1601 N Bristol St - Phase 1 - Plan

Home Browse Search

CITY OF SANTA ANA a U) U U U) I U c c U) N N ii U 0 N O N 0 0- ELECTRICAL DEMOLITION GENERAL NOTES (WHEN APPLICABLE): 1. REFERENCE ARCHITECTURAL DRAWINGS FOR FULL EXTENT OF DEMOLITION WORK AND PHASING. NOTIFY ARCHITECT, ENGINEER AND OWNER, AS APPLICABLE, OF ANY CONFLICTS OR DISCREPANCIES BETWEEN DRAWINGS AND JOB SITE CONDITIONS PRIOR TO SUBMITTING BID. 2. COORDINATE DEMOLITION AND REMOVAL OF EXISTING ELECTRICAL EQUIPMENT AND LIGHTING SYSTEMS WITH ARCHITECTURAL PHASING DRAWING AND OWNER TO ALLOW NECESSARY SYSTEMS TO REMAIN OPERATIONAL DURING CONSTRUCTION. (NOTE: NOT ALL EXISTING/DEMOLISHED EQUIPMENT, LIGHT FIXTURES, DEVICES OR RACEWAYS WILL BE SHOWN ON THE DRAWINGS). COORDINATE ELECTRICAL REQUIREMENTS FOR REMODELED/RENOVATED SPACES WITH THE OWNER. 3. AVOID DAMAGING FACILITIES, INCLUDING EQUIPMENT, LIGHT FIXTURES AND DEVICES THAT ARE EXISTING TO REMAIN, NEW OR REUSED. REPAIR ALL DAMAGE CAUSED DURING WORK AT NO EXTRA COST TO THE OWNER. a. DISPOSE OF ALL ELECTRICAL EQUIPMENT, LIGHT FIXTURES, AND DEVICES SHOWN TO BE REMOVED, UNLESS NOTED OTHERWISE. COORDINATE WITH THE OWNER THE ITEMS TO BE SALVAGED, AND THE LOCATION FOR STORAGE. AVOID DAMAGING SALVAGED ITEMS DURING DEMOLITION WORK AND DURING TRANSPORT TO OWNER'S DESIGNATED STORAGE LOCATION. 5. WHERE ALTERATION OF ELECTRICAL EQUIPMENT, LIGHT FIXTURES, RACEWAYS OR WIRING DEVICES AFFECTS EXISTING SURFACES/FINISHES: REPAIR/PAINT AFFECTED SURFACE TO MATCH EXISTING ADJACENT SURFACE IN ACCORDANCE WITH OWNER REQUIREMENTS. MAINTAIN FIRE RATING OF ALL FLOORS/WALLS/CEILINGS THAT ARE RATED. 6. WHERE DEMOLITION WORK INTERRUPTS ELECTRICAL CONTINUITY OF CIRCUITS THAT ARE TO REMAIN IN USE, PROVIDE NECESSARY DEVICES AND RELATED CIRCUITRY TO MAINTAIN ELECTRICAL CONTINUITY IN ACCORDANCE WITH OWNER REQUIREMENTS. RECIRCUIT REUSED ELECTRICAL EQUIPMENT, LIGHT FIXTURES AND WIRING DEVICES PREVIOUSLY POWERED FROM DEMOLISHED EQUIPMENT TO NEW OR TEMPORARY EQUIPMENT AS NEEDED. 7. COORDINATE DISCONNECTION OF POWER TO EQUIPMENT BEING DEMOLISHED/REMOVED/RELOCATED WITH OTHER TRADES PRIOR TO START OF WORK. ALL ELECTRICAL EQUIPMENT, LIGHT FIXTURES, RACEWAYS, WIRING DEVICES AND RELATED CIRCUITRY NOT BEING REUSED SHALL BE REMOVED IN ALL ACCESSIBLE AREAS AND IN FLOORS/WALLS/CEILINGS THAT ARE TO BE REMOVED, UNLESS NOTED OTHERWISE. AS ALLOWED BY OWNER, UNUSED ELECTRICAL EQUIPMENT, RACEWAYS AND RELATED CIRCUITRY THAT ARE INACCESSIBLE MAY BE ABANDONED IN PLACE AND SHALL BE PERMANENTLY DISCONNECTED FROM ALL POWER SOURCES, INSULATED FROM CONTACT WITH OTHER LIVE ELECTRICAL WIRING/DEVICES, AND IDENTIFIED AT THE TERMINATIONS AS NO LONGER BEING IN SERVICE. 