10180014_4426 W. 1ST - Plan (2) - Laserfiche WebLink

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM)114 2. T.hese products with Class 2 outputs are suitable for use in dry, damp ahd wet locations. 1 3. In the end product, power supply spacing to other heat producing components shall be minimum=4 inches spacing to sidewalls, , and minimum 2 inches spacing to top of enclosure 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary and secondary circuits. LED Power Supply with Class 2 outputs. Models 250-12DC-DIM, 250-120(-DIM-240. 250-12DC-DIM-277,250-12DC, 250- XXXDC(a), 250-12DC-277, 250-1200-240. PCDK01, PCDK02, PCDK03, PCDK04 and P8675. 1. These products are suitable for dry and damp locations. 2. These Led Drivers do not need to be enclosed in the end product. 3. Theoutput(s) of these LED drivers comply with the criteria for Class 2 output, LED Power Supply with Class 2 outputs, Models 60-XXXD, 60-XXDC, 60-XXDC-DIM, 60-XXD-U, 37-XXXDC-DIM, 37-XXDC, XX can be any number from 00 to maximum 12 indicating output DC voltages. 1. These products are intended for use only in applications that comply with the requirements of the end product. 2. When marked as suitable for use in damp locations, these products are to be installed where protected from rain, snow and water spray by water shield or sign body. 3. These products shall have iconductors entering, leaving or residing in the wiring compartment or junction box extending at least 150 mm (6 in) inside. 4.. Power supply spacing to other heat producing components shall be mihimum 4 inches when minimum spacihg to sidewalls and top of enclosure is kept at minimum 2 inches. 5. Leakage current test shall be conducted if used in a portable end product. LED Power Supply with Ciass 2 outputs, Model 20-1206-A-100277. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief on input lead construction and Impact Tests have not been investigated. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure The flame class of polymeric. enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product. 7. When conducting temperature test in the end product, the maximum temperature on the enclosure (case) shall not exceed 80°C. When provided with alternate enclosure material R/C (QMFZ22), Teijin Chemicals Ltd. (E50075), Material designation LN-1250G, the maximum temperature on the enclosure (case) shall not exceed 90°C. LED Power Supply with Class 2 outputs, Model 40-12DC-A-100277. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015, No. 18 AWG, rated VW-1,600 V, 105'C. Output leads; are Style 1430, No. 18 AWG, rated VW-1, 300 V, 105°C. The suitability of the input and output connections shall be determined ih each end use application. 4. These power units are intended fordry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-0 and the necessity of additional fire barriers shall be determined in end product. Class 2 Letter Signs Cat. Nos. Model 800 Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2,12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. ;Class 2 LED Illumination, "Photocell" PL746-TPC is rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locatiOns. 5. These products are not required to be enclosed or protected from weather. LED Drivers, Model No. PCDH03. 1. The outputofthese LED drivers comply with the criteria for Class 2 output. 2. The product is suitable for use in dry or damp locations. 3. The product shall be enclosed in the end product in a suitable electrical, mechanical and fire enclosure. 4. The mounting means on metal housing is considered as grounding means. 5. The product is intended to be connected to max. i20 A branch circuit. 6. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 7. The input/output leads on these products are for factory connection only, not for Field Wiring. The suitability of the wiring is to be determined in end product. 8. The input leads were not provided with strain relief means, the suitability is to be determined in end product. 9. The LED driver has electrical rating below: < Input (Ap Output (DC), Loaded ICat. No.Current Frequency Voltage CurrentVoltage PCDH03 90-240 1.4 A max. 50/60 Hz 12V 5.0 A Class 2'LED Module, Cat. Nos P F S C 1 6, P F S C 1 7, P F S C 1 8. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 12 V.