Laserfiche WebLink
PANEL NL1A <br />120/208V 3ะค 4W. <br />FED FROM MDP <br />INFORMATION PLATE EQUIPMENT SERVED <br />LAMACOID PLATE <br />VOLTAGE <br />SOURCE OF POWER <br />PROVIDE I.D PLATE LABEL FOR ELECTRICAL <br />EQUIPMENT SUCH AS MAIN SWITCHGEAR, <br />SWITCHBOARD PANELBOARDS, AND <br />TRANSFORMERS <br />PROVIDE WARNING LABEL FOR <br />ELECTRICAL EQUIPMENT SUCH <br />AS MAIN SWITCHGEAR, <br />SWITCHBOARD PANELBOARDS, <br />AND TRANSFORMERS <br />Equipment Type 480V Switchgear <br />Grounding Grounded <br />Work Distance 11 inches (300 mm) <br />Availiable 3-Ph Bolted Current 25 kA <br />Flash Protection Boundary 27 inches <br />Incident Energy at 11 inches 4.39 cal/cm2 <br />Risk Category 2 <br />Equipment Name: Switchboard <br />Arc Flash Hazard <br />Appropriate PPE Required <br />WARNING! <br />GROUND BAR, INSULATORS, <br />BRACKETS AND BONDING, <br />PROVIDE BY E.C. <br />[12" LONG X 1/4" THICK X 4" HIGH] <br />#6 (AWG) OR LARGER BONDING CONDUCTOR TO EACH CONDUIT, WATER <br />IPE AND DUCT ENTERING ROOM. <br />#6 (AWG) OR LARGER BONDING CONDUCTOR TO EACH COMPUTER OR <br />TELECOMMUNICATIONS CABINET, RACK OR FRAME, DO NOT BOND RACKS. <br />CABINET AND FRAMES SERIALLY. <br />#6 (AWG) OR LARGER BONDING CONDUCTOR TO EACH CABLE LADDER, <br />CABLE TRAY AND CABLE WIREWAY IN OR ENTERING THE ROOM. <br />#6 (AWG) OR LARGER BONDING CONDUCTOR TO EXPOSED BUILDING <br />STEEL IN THE ROOM. <br />#6 (AWG) OR LARGER BONDING CONDUCTOR TO HVAC EQUIPMENT. <br />BONDING JUMPER GROUNDING. <br />KEYED NOTES:APPLY TO THIS DIAGRAM ONLY <br />1 <br />2 <br />3 <br />4 <br />5 <br />6 <br />SPECIALTY DEVICE OR <br />SWITCH <br />EXHAUST FAN <br />XXXXX-XX <br />ENGRAVED TEXT <br />ON COVERPLATE <br />WHEN REQUIRED <br />BY SPECIFICATIONS <br />OR WHEN NOTED <br />RECEPTACLES <br />XXXXX-XX <br />PANEL NAME <br />CIRCUIT NUMBER <br />SELF-ADHESIVE PERMANENT <br />TAPE WITH 12 POINT <br />HELVETICA MEDIUM LETTERING <br />LIGHT SWITCHES <br />XXXXX-XX (A,B) <br />ON LOW VOLTAGE SWITCHES <br />PROVIDE PANEL AND CIRCUIT <br />NUMBERS AS WELL AS RELAY <br />LETTER(S) SHOWN ON FLOOR <br />PLAN THAT ARE CONTROLLED <br />BY THAT SWITCH <br />TYPICAL CIRCUIT IDENTIFICATIONS: <br />NOTES: <br />1.REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION AND COLORS OF <br />TAPE REQUIRED FOR DIFFERENT SYSTEMS. <br />2.TEXT SHOWN ABOVE IS FOR EXAMPLE ONLY. MODIFY TEXT AS REQUIRED AS <br />MATCH INSTILLATION. <br />3.LABEL DEVICES IN SURFACE METAL RACEWAYS, POWER POLES, FLOOR BOXES, <br />4.WHERE MULTIPLE SWITCHES ARE GROUPED UNDER COMMON COVERPLATE AND <br />ARE SERVED FROM SAME CIRCUIT, PROVIDE ONLY ONE LABEL FOR MIDDLE <br />SWITCHED PROVIDE MULTIPLE LABELS IF DIFFERENT CIRCUITS ARE USED. <br />TO <br />P <br /> <br />O <br />F <br /> <br />T <br />V <br />. <br /> <br />G <br />C <br /> <br />T <br />O <br /> <br />C <br />O <br />O <br />R <br />D <br />I <br />N <br />A <br />T <br />E <br />5' <br /> <br />- <br /> <br />8 <br />" <br />CE <br />N <br />T <br />E <br />R <br />L <br />I <br />N <br />E <br /> <br />O <br />F <br /> <br />O <br />U <br />T <br />L <br />E <br />T <br />4' <br /> <br />- <br /> <br />0 <br />" <br />1' <br /> <br />- <br /> <br />3 <br />" <br />4" <br />1' <br /> <br />- <br /> <br />6 <br />" <br />GC TO VERIFY BLOCKING <br />WIDTH PER MOUTING <br />CEILINGHARDWARE OF SPECIFIED TV <br />CL <br />FLOOR <br />STUDS @ 24" O.C AT WALL MOUNT TV <br />LOCATION ONLY <br />SHEET METAL STRAPPING OVER STUDS <br />BEHIND DRYWALL IN HATCHED AREA <br />SHOWN <br />APPROX. OUTLINE OF MOUNTING <br />HARDWARE (BY OWNER) <br />APPROX. OUTLINE OF TV (BY OWNER); <br />TV SIZE IS 50" FOR LIVING ROOMS. <br />MUD RING FOR CABLE CHASE <br />RECESSED POWER/DATA/CABLE OUTLET <br />CONCEALED CONDUIT. PACK WITH <br />FIRE BARRIER MOLDABLE PUTTY AS <br />REQUIRED AT RATED PARTITIONS <br />MUD RING FOR CABLE CHASE <br />(LOCATION TO BE CENTERED IN OPEN <br />CABINET SHELVING) <br />POWER/DATA/CABLE OUTLET <br />(LOCATION TO BE CENTERED IN OPEN <br />CABINET SHELVING) <br />4' <br />- <br />0 <br />" <br />PLAN AT ELECTRICAL ROOM SWEEP <br />NOTES: <br />1.HORIZONTAL AND VERTICAL CONDUIT IS NOT ALLOWED WITHIN <br />4'-0" OF ANY COLUMN FACE. <br />2.NO ALUMINUM OF ANY KIND SHALL BE PLACED IN THE SLAB. <br />3.CONDUIT SHALL BE PLACED TO PROVIDE AT LEAST 3 TIMES THE <br />CONDUIT DIAMETER CLEAR BETWEEN PARALLEL CONDUITS. <br />4.CONDUIT SHALL BE LAID OUT TO NOT CROSS OVER OTHER <br />CONDUIT AND TO THE EXTENT POSSIBLE, BE AT LEAST 4" FROM <br />ANY REBAR OR POST-TENSIONING TENDONS. <br />5.DO NOT TIE CONDUIT TO REBAR OR POST-TENSIONING TENDONS <br />THAT RUN PARALLEL TO THE CONDUIT. <br />2" <br /> <br />C <br />L <br />R <br />MI <br />N <br />4'-0" <br />MIN. <br />4' <br />- <br />0 <br />" <br />10'-0" MAX <br />SPLAY CONDUIT. DO NOT <br />CROSS CONDUIT LINES <br />REBAR TO RUN 8'-0" MIN <br />PAST 6" CLR SPACING <br />SECTION X-X <br />MAXIMUM OUTSIDE DIAMETER OF <br />ANY CONDUIT THAN SCHED 40 <br />STEEL CONDUIT IS 1". <br />MAXIMUM OUTSIDE DIAMETER OF <br />SCHED 40 STEEL CONDUIT IS THE <br />LESSER OF 2 1/4" AND 1/3 THE <br />SLAB THICKNESS <br />WALL PER PLAN <br />WHERE OCCURS <br />WALL PER PLAN <br />WHERE OCCURS <br />MAX 2 1/4" CONDUIT <br />LOCATE CONDUIT IN MIDDLE <br />1/3 OF SLAB THICKNESS <br />T/ <br />3 <br />T/ <br />3 <br />T/ <br />3 <br />T MA <br />X <br />3 TIMES THE CONDUIT <br />DIAMETER CLEAR BETWEEN <br />PARALLEL CONDUITS <br />REQUIRED CONDUIT CLEARANCE <br />T/ <br />3 <br />T/ <br />3 <br />T/ <br />3 <br />T MA <br />X <br />LOCATE CONDUIT IN MIDDLE <br />1/3 OF SLAB THICKNESS <br />#5 @12" O.C. <br />TIOP & BOTT. <br />EA. WAY <br />SECTION Y-Y <br /> GENERAL NOTES: <br />PLASTIC OR METAL CONDUITS MAY BE EMBEDDED IN SLAB PROVIDING <br />THAT THE FOLLOWING CRITERIA ARE MET: <br />A - PIPES AND ELECTRICAL CONDUITS SHALL NOT BE EMBEDDED IN <br />STRUCTURAL CONCRETE EXCEPT WHERE SPECIFICALLY APPROVED BY <br />THE ENGINEER. MAXIMUM PIPE SIZE SHALL BE 1" DIA. AND LOCATED <br />WITHIN THE MIDDLE THIRD OF THE SLAB MINIMUM SPACING SHALL BE SIX <br />(6) TIMES THE PIPE DIAMETER. PIPES SHALL NOT IMPAIR THE STRENGTH <br />OF THE MEMBER. PROVIDE CONDUIT LAYOUT FOR ENGINEER REVIEW <br />AND APPROVAL. ANY GROUP OF CONDUITS LARGER THAN 2" & <br />CLOSER THAN 6" SHALL BE CONSIDERED AS AN OPENING AND SPECIALLY <br />TRIM BARS ARE TO BE PLACED