8. LOW VOLTAGE CABLES/WIRING NOT BEING REUSED SHALL BE REMOVED UNLESS IDENTIFIED FOR FUTURE USE. COORDINATE REQUIREMENTS WITH OWNER. CARE SHOULD BE TAKEN DURING THE REMOVAL PROCESS TO PROTECT THE EXISTING REUSED CABLES/WIRING FROM DAMAGE. VOLTAGE DROP SCHEDULE 120V BRANCH CIRCUITS: MAXIMUM CIRCUIT LENGTH; 3% MAX VOLTAGE DROP WIRE GAUGE #12 #10 #8 #6 #4 #3 3840 N/A N/A 69 110 174 220 3500 N/A N/A 76 120 191 242 3250 N/A N/A 82 130 206 -- 3000 N/A N/A 88 140 223 -- 2880 N/A 58 92 146 233 -- Lu �_ 2500 N/A 66 106 169 268 -- v 2250 N/A 74 118 187 298 -- U � z 1920 54 87 138 220 -- -- m 1800 58 92 148 234 -- -- 1500 70 111 177 281 -- i -- 1200 87 139 221 -- -- -- 1000 105 167 266 -- -- -- 700 150 238 -- -- -- -- VOLTAGE DROP SCHEDULE 208V/10 BRANCH CIRCUITS: MAXIMUM CIRCUIT LENGTH; 3% MAX VOLTAGE DROP WIRE GAUGE #12 #10 #8 #6 #4 #3 8320 N/A N/A 96 152 241 -- 7488 N/A N/A 106 169 269 -- D 6656 N/A N/A 120 190 302Lu -- �_ 5764 N/A N/A 138 220 -- - 4992 N/A 100 160 253 -- -- v 4160 N/A 120 192 304 m3328 94 150 240 -- -- -- 2080 151 251 -- -- -- -- 1456 216 -- -- -- -- -- VOLTAGE DROP SCHEDULE 208V/30 BRANCH CIRCUITS: MAXIMUM CIRCUIT LENGTH; 3% MAX VOLTAGE DROP WIRE GAUGE #12 #10 #8 #6 #4 #3/0 36000 N/A N/A N/A N/A N/A 452 14411 N/A N/A 111 176 280 -- F- 11528 N/A N/A 138 220 -- -- w 9727 N/A N/A 164 260 -- -- U < 8646 N/A 116 185 292 -- -- U Q 7205 N/A 139 222 -- -- -- 5764 109 174 277 -- -- -- 11 4323 146 232 -- -- -- -- 3602 175 279 -- -- -- -- 2882 219 -- -- -- -- -- VOLTAGE DROP NOTES A. THE CONDUCTORS FOR FEEDER AND BRANCH CIRCUITS COMBINED SHALL BE SIZED FOR A MAXIMUM OF (5) PERCENT VOLTAGE DROP TOTAL. B. THE VOLTAGE DROP OF THE SERVICE FEEDERS SHALL NOT EXCEED (2) PERCENT. (CONTRACTOR TO VERIFY FEEDER LENGTH IN FIELD, UPSIZE FEEDER CONDUCTOR SIZE AS NEEDED, KEEP VOLTAGE DROP BELOW (2) PERCENT.) C. THE VOLTAGE DROP OF ANY BRANCH CIRCUIT SHALL NOT EXCEED (3) PERCENT. D. CONTRACTOR TO DETERMINE THE LENGTH OF RUN AND THE CONNECTED LOAD FOR EACH BRANCH CIRCUIT. USING THE VOLTAGE DROP SCHEDULES IN THIS DETAIL, THE CONTRACTOR SHALL DETERMINE THE SIZE OF THE BRANCH CIRCUIT CONDUCTOR IS ADEQUATE FOR A VOLTAGE DROP LESS THAN THE MAXIMUM (3) PERCENT. CONTRACTOR TO UP -SIZE THE BRANCH CIRCUIT CONDUCTORS AS NEEDED TO ADJUST FOR VOLTAGE DROP. (:: .