Laserfiche WebLink
am L"VD FE&442*biARMOON*IT#866 18-at ..Deitish@etsj mmem <br />A HIGI GROUP [0824·1··· <br />SolarMount Mid Clamp <br />Part No. 302101 C, 302101 D, 302103C, 3021040, <br />302105D, 3021060 <br />0 <br />Bolt <br />Mid 4=/abge Nuk-: ,»52 <br />Mid clamp material: One of the following extruded aluminum <br />alloys: 6005-T5, 6105-T5, 6061-T-6 <br />Ultimate tensile: 38ksi, Yield:.35 ksi <br />Finish: Clear or Dark Anodized <br />Mid clamp weight: 0.050 lbs (23g) <br />Allowable and design loads are valid when components are <br />assembled according to authorized UNIRAC documents <br />· Values represent the allowable and design load capacity of a single <br />mid clamp assembly when used with a SolarMount series beam to <br />retain a module in the direction indicated <br />· Assemble mid clamp with one Unirac W'-20 T-bolt and one W'-20 <br />ASTM F594 serrated flange nut <br />Use anti-seize and tighten to 10 ft-lbs of torque <br />Resistance factors and safety factors are determined according to <br />part 1 section 9 of the 2005 Aluminum Design Manual and third- <br />party test results from an IAS accredited laboratory <br />Applied Load Average Allowable Safety Design Resistance <br />1.00 DISTANCE - -Direction Ultimate Load Factor,Load Factor,PE=.VEEN MCCULES ,. n ..lbs (N)lbs (N)FS lbs (N) * <br />1-F Tension, Y+2020 (8987)891 (3963)2.27 1348 (5994)0.667 <br />Transverse, Zi 520 (2313)229 (1017)2.27 346 (1539) - 0.665 <br />Y Sliding, Xi:1194 (5312)490 (2179)2.44 741 (3295) '0.620 <br />A <br />-X <br />Dimensions specified in inches unless noted <br />SolarMount End Clamp <br />Part No. 302001 C, 302002C, 3020020, 302003C, <br />3020030,302004C, 302004D, 302005C, 3020050, <br />302006C, 302006D, 302007D, 302008C, 302008D, <br />302009C, 302009D, 302010C, 302011 C, 302012C <br />-'.*M. » Wd#Li/&*92*- -7\\-End Clamp1 X 3/ <br />- Ser rated /<2/Flange Nut A <br />Y <br />A <br />D-X <br />• End clamp material: One of the following extruded aluminum <br />alloys: 6005-T5, 6105-T5, 6061-T6 <br />· Ultimate tensile: 38ksi, Yield: 35 ksi <br />· Finish: Clear or Dark Anodized <br />· End clamp weight: varies based on height -0.058 lbs (269) <br />Allowable and design loads are valid when components are <br />assembled according to authorized UNIRAC documents <br />Values represent the allowable and design load capacity of a single <br />end clamp assembly when used with a SolarMount series beam to <br />retain a module in the direction indicated <br />Assemble with one Unirac W'-20 T-bolt and one %"-20 ASTM F594 <br />serrated nange nut <br />Use anti-seize and tighten to 10 ft-lbs of torque <br />Resistance factors and safety factors are determined according to <br />part 1 section 9 of the 2005 Aluminum Design Manual and third- <br />party test results from an IAS accredited laboratory <br />Modules must be installed at least 1.5 in from either end of a beam <br />Applied Load Average Allowable Safety Design Resistance <br />" Ultimate Load Factor,Loads Factor,Direction <br />lbs (N)lbs (N)FS lbs (N) 0 <br />1-Elc€; <br />915 Tension, Y+1321 (5876)529 (2352)2.50 800 (3557)0.605 <br />Sic[>utE <br />21 (92)Til[OMLS Transverse, Zi 63 (279)14 (61)4.58 0.330 <br />Sliding, Xi <br />Dimensions specifiEd:iN·ibch-65 utilisi-7-6ted <br />142 (630)52 (231)2.72 79 (349)0.555 <br />0