Laserfiche WebLink
11 Energize the System <br />a. Turn ON the AC disconnect or circuit beaker <br />for the branch drcuit. <br />b. Turn ON the main utility-grid AC circuit breaker. <br />Your system will start producing power after a <br />five-minute wait time. <br />-Trr- <br />-- status: LED3. <br />*1 0 <br />E·. O <br />21,- <br />aJ <br />One minute after DC powef is ap- <br />plied, the status LED on the under- <br />side of each M215 will blink green six <br />times to jhdicate normal start up. <br />Next Step <br />Refer to the Envoy Communications Gateway Quick <br />/nsta# Guide tor intormation on Envoy® installation <br />and Enlighten® access. <br />Enphase Energy. Inc. <br />1420 N. McDowell Blvd. <br />Petaluma, CA 94954 <br />USA <br />inio@enphaseenergy corn <br />0 UShttp.Abvw·.enphase.crirn <br />@ <br />Step Details <br />0 <br />NOTE- Verify that AC voltage at the site is within range: <br />240 Volt AC Split Phase 208 Volt AC Three Phase <br />Ll t o 62 211 to 264 VAC Ll to L.2 i.0 LS 183 fe 229 VAC <br />Ll. I.2,:to N 106 to 132 VAC Ll. !22,113 to N 1063 to 1.32 VAO <br />WARNING: Only use electrical sys®n components approved <br />fer wet locations. <br />WARNING: Do NOT exceed the maximum number of micro- <br />inverters in an AC trench circuit as listed in the table below. <br />Each branch circuit must be pfotedted by a dedicated circuit <br />breaker ot 20 A or less. <br />Service type Max M215s per branch <br />2&0 VAC Split phase 17 <br />208 VAC three phase 25 <br />WARNING: Size the AC wire gauge te account for voliage drop <br />for both the branch circuit and all upstream conductora leading <br />back to [he PCC. See Circuit Calculations for M215 ar http:// <br />www.enphase.com/support. <br />e <br />WARNING: Allo:·v a minimum of 1.9 orn·(0.75") between the <br />roof and the microinverter. Also allow 1.3 cm (0.509 bet .·veen the <br />back of the PV module and the Tcp of [lie microinverter. <br />NOTE: Torque the microinverter fisteners te ithe values shown. <br />Donor over torque: <br />• 6 mm (1/4") mc:unting hai·dwate -5N m M5-5C i,·i-lbs) <br />• 8 mm (5/16"j mouniing hadware]-9Nm (80-85 in-lbs) <br />Using a f:ower scrav.,ddver iA hot recommended due to the risk <br />01 thread galling. <br />0 <br />NOTE: The AC output neutral is not bonded to-ground inside <br />the microjnverter. <br />NOTE: The M215 groundimg cleat can accommodates 6 to 8 <br />AWG conductor. Torque ille 10/32 grouncing cleat screw lo <br />2 N m (20-25 in-lbs]. Do not over torque. Ushg a power screw- <br />driver is not recommended due to the risk of thread galling. <br />0 <br />WARNING: Install scaling 'caps on all unused AC connectors <br />as these became live when the sysem is <br />energized by the utility. The IP67-rated Al disconnect <br />scaling caps are required for <br />prorection agaillst moisture ingress. <br />NOTE. To remove a seating c.api you wYa- <br />must use the Enphase disconnect tcol or FILL <br />a #2 Phillips screwdri,uer. ,F <br />0 <br />NOTE: The Engage Cable uses the folbwing wiring scheme. <br />240'Volt AC, Split Phase Wiring 2C8 Volt AC, Three Phase Wiring <br />Black- Ll Black - Ll <br />Red- L2 Red - L2 <br />White - Neutral Blue- CO <br />Green - Ground White - N€Utr =.1 <br />Gr,ge,1 - Ground <br />© 20 33 Enphase Energy':'Inc. All rights reseneEl. <br />todi <br />aic <br />t <br />O0