� VOLTAGE DROP SCHEDULE AND NOTE NO SCALE ELECTRICAL GENERAL NOTES: 1. EXISTING CONDITIONS WERE TAKEN FROM ORIGINAL DRAWINGS AND SITE VISITS AND MAY NOT REFLECT ACTUAL "AS -BUILT" CONDITIONS. VERIFY EXISTING CONDITIONS PRIOR TO SUBMITTING FINAL BID. COORDINATE NEW AND DEMOLITION WORK WITH ALL OTHER TRADES AND EXISTING CONDITIONS. 2. NOTIFY ARCHITECT, ENGINEER AND OWNER, AS APPLICABLE, IF ANY DANGEROUS CONDITIONS EXIST ON JOB SITE BEFORE ANY DEMOLITION OR REMODEL WORK BEGINS. 3. COORDINATE ANY NECESSARY POWER OUTAGES WITH THE LANDLORD AND OWNER AND MAKE EVERY ATTEMPT TO SCHEDULE DURING NON -BUSINESS OR OFF-PEAK BUSINESS HOURS TO MINIMIZE DISRUPTION TO BUSINESS OPERATIONS. REQUESTS FOR ELECTRICAL SHUTDOWNS OF THE LANDLORD'S EQUIPMENT SHALL BE BROUGHT IN WRITING TO THE ATTENTION OF THE LANDLORD AT LEAST 7 DAYS IN ADVANCE. SHUTDOWNS SHALL NOT BE PERFORMED WITHOUT WRITTEN APPROVAL FROM THE LANDLORD. 4. ALL ROOF PENETRATIONS, FLOOR CHASING OR CORE DRILLING SHALL REQUIRE THE SPECIFIC APPROVAL OF THE LANDLORD AND OWNER. ALL WORK IN COMMON AREAS, SHAFTS OR OTHER OWNER SPACES MUST BE SPECIFICALLY REVIEWED AND APPROVED BY THE LANDLORD PRIOR TO ANY WORK BEING PERFORMED. MINIMIZE DISTURBANCE TO OTHER BUILDING TENANTS. 5. FOR AREAS AND EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL: EXISTING ELECTRICAL EQUIPMENT AND CIRCUITRY MAY BE REUSED IF IN GOOD CONDITION AND NEW DESIGN REQUIREMENTS CAN BE MET; OTHERWISE REPLACE. 6. FOR AREAS AND EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL: REPAIR OR REPLACE ANY EXISTING DAMAGED OR RECALLED ELECTRICAL EQUIPMENT, LIGHT FIXTURES, WIRING DEVICES AND RELATED CIRCUITRY AND RESTORE ALL ELECTRICAL SYSTEMS TO PROPER WORKING ORDER. THE FINAL ELECTRICAL INSTALLATION SHALL BE FREE FROM ELECTRICAL DEFECTS TO THE SATISFACTION OF THE AHJ, OWNER, ARCHITECT AND ENGINEER. 7. FOR AREAS AND EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL: VERIFY CONDITION AND AGE OF EXISTING REUSED ELECTRICAL EQUIPMENT, LIGHT FIXTURES, CIRCUIT BREAKERS, FUSES, CONDUIT, SWITCHES AND RELATED WIRING. NOTIFY OWNER OF ANY ELECTRICAL EQUIPMENT, LIGHT FIXTURES AND WIRING AGED BEYOND ITS USEFUL LIFE AND REPLACE AS DIRECTED. THE MAXIMUM EXPECTED USEFUL LIFE SHALL NOT EXCEED THE FOLLOWING, (AS DATED FROM THE POINT OF MANUFACTURE), UNLESS APPROVED BY THE ENGINEER, MANUFACTURER AND OWNER: 20 YEARS FOR CIRCUIT BREAKERS, GENERATOR/UPS SYSTEMS AND LIGHT FIXTURES, 30 YEARS FOR TRANSFORMERS AND PANELBOARDS, 40 YEARS FOR SWITCHBOARDS AND OTHER ELECTRICAL EQUIPMENT. 