEDS SHALL BE INSTALLED AT THE BASE <br />OF ALL EXTERIOR PLASTER WALLS. <br />3. ALL EXTERIOR OUTLETS SHALL BE WATER PROOF <br />WITH A COVER. SEE ELECTRICAL PLAN FOR MORE <br />INFO. <br />4. ALL WINDOWS AND DOORS SHALL BE INSTALLED <br />PER MANFACTURER'S DIRECTIONS. ALL EXTERIOR <br />DOORS AND WINDOWS SHALL BE SQUARED AND <br />FLASHED AS REQUIRED. <br />5. ALL EXPOSED METALS SHALL BE PAINTED TO MATCH <br />ADJACENT SURFACE. <br />6. STUCCO LATH AND DRYWALL SHALL BE NAILED TO <br />ALL STUDS AND TOP AND BOTTOM PLATE. <br />7. ROOFING SHALL MATCH EXISTING <br />8. ALL WINDOW TRIM TO MATCH MAIN RESIDENCE