10180721_1500 AUTOMALL - Plan - Laserfiche WebLink

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM)152 10a. Models VL-nlOONS have been evaluated for a maximum amount of LEDs, per the following table: n - LED Color Quantity of LED Modules Quantity of LEDs W - White 105 210 ICW - Cool White 105 210 VWV - Warm Whit 105 210 R - Red 135 270 B - Blue 105 210 G - Green 105 210 A - Amber (Yellow)105 210 RO - Red Orange 135 270 Any Alphanumeric Character 105 210 11. LED Strings are intended to be series connected only. No parallel connections or interconnections of power supply circuits shall be made. 12. The adhesive is suitable for securement to the following materials: Aluminum, Galvanized Steel, Stainless Steel, Enameled Steel, Nickel Coated ABS, Glass (with or without Silane Coating), PVC, Glass/Epoxy, PBT, Polycarbonate, Acrylic/Polyurethane Paint, Polyester Paint or Ceramic. For other materials where suitability of securement has not been determined, the adhesive shall be submitted for evaluation or the LED module shall be secured by an additional suitable mechanical means. 13. LED model numbers may be followed with another suffix added to the end of the model number name. The suffix format will be "-letter". This suffix represents improved versions of LEDs whereby they exhibit a greater Efficacy (lumenstwatt) than the original LED. There would be no increase in heat dissipated or more energy used. The maximum forward voltages and current through the LED would remain the same or be less than as stated in this report. For Example: Model VL-MOO may be provided with a suffix such as VL-W100-b. Where the "-b" represents a brighter LED (126 Im/W compared to 100 Im/W) for the same power dissipated) LED drivers other than Class 2, Models VLP 100[)-U, VPL200D-U. 1. These LED Drivers comply with other than Class 2 output requirements. 2. These products are provided with the following electrical ratings: Input Output Model No.Vac Hz A Vdc A VLP100D-U 100-277 50/60 0.5 400 0.125 VPL200D-U 100-277 50/60 .60 250 .250 3. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end, and 101.6 mm (4 in.) from side to side. 4. These products shall be enclosed in the end product. 5. These products are suitable for factory wiring only. 6. These products have been tested in an oven at max. 40°C ambient. 7. These products are intended for use in dry or damp locations only. 8. The suitability of input/output leads and the wiring shall be determined in the end product use. 9. These products are constant current type that require the proper number of LED modules and controllers that do not exceed the maximum output voltage. 10. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 11. These LED drivers are intended for use in fixed equipment only. VERSEIDAG-INDUTEX GMBH INDUSTRISTRASSE 56 POSTFACH 2906 04150 KREFELD, GERMANY E219382 Flexible sign face material, designated "Seemee IV'. 1. Suitable for outdoor use. 2. Not suitable for use as an electrical enclosure. 3. Base color white. 4. Minimum thickness 0.015 in. (0.38 mm), minimum thickness 0.021 in. (0.53 mm) when secured with Recognized Component ABC Sign Products tensioning systems. 5. Any dimension greater than 6 feet needs braces to prevent billowing. 6. Suitable for use with all Recognized Component Securement and Tensioning systems. 7. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions. VINTECH INDUSTRIES E318117 611 INDUSTRIAL PARK DR IMLAY CITY, MI 48444 Aluminum Reinforced Thermoplastic Sign Trim Cap, Type Channel Trim. 1. Acceptable for use in wet locations. 2. Water exclusion must be determined in the end product. 3. Minimum 5 cm (2 in.) spacing from heat producing components required. 4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives may be applied for the final bond. Sign Face Generic Material Solvent Final Bond Adhesive Sign Trim Generic Material