8. FOR AREAS AND EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL: ELECTRICAL EQUIPMENT SHALL BE LOCATED SO THAT THE CODE REQUIRED MINIMUM WORKING CLEARANCE AND DEDICATED ELECTRICAL SPACE ARE MAINTAINED. EXISTING EQUIPMENT NOT MEETING CURRENT CODE CLEARANCE REQUIREMENTS MAY REMAIN IF ALLOWED TO REMAIN BY THE AHJ, ENGINEER AND OWNER. ELECTRICAL SUPPLEMENTAL SPECIFICATIONS: 1. PRIOR TO SUBMITTING BID, VISIT THE JOB SITE AND BECOME FULLY ACQUAINTED WITH THE EXISTING CONDITIONS. AS APPLICABLE, REVIEW THE LANDLORD CRITERIA, GENERAL NOTES, OTHER TRADE DRAWINGS AND SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS THAT MAY NOT BE CALLED OUT IN THIS PORTION OF THE CONSTRUCTION DOCUMENTS. NOTIFY ARCHITECT AND ENGINEER OF ANY CONFLICTS OR DISCREPANCIES PRIOR TO SUBMITTING BID. 2. ALL WORK SHALL CONFORM TO ALL LOCAL CODES AND ORDINANCES AS WELL AS APPLICABLE INDUSTRY STANDARDS. ALL EQUIPMENT SHALL BEAR LABELS FOR THE USE INTENDED BY AN AHJ ACCEPTED NATIONALLY RECOGNIZED TESTING LABORATORY (NRTL), SUCH AS UL OR ETL. THE FINAL ELECTRICAL INSTALLATION OF THE FACILITY OCCUPIED BY OWNER SHALL BE FREE FROM ELECTRICAL DEFECTS TO THE SATISFACTION OF THE AHJ, OWNER, ARCHITECT AND ENGINEER. 3. COORDINATE FINAL LOCATION AND INSTALLATION REQUIREMENTS OF ALL LIGHT FIXTURES, ELECTRICAL EQUIPMENT AND ELECTRICAL DEVICES WITH ARCHITECTURAL DRAWINGS, EXISTING CONDITIONS AND OTHER TRADES PRIOR TO ROUGH -IN. PROVIDE ALL NECESSARY DEVICES, CORDS, PLUGS, DISCONNECTS AND FINAL CONNECTIONS TO ELECTRICAL EQUIPMENT FOR PROPER OPERATION IN ACCORDANCE WITH CODE, OWNER AND MANUFACTURER REQUIREMENTS. 4. ELECTRICAL DRAWINGS ARE DIAGRAMMATIC/SCHEMATIC IN NATURE AND REPRESENT THE GENERAL SCOPE OF WORK. IT IS NOT WITHIN THE SCOPE OF THE ELECTRICAL DRAWINGS TO SHOW ALL NECESSARY RACEWAY ROUTING, BENDS, OFFSETS, PULL BOXES AND OBSTRUCTIONS. CONTRACTOR SHALL COORDINATE THE FINAL LOCATION OF EQUIPMENT AND WIRING DEVICES WITH OTHER TRADES PRIOR TO INSTALLATION AND INSTALL ALL WORK TO CONFORM TO THE OWNER REQUIREMENTS. 5. ALL CONDUCTOR AND CONDUIT LENGTHS SHOWN IN THESE DESIGN DOCUMENTS ARE INTENDED SOLELY FOR USE IN THE DESIGN CALCULATIONS BY THE DESIGN PROFESSIONAL, UNLESS NOTED OTHERWISE. LENGTHS SHOWN SHALL NOT BE USED TO ASSIST IN THE BIDDING TAKEOFF PROCESS. THE CONTRACTOR IS SOLELY RESPONSIBLE FOR THE MATERIAL QUANTITIES REQUIRED TO BID AND CONSTRUCT THE COMPLETE PROJECT. 