10180319_3831 S. BRISTOL - Plan - Laserfiche WebLink

Home Browse Search

15 SIGN' COMPONENTS MANUAL (SAM)October 1,2013 2 These products are intended for use only when connected to a power source that €omplies with Class 2 voltage and energy limited circuitlimits and is rated 27 V DC or less. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage 0f greater than :the secondary or 00tput rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources. rated at 27 V DC or less· 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. ADHESIVE SYSTEMS INC 9411 CORSAIR RD E350958 FRANKFORT, IL 60423 Polymeric adhesive system, Cat. No. MP55420. 1. The ilse of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not exceeded. 2. These systems may be used for secutemeht to any combination of surfaces Listed in Table A, provided the use temperature is no higher than 71°C. 3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been performed on the adhesive by itself. The Engineer must consider the need to Investigate the part of other than the properties investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for Polymeric Materials - Use in Electrical Equipment Evaluations, UL 746C. 4. The suitability for use wheh exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been determined. 5. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to another surface or configuration shall be determined iii the particular end use application. 6. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The minimum temperature rating is -35°C (-31 'F). 7. The adhesive shall be applied in accordance with the manufacturers instruction. All surfaces shall be clean and dry. The manufacturer's instructions regarding cure time shall be followed. 8. The adhesive bond strength specified in Table A includes a safety factor of four. 9. When considering the use of any adhes,ve covered by this Report, the strength of the adhesive joint used to position parts shall be capable of withstanding the maximum force that might be applied to the joint ih the end application. This is called the bond strength and includes static load as well as wind loading(dynamic load). The minimum square ihches of adhesive to use is dete,mined by dividing the maximum load in pounds by the adhesive bond strength specified in Table A. ADVANCED LIGHTING CONCEPTS INC,E345129 DBA ENVIRONMENTALLIGHTS.COM SUITE 102 11235 W BERNARDO CT SAN DIEGO, CA 92127 Class 2 Power Supply, Models 4x60W12VDimX-120AC, 3x96W24VDimX-120AC. 1. These power supplies have been evaluated for use in LED signs. 2. The power supplies have outputs that individually comply with Class 2 circuit requirements. 3. These units are suitable for use in dry and damp locations without a need for an additional enclosure. 4. The output of this power source shall not be connected to any other power source or provide power to components connected to another power source. 5. These products shall have conductofs entering, leaving or residing in the wiring compartment or junction box extending af least 150 mm (6 in) inside. VAGILIGHT INC SUITE 108 1218 ARION PKY SAN ANTONIO, TX 78216 E255447 Class 2 LEDs, Cat. No. "SideWinder" may be followed by (Standard) or "SideWinder BL" Cat Nos. LS-A-BBB-GZ; where A (model or series name e.g. Side\Mnder) and SBB (color designation) may be replaced by alphanumeric characters; and Z may be replaced with alpha characters to denote generation number. 1.These products are only suitable for connection to a UL Listed or Recognized maximum Class 2,12 VAC or DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 icirouit limits. 3. These Class 2 LED modules, are each rated max. 40 Watts per unit, LED module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 sOpply. ' 4. These products are suitable for use in dry, damp or wet locations. 5. These products are not required to be enclosed or protected from the weather. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered. LED array drivers, M odels AGI- LP 1060-12-GG-240. 1. These power supplies have a single output that; complies with Class 2 output requirements. 2. These products are suitable for use in dry, damt and wet locations only. 3. The primary sides of these power supplies are suitable for connection with threaded type cenduit only. 4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top Of enclosure is kept at minimum 2 inches. 5. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for connection to liquid tight conduit fitting.