10180319_3831 S. BRISTOL - Plan - Laserfiche WebLink

Home Browse Search

17 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 3. When unitsi are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures. LED Lighting Modules, AION LED MODULE 500 SERIES. 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Cia$s 2 voltage and energy limited circuit and is rated greater than 15V DC. 3. These products are each rated max. 1 5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at li2 Volts DC o[ less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. LED Lighting Modules, Cat. No. AION LED MODULE 600 SERIES 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and Lenergy limited circuit and is rated greater than 12 V DC. 3. Thesej products are each rated max. 0.72 walts per module. When units are connected ta a Class 2 circuit, they are not to draw a total wattage of greater Ihan the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. Class 2 output LED drivers. Models D60-Ml, [)60-M. 1. These products are to be usedi in maximum 50°C ambient. 2. These products are provided with Class 2 output. 3. These products are intended for used in a maximum 20 A branch circuit. 4. These products are intended for use in dry and damp locations only. 5. These models are provided with 18 AWG input and output leads. The suitability of the. wire shall be considered in end product use. 6. These LED drivers shall be grounded through its mounting ears when usedi in end products. 7. These LED drivers are to be used in fixed wiring equipment only. 8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 9. In the end product, LED Drivers shall be lOcated not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less than 4 inches (102 mm) apart when arranged otherwise. Class 2 output LED drivers, Models D100-M-24. D60-M-24, 1. When used in end product, the maximum temperature on case surface shall hot exceed the temperature hote as below: Model No.Degree, °C Tested ambient, °C D100-M-24 89 60 D60-M-24 90 60 2. These products are provided with Class 2 output. 3. These products .ale intended for used in a maximum 20 A branch circuit. 4. These products are intended for use in dry and damp locations only. 5. These models are provided with No. li8 AWG input and min. No. 22 AWG output leads. The suitability of the wire shall be considered in end product use. 6. These LED drivers shall be grounded through its mounting ears when used in end products. 7. These LED drivers are to be used in fixed wiring equipment only. 8. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 9. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. Class 2 output LED drivers, Models 0100-X-24, D100«4-24. 1. These drivers with metallic housing or display/keys are to be used in the suitable end product fire enclosure. 2. These products are intended for used in a maximurh 20 A branch circuit. 3. These products are intended for use in dry and damp locations. 4. These LED drivers shall be grounded through its mounting ears when used in end product. 5. These models are provided with No. 18 AWG input and min. No. 22 AWG output leads. The suitability of the wire shall be determined in end product use. 6. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 7. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end=to-end. and not less than 4 inches (102 mm) apart when arranged othefwise. Class 2 LED modules, AION LED MODULE 500 SERIES or K and XX may be any alphanumeric characters. 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit and is rated greater than 15 V DC. '3. These products are each rated max. 1.5 watts per module. When units are conrected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. Class 2 LED modules, AION LED MODULE 600 SERIES. 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.