6. PROVIDE PROPER FIRE PROOFING AND SEALANT FOR PENETRATIONS THROUGH FIRE RATED ASSEMBLIES. THE FIRE STOPPING METHOD, MATERIAL AND ITS APPLICATION SHALL BE NRTL LISTED, CODE COMPLIANT AND APPROVED BY AHJ. 7. FOR CAST -IN -PLACE CONCRETE, TILT -UP WALLS, PRECAST OR SIMILAR PRE-ENGINEERED WALL SYSTEMS: COORDINATE THE FINAL LOCATION OF ALL ELECTRICAL DEVICES, RACEWAYS, LIGHT FIXTURES AND PENETRATIONS WITH ARCHITECT, WALL SUPPLIER AND OTHER TRADES PRIOR TO WALL CONSTRUCTION. CONDUIT/RACEWAY IMBEDDED IN CONCRETE WALLS SHALL BE SCHEDULE 80 PVC OR LFMC; OTHER TYPES MAY BE ALLOWED IF APPROVED BY WALL SYSTEM MANUFACTURER AND ENGINEER. 8. ALL APPLICABLE SWITCHES, RECEPTACLES, OUTLETS, AND CONTROLS SHALL BE PLACED AT HEIGHTS THAT ARE IN ACCORDANCE WITH ADA ACCESSIBILITY GUIDELINES. 9. WIRING DEVICES ADJACENT TO EACH OTHER SHALL BE INSTALLED UNDER A SINGLE COVER PLATE, UNO. 10. WIRING DEVICES SHOWN BACK-TO-BACK ON A COMMON WALL SHALL BE OFFSET A MINIMUM OF 12" HORIZONTALLY TO REDUCE SOUND TRANSMISSION BETWEEN ROOMS, UNO. 11. ALL WP OUTLET BOX HOODS SHALL BE "EXTRA -DUTY" AND "WHILE -IN -USE COVER" TYPE. OUTLET BOX HOODS SHALL BE LOW PROFILE WHEREVER PRACTICABLE, UNLESS NOTED OTHERWISE. THE USE OF LARGE BUBBLE COVERS SHALL BE AVOIDED ON THE EXTERIOR OF THE BUILDING OR BEHIND EQUIPMENT IN ORDER TO PREVENT DAMAGE TO THE COVER AND TO ALLOW THE EQUIPMENT TO BE LOCATED CLOSE TO THE WALL. 12. ALL SINGLE-PHASE RECEPTACLES RATED 150 VOLTS TO GROUND OR LESS, 50 AMPERES OR LESS AND THREE PHASE RECEPTACLES RATED 150 VOLTS TO GROUND OR LESS, 100 AMPERES OR LESS INSTALLED IN LOCATIONS REQUIRED BY CODE (THIS INCLUDES BATHROOMS, KITCHENS/FOOD PREP AREAS, GARAGES, EXTERIOR LOCATIONS AND RECEPTACLES WITHIN 6 FEET OF A SINK). SHALL BE PROVIDED GROUND -FAULT CIRCUIT -INTERRUPTER PROTECTION FOR PERSONNEL PER N.E.C. 210.8 AND INSTALLED IN ACCORDANCE WITH N.E.C. 240,24. ALTERNATIVELY, A GFCI CIRCUIT BREAKER CAN BE INSTALLED.GFCI RECEPTACLES SHALL BE READILY ACCESSIBLE AND SHALL NOT BE LOCATED BEHIND STATIONARY EQUIPMENT. GFCI PROTECTION MAY BE VIA A GFCI CIRCUIT BREAKER OR GFCI RECEPTACLE, UNLESS NOTED OTHERWISE. WHERE NECESSARY, GFCI PROTECTION MAY BE ACHIEVED VIA A BLANK FACE GFCI DEVICE LOCATED IN A READILY ACCESSIBLE LOCATION NEAR RECEPTACLE BEING PROTECTED. FOR DOWNSTREAM WIRING DEVICES LOCATED ON THE SAME BRANCH CIRCUIT, THE GFCI PROTECTION MAY BE PROVIDED FOR BY A SINGLE UPSTREAM DEVICE IF ALL PROTECTED DEVICES ARE LABELED PER CODE.) 13. PROVIDE TAMPER -RESISTANT JR) TYPE RECEPTACLES AT ALL CODE REQUIRED LOCATIONS AND AT LOCATIONS WHERE RECEPTACLES ARE MOUNTED LESS THAN 5'-61, AFF AND ARE EASILY ACCESSIBLE BY CHILDREN, UNLESS NOTED OTHERWISE. 14. FLEXIBLE CONDUIT IS ONLY PERMITTED WHERE SPECIFICALLY ALLOWED IN THE CONSTRUCTION DOCUMENTS, WHERE CONCEALED FROM VIEW OR EXPOSED FINAL CONNECTIONS TO LIGHT FIXTURES AND EQUIPMENT IN LENGTHS OF 6-0" OR LESS. 15. ALL EMPTY CONDUIT/RACEWAY SHALL BE INSTALLED WITH PULL STRINGS. TERMINATE CONDUIT STUB -UP WITH A NYLON BUSHING. 