Laserfiche WebLink
95 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 <br />temperature measured on top enclosure surface of was 66°C during the Temperature Test. This data shall be used to determine <br />the suitability of insulating materials in close proximity to these devices. <br />5. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, <br />and minimum 2 inches spacing to top of enclosure. <br />LED array drivers, Models LPV-20-5, LPV-20-12, LPV-20-15, LPV-20-24, LPC-20-350, LPC-20-700. <br />1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 <br />output. <br />2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and <br />wet locations. <br />3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, <br />and minimum 2 inches spacing to top of enclosure. <br />4. These products are provided with the following electrical ratings: <br />Input Output <br />]Model Vac A Hz Vdc A <br />LPV-20-5 100-240 0.55 50/60 5 3 <br />LPV-20-12 100-240 0.55 50/60 12 1.67 <br />|LPV-20-15 100-240 0.55 50/60 15 1.33 <br />|LPV-20-24 100-240 0.55 50/60 24 0.84 <br />LPC-20-350 100-240 0.55 50/60 48 0.35 <br />;LPC-20-700 100-240 0.55 50/60 30 0.70 <br />5. These products shall be enclosed in the end product. <br />6. These power supplies are suitable for use in dry and damp locations. <br />LED array drivers, Model CLy-60-z, where y can be G (with potting compound) or N (without potting compound), z can be 12,15, <br />20,24,27,36 or 48 for output voltage. Models PLN-60-z, PLN-45-z, where z can be 12,15, 20, 24, 27, 36 or 48 for output voltage, <br />without potting compound. <br />1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a max. of one Class 2 output. <br />2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and <br />wet locations. <br />3. In the end product, power supply spacing to other heat producing components shall be min. 2 inches spacing to sidewalls, and <br />min. 2 inches spacing to top of enclosure. <br />4. These products are provided with the following electrical ratings: <br />Input (ac)Output (dc) <br />Model V A Hz V A <br />CLy-60-12 100-240 0.8 50/60 12 5.0 <br />(y=G or N), PLN-60-12 277 0.3 <br />CLy-60-15 100-240 0.8 50/60 15 4.0 <br />(y=G or N), PLN-60-15 277 0.3 <br />CLy-60-20 100-240 0.8 50/60 20 3.0 <br />(y=G or N), PLN-60-20 277 0.3 <br />CLy-60-24 100-240 0.8 50/60 24 2.5 <br />(y=G or N), PLN-60-24 277 0.3 <br />CLy-60-27 100-240 0.8 50/60 27 2.3 <br />(y=G or N), PLN-60-27 277 0.3 <br />CLy-60-36 100-240 0.8 50/60 36 1.7 <br />(y=G or N), PLN-60-36 277 0.3 <br />CLy-60-48 100-240 0.8 50/60 48 1.3 <br />(y=G or N), PLN-60-48 277 0.3 <br />PLN-45-12 100-240 0.55 50/60 12 3.8 <br />277 0.22 <br />PLN-45-15 100-240 0.55 50/60 15 3.0 <br />277 0.22 <br />PLN-45-20 100-240 0.55 50/60 20 2.3 <br />277 0.22 <br />PLN-45-24 100-240 0.55 50/60 24 1.9 <br />277 0.22 <br />PLN-45-27 100-240 0.55 50/60 27 1.7 <br />277 0.22 <br />PLN-45-36 100-240 0.55 50/60 36 1.25 <br />277 0.22 <br />PLN-45-48 100-240 0.55 50/60 48 0.95 <br />277 0.22 <br />5. These products shall be enclosed in the end product. <br />6. These power supplies are suitable for use in dry and damp locations. <br />7. These products are suitable for factory wiring only. <br />LED array drivers, Model PLN-30-Y, where Y may be 9,12, 15, 20, 24, 27 or 36 for output voltage. <br />1. These LED Drivers comply with the Class 2 output requirements. <br />5