AROUND THEM. <br />B - CONDUITS MUST NOT INTERRUPT THE POST-TENSIONED CABLES. <br />C - COLUMN CAPS SHOULD BE AVOIDED OR SPECIAL REINF. SHALL BE <br />PROVIDED BY THE E.O.R. <br />D - IT IS UNDESIRABLE TO HAVE EXCESS AMOUNTS OF CONDUIT <br />ENTERING THE SLAB AT ONE LOCATION. IF THIS CONDITION EXISTS, THE <br />CONDUITS MUST BE FANNED OUT <br />IMMEDIATELY. <br />ON/OFF <br />TYPICAL SENSOR SWITCH, <br />SINGLE CONTROL ZONE <br />PIR OCC <br />SENSOR <br />S1 S2 <br />ON <br />OFF <br />TYPICAL DIMMER SWITCH, <br />2-BUTTON FOR <br />SINGLE CONTROL ZONE <br />WITH DIMMING <br />DIMMER <br />S3 <br />ON <br />OFF <br />ON <br />OFF <br />TYPICAL DIMMER SWITCH, <br />4-BUTTON FOR <br />MULTIPLE CONTROL ZONE <br />WITH DIMMING <br />NOTES <br />1. TYPICAL SWITCHBANK CONFIGURATIONS SHOWN. EACH ZONE SHOWN ON PLAN SHALL HAVE A DEDICATED BUTTON CONTROL. <br />2. EACH SWITCHBANK SHALL HAVE CAPABILITY TO SWITCH ON/OFF ALL LIGHTING ZONES CONTROLLED BY SAME SWITCHBANK. <br />3. PROVIDE # OF BUTTONS AS REQUIRED. UNUSED BUTTONS SHALL BE SPARES. <br />4.COORDINATE WITH OWNER AND ARCHITECT FOR ENGRAVING OF BUTTONS AND FACEPLATES. COORDINATE FINAL FINISHES <br />WITH ARCHITECT. COORDINATE OWNER FOR IR INDICATOR OPTION AT WALL STATIONS. <br />4. REFER TO LIGHTING CONTROL SEQUENCE OF OPERATIONS FOR ADDTIONAL INFORMATION <br />TYPICAL WALL STATIONS FOR ENCLOSED ROOMS <br />ROOF RECEPTACLE DETAIL <br />SCALE: NO SCALE <br />ELEVATION <br />. <br />46 <br />0 <br /> <br />m <br />m <br />(1 <br />8 <br />' <br />' <br />) <br /> <br />M <br />A <br />X <br />CAST METAL <br />"WHILE-IN-USE" <br />WP COVER(S) & <br />RECEPTACLE(S). <br />REGID STEEL CONDUIT <br />FOR SUPPORT PER <br />N.E.C ART. 314 <br />REGID STEEL <br />CONDUIT FOR <br />WIRING <br />CAST METAL, 2-GANG, <br />NEMA 3R JUNCTION BOX <br />WITH THREADED HUBS. <br />SECTION "A-A"30 <br />5 <br /> <br />m <br />m <br />(1 <br />2 <br />' <br />' <br />) <br /> <br />M <br />A <br />X <br />A <br />A <br />ROOF PENETRATION AND <br />CONDUIT SUPPORT PER <br />DETAIL 3/45-ES-12 <br />PC COMMENTS RESPONSE #1 01/29/2025A <br />al <br />l <br /> <br />i <br />d <br />e <br />a <br />s <br />, <br /> <br />d <br />e <br />s <br />i <br />g <br />n <br />s <br /> <br />a <br />n <br />d <br /> <br />p <br />l <br />a <br />n <br />s <br /> <br />r <br />e <br />p <br />r <br />e <br />s <br />e <br />n <br />t <br />e <br />d <br /> <br />b <br />y <br /> <br />t <br />h <br />i <br />s <br /> <br />d <br />r <br />a <br />w <br />i <br />n <br />g <br /> <br />a <br />r <br />e <br /> <br />t <br />h <br />e <br /> <br />e <br />x <br />c <br />l <br />u <br />s <br />i <br />v <br />e <br /> <br />p <br />r <br />o <br />p <br />e <br />r <br />t <br />y <br /> <br />o <br />f <br />Go <br />u <br />v <br />i <br />s <br /> <br />E <br />n <br />g <br />i <br />n <br />e <br />e <br />r <br />i <br />n <br />g <br /> <br />a <br />n <br />d <br /> <br />s <br />h <br />a <br />l <br />l <br /> <br />n <br />o <br />t <br /> <br />b <br />e <br /> <br />r <br />e <br />p <br />r <br />o <br />d <br />u <br />c <br />e <br />d <br /> <br />i <br />n <br /> <br />w <br />h <br />o <br />l <br />e <br /> <br />o <br />r <br /> <br />i <br />n <br /> <br />p <br />a <br />r <br />t <br /> <br />w <br />i <br />t <br />h <br />o <br />u <br />t <br /> <br />t <br />h <br />e <br /> <br />e <br />x <br />p <br />r <br />e <br />s <br />s <br /> <br />p <br />r <br />i <br />o <br />r <br /> <br />w <br />r <br />i <br />t <br />t <br />e <br />n <br /> <br />p <br />e <br />r <br />m <br />i <br />s <br />s <br />i <br />o <br />n <br /> <br />o <br />f <br /> <br />s <br />a <br />i <br />d <br /> <br />e <br />n <br />g <br />i <br />n <br />e <br />e <br />r <br />s <br />, <br /> <br />a <br />n <br />y <br /> <br />u <br />n <br />a <br />u <br />t <br />h <br />o <br />r <br />i <br />z <br />e <br />d <br /> <br />r <br />e <br />u <br />s <br />e <br /> <br />o <br />f <br /> <br />t <br />h <br />e <br />s <br />e <br /> <br />p <br />l <br />a <br />n <br />s <br /> <br />o <br />t <br />h <br />e <br />r <br /> <br />t <br />h <br />a <br />n <br /> <br />f <br />o <br />r <br /> <br />t <br />h <br />e <br /> <br />p <br />r <br />o <br />j <br />e <br />c <br />t <br /> <br />a <br />n <br />d <br /> <br />l <br />o <br />c <br />a <br />t <br />i <br />o <br />n <br /> <br />s <br />h <br />o <br />w <br />n <br /> <br />i <br />s <br /> <br />p <br />r <br />o <br />h <br />i <br />b <br />i <br />t <br />e <br />d <br />. <br />JOB NO. <br />SUBMITTAL <br />DATE <br />SHEET TITLE <br />SHEET NO. <br />CLIENT: <br />REVISION <br />DATE <br />21 <br />3 <br />0 <br /> <br />E <br /> <br />4 <br />T <br />H <br /> <br />S <br />T <br /> <br /># <br />2 <br />0 <br />0 <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br />, <br /> <br />C <br />A <br /> <br />9 <br />2 <br />7 <br />0 <br />5 <br />BSB: MR230056; Gouvis: 66467 <br />WATER REVISIONS <br />09/12/2025 <br />1ST PLAN CHECK SUBMITTAL 08/20/2024 <br />2ND PLAN CHECK SUBMITTAL 1/29/2025 <br />PC COMMENTS RESPONSE #2 04/17/2025B <br />3RD PLAN CHECK SUBMITTAL 04/17/2025 <br />PC COMMENTS RESPONSE #3 07/10/2025C <br />4TH PLAN CHECK SUBMITTAL 07/10/2025 <br />WATER REVISIONS 09/12/2025D <br />WATER REVISIONS 09/12/2025 <br />PC COMMENTS RESPONSE #4 10/10/2025E <br />CLIENT REVISIONS 10/10/20251 <br />OL <br />I <br />V <br />E <br /> <br />C <br />R <br />E <br />S <br />T <br /> <br />R <br />E <br />S <br />I <br />D <br />E <br />N <br />T <br />I <br />A <br />L <br />21 <br />5 <br />0 <br /> <br />E <br />. <br /> <br />F <br />O <br />U <br />R <br />T <br />H <br /> <br />A <br />N <br />D <br /> <br />2 <br />1 <br />6 <br />0 <br /> <br />E <br />. <br /> <br />F <br />O <br />U <br />R <br />T <br />H <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br /> <br />C <br />A <br /> <br />9 <br />2 <br />7 <br />0 <br />5 <br />OL <br />I <br />V <br />E <br /> <br />C <br />R <br />E <br />S <br />T <br />DATE SIGNED: 7/8/25 <br />E-0.3B <br />DETAILS <br />TYPICAL SYSTEM GROUNDING AND BONDING 12ROOF RECEPTACLE DETAIL3TYPICAL TELECOM GROUND BUS DETAIL4TYPICAL LIGHTING CONTROL WALL STATIONS <br />DEVICE AND SWITCH LABELING 56LIVING ROOM/BEDROOM TV DETAIL7REINFORCING AND CLEARANCES AT CONDUIT IN SLAB <br />SWITCHBOARD, PANELBOARD AND