16. EXPOSED CONDUIT/RACEWAY SHALL BE PAINTED TO MATCH ADJACENT SURFACE, UNLESS NOTED OTHERWISE. COORDINATE REQUIREMENTS WITH ARCHITECT AND OWNER PRIOR TO INSTALLATION. Plannin 17. CONDUITS/RACEWAYS SHALL BE CONCEALED FROM VIEW WHEREVER ACTICABLE, UNLESS NOTED OTHERWISE. ROUTE CONDUITS SERVING ROOFTOP EQL IPMENT CONCEALED INSIDE EQUIPMENT CURB AND MINIMIZE ROOF PENETRATIONS AND EXTERIOR CONDUIT RUNS WHERE PRACTICABLE. SUPPORT RACEWAY FROM STRUCTURE, NOT ROOF DECK. MAINTAIN 2" MIN SPACING FROM BOTTOM OF ROOF DECK TO PREVENT ROOFING SCREWS FROM PENETRATING RACEWAY. MO NOT ROUTE CONDUITS ACROSS SKYLIGHTS, ACCESS PANELS, HATCHED TILES, HVA DIFFFSIfS, R P OR EQUIPMENT WORKING CLEARANCE SPACE. ROUTE ALL EXPOSED N N-FL IB�f CONDUITS TIGHT TO STRUCTURE, PARALLEL TO BUILDING LINES AND IN STRUT OR CABLE/PIPE TRAY WHERE PRACTICABLE. INSTALL CONDUITS PLUMB/ LEI IEL WHERE EXPOSED TO VIEW. COORDINATE RACEWAY ROUTING AND INSTALLATI WITH OTHER TRADES PRIOR TO ROUGH -IN. 18. WHERE PRACTICABLE, ALL UNDER-FLOOR/UNDER-GROUND CONDUITS/ ACEWAY SHALL BE INSTALLED A MINIMUM OF 24" BELOW BOTTOM OF SLAB/PAVI /GRADE, UNLESS NOTED OTHERWISE. NOTE: THE DESIGN INTENT FOR INSTALLIN ftlgft r I CIRCUITRY AT THIS DEPTH IS TO PROTECT THE ELECTRICAL CIRCUITRY zT L ` DUE TO FUTURE WORK. 19. PROVIDE LABEL AT EACH RECEPTACLE COVER PLATE WITH THE RESPE T,Qate. "PNLBD-CKT#" DESIGNATION. COORDINATE LABEL REQUIREMENTS WITH THE OWNER PRIOR TO INSTALLATION. REFER TO THE SPECIFICATIONS FOR MORE INFORMATION. 20. MULTIWIRE BRANCH CIRCUITS ARE NOT ALLOWED, UNLESS NOTED OTH ERWISE. 21. PROVIDE INSULATED EQUIPMENT GROUNDING CONDUCTOR FOR ALL CIRCUITS, UNLESS NOTED OTHERWISE. 22. IF CONTRACTOR IS RESPONSIBLE FOR INSTALLING UTILITY TRANSFORMER PAD (FOR NEW UTILITY TRANSFORMER) REFER TO SERVING UTILITY'S GREEN BOOK FOR INSTALLATION REQUIREMENTS AND COORDINATE TRANSFORMER INSTALLATION WITH UTILITY COMPANY. SPECIAL SYSTEMS SUPPLEMENTAL SPECIFICATIONS: 1. PROVIDE NECESSARY BOXES, CONDUIT AND MAKE FINAL CONNECTIONS TO TEMPERATURE CONTROL DEVICES PER MANUFACTURER'S RECOMMENDATIONS. THIS INCLUDES BUT IS NOT LIMITED TO: MAIN CONTROL PANELS, THERMOSTATS, HUMIDISTATS, AC SOLENOIDS, HEAT RECLAIM WIRING, AHU CONTROL WIRING, DUCT FURNACE CONTROL WIRING, TIMERS, AND SIMILAR CONTROLS. PROVIDE CONDUIT FOR ALL WIRING WITHIN WALLS. PROVIDE CONTROL AND INTERLOCK WIRING WHEN NOT PROVIDED BY OTHER TRADES. COORDINATE REQUIREMENTS WITH EQUIPMENT SUPPLIERS AND OTHER TRADES PRIOR TO ROUGH -IN. 2. PROVIDE LINE VOLTAGE WIRING AND MAKE FINAL CONNECTIONS TO ALL DUCT -MOUNTED SMOKE DETECTORS, FIRE/SMOKE AND SMOKE DAMPERS WHERE APPLICABLE. COORDINATE REQUIREMENTS WITH OTHER TRADES PRIOR TO INSTALLATION. 3. DEVICES MOUNTED ON ACOUSTICAL TILE CEILINGS SHALL BE CENTERED ON THE TILE, UNO. 4. PROVIDE BOX AND 3/4" CONDUIT FROM EACH THERMOSTAT LOCATION TO MECHANICAL EQUIPMENT, (FLUSH MOUNT BOX WHEREVER PRACTICABLE). COORDINATE LOCATION OF ALL THERMOSTAT BOXES WITH MECHANICAL/CONTROLS CONTRACTOR AND OWNER PRIOR TO ROUGH -IN. 5. PROVIDE BOXES AND CONDUITS FOR THE FIRE PROTECTION SYSTEM LOW VOLTAGE WIRING AS REQUIRED. THIS INCLUDES EXPOSED WIRING LESS THAN 96" AFF. AT A MINIMUM, PROVIDE 3/4" CONDUIT, UNLESS NOTED OTHERWISE. COORDINATE REQUIREMENTS AND LOCATIONS WITH SYSTEM INSTALLER AND FIRE ALARM SPECIFICATIONS. 6. AT A MINIMUM, PROVIDE EXTRA DEEP, DOUBLE GANG COMMUNICATION OUTLET BOXES, (FLUSH MOUNTED WHEREVER PRACTICABLE), WITH SINGLE -GANG PLASTER RING AND 1" CONDUIT STUBBED -UP CONCEALED TO ACCESSIBLE CEILING SPACE, UNLESS NOTED OTHERWISE. PROVIDE SURFACE MOUNTED DATA BOXES WITHIN CABINETRY, AND SELECT OTHER LOCATIONS AS INDICATED ON THE DRAWINGS. COORDINATE TELEPHONE/DATA BOX AND CONDUIT LOCATIONS AND SIZES WITH OWNER AND OTHER TRADES PRIOR TO ROUGH -IN. 7. PROVIDE NYLON BUSHINGS FOR ALL COMMUNICATIONS AND LOW VOLTAGE WIRING CONDUITS AND SLEEVES, UNLESS NOTED OTHERWISE. 8. ALL COMMUNICATIONS AND LOW VOLTAGE WIRING CONDUIT SHALL BE INSTALLED WITH AN ACCESSIBLE PULLBOX BETWEEN EVERY 180 DEGREE CHANGE IN DIRECTION AND AT 100' INTERVALS OF CONTINUOUS RUNS. 9. MINIMUM BEND RADIUS FOR COMMUNICATIONS CONDUIT IS 6 TIMES THE INSIDE DIAMETER FOR CONDUITS 2" IN DIAMETER AND SMALLER AND 10 TIMES THE INSIDE DIAMETER FOR CONDUITS GREATER THAN 2" IN DIAMETER, UNLESS NOTED OTHERWISE. 10. LOW VOLTAGE COMMUNICATION, ENERGY MANAGEMENT, SOUND SYSTEM, SECURITY AND RELATED WIRING IS TO BE PERFORMED BY OTHERS UNDER A SEPARATE CONTRACT, UNLESS NOTED OTHERWISE. PROVIDE BOXES AND CONDUIT IN FINISHED AND RATED FLOORS/WALLS/CEILINGS TO ACCESSIBLE LOCATIONS FOR ALL LOW VOLTAGE WIRING. PROVIDE ALL LINE VOLTAGE CIRCUITRY (120V AND HIGHER) TO OWNER FURNISHED EQUIPMENT AND LOW VOLTAGE STEP-DOWN TRANSFORMERS AS REQUIRED. COORDINATE ELECTRICAL REQUIREMENTS AND LOCATIONS WITH SYSTEM INSTALLER AND OWNER. 11. ALL LOW VOLTAGE CLASS 2 OR 3 WIRING NOT IN CONDUIT SHALL BE PLENUM RATED WHERE APPLICABLE. 12. LOW VOLTAGE CABLE SHEATH LABELS AND RELATED MANUFACTURER INFO SHALL REMAIN APPARENT IN ALL EXPOSED APPLICATIONS. PROTECT ALL EXPOSED CABLING FROM PAINTING AND OVERSPRAY (INCLUDES CABLE NOT ROUTED IN CONDUIT AND THAT IS IN CABLE TRAY). 13. CABLES SHALL BE ROUTED THROUGH THE BUILDING CABLE TRAY/RACEWAY SYSTEM, UNLESS NOTED OTHERWISE. EXPOSED CABLING SHALL NOT BE ROUTED IN AREAS EXPOSED TO STRUCTURE UNLESS SPECIFICALLY PERMITTED BY THE OWNER. IN AREAS WHERE EXPOSED CABLES ARE ALLOWED, IT SHALL BE INSTALLED IN A NEAT AND WORKMAN LIKE MANNER IN ACCORDANCE WITH THE OWNER'S REQUIREMENTS. WHERE REQUIRED, PROVIDE CONDUIT TO ROUTE LOW VOLTAGE CABLING TO THE CABLE TRAY OR NEAREST ACCESSIBLE CEILING SPACE. 14. CONDUITS FOR COMMUNICATIONS OUTLETS SERVING ELEVATOR EQUIPMENT ROOMS, FACP, AND SIMILAR CRITICAL EQUIPMENT AS DESIGNATED BY THE OWNER SHALL BE CONTINUOUS ("HOMERUN") FROM OUTLET TO SERVING COMMUNICATIONS ROOM. SHEET INDEX CLICCT nC CrE:)I E)TIIIKI E0.1 ELECTRICAL GENERAL NOTES E0.2 ELECTRICAL SYMBOLS AND ABBREVIATIONS E0.3 ELECTRICAL SPECIFICATIONS E2.1 ELECTRICAL SITE POWER PLAN E2.2 ELECTRICAL SITE LIGHTING PLAN E4.1 ELECTRICAL SINGLE LINE AND PANEL SCHEDULE E5.1 TITLE-24 ENERGY COMPLIANCE FORMS APPLICABLE ELECTRICAL CODES: NOTE: PROJECT IS DESIGNED IN COMPLIANCE WITH THE FOLLOWING CODES. THIS IS NOT AN EXHAUSTIVE LIST. PROJECT SHALL COMPLY WITH ALL APPLICABLE CODES, STANDARDS AND LOCAL REQUIREMENTS. 2022 CALIFORNIA BUILDING CODE (CBC) 2022 CALIFORNIA ENERGY CONSERVATION CODE (CECC) 2022 CALIFORNIA ELECTRIC CODE (CEC) 2022 CALIFORNIA GREEN BUILDING CODE r Arch i t e c t u ra I Corporation 9431 HAVEN AVENUE, SUITE 212 RANCHO CUCAMONGA, CA 91730 P. 909.259.9971 1 F. 909.944.8409 www.AmorArch.com BRISTOL CENTER PROPERTIES LLC 714 S PLYMOUTH BLVD LOS ANGELES, CA 90005 AMIR HOURIANI aihouriani@gmail.com Nz r.16Y1i111111r_sLNN cv i E MECHANICAL I ELECTRICAL I PLUMBING CARLOS RIVAS carlos@rivasdesignconsultants.com Z Lu G O J W W W m Qo F_� O W N J OU E Q z z Q CD ~ �z U) w J F F H w w U) U) Lu O z J Q z Lu Q U Lu J Lu STAMP V C - 24421 8/31 /2025 * RENEWAL cSj DATE �TFOF CA1-�FO� DATE SIGNED: 08/13/2024 SHEETS BEARING THIS SEAL AND WET SIGNATURE ARE AUTHENTICATED. RESPONSIBILITY FOR ALL OLDER PLANS, SPECIFICATIONS OR INSTRUMENTS ARE DISCLAIMED. REVISIONS 0 0 0 0 0 DATE 2024.08.15 PROJECT NUMBER A2641 SHEET NUMBER 001 COPYRIGHT 2024 - DESIGNS, DRAWINGS AND SPECIFICATIONS ARE INSTRUMENTS OF SERVICE AND ARE THE PROPERTY OF THE DESIGN PROFESSIONAL. REPRODUCTION PROHIBITED WITHOUT THE EXPRESSED WRITTEN CONSENT OF THE DESIGN PROFESSIONAL.