1430 E Edinger Ave-REV 1 - Plan - Laserfiche WebLink

Home Browse Search

PACKAGED GAS/ELECTRIC ROOFTOP UNIT SCHEDULE MARK MFR. AND MODEL NUMBER NOM. CAP. (TONS) LOC. E.S.P. (IN. WG.) EFFICIENCY AIRFLOW (CFM) MIN. O.A. (CFM) TOTAL CLG CAP. (MBH) TOTAL HTG. CAP.ELECTRICAL DATA POWER EXHAUST DRAIN SIZE (IN.) NET. WT. (LBS.)REMARKS EER SEER AFUE INPUT (MBH) OUTPUT (MBH)V./ PH./ HZ.MCA MOCP HP FLA LRA TRANE YHC060F3 OR APPROVED EQUAL 5.00 ROOF 0.8 12.9 15.0 80%2000.0 780.0 61.0 80.0 64.0 208-230/3/60 30 45 0.33 2.2 3.9 1-3/4" NPT 755 1 - 8 TRANE YHC036E3 OR APPROVED EQUAL 3.00 ROOF 0.8 12.7 15.0 80%1200.0 200.0 37.6 60.0 48.0 208-230/3/60 21 30 0.33 2.2 3.9 1-3/4" NPT 540 1 - 6, 8 REMARKS: 1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS. 2. PROVIDE WITH NEW T24 APPROVED PROGRAMMABLE THERMOSTAT. 3. PROVIDE WITH 2" THICK HIGH EFFICIENCY MERV-13 PLEATED PANEL FILTERS. 4. CONTRACTOR TO VERIFY IN FIELD THE SERVICEABILITY OF THE EXISTING ROOF CURB. REPLACE AS NECESSARY. 5. PROVIDE WITH PREMIUM EFFICIENCY MOTORS AND DISCONNECT SWITCH BY ELECTRICAL CONTRACTOR. 6. PROVIDE WITH POWER EXHAUST AND FACTORY INSTALLED FIXED DRY BULB TEMPERATURE ECONOMIZER WITH BAROMETRIC RELIEF. 7. PROVIDE WITH SMOKE DETECTORS AT THE SUPPLY SIDE TO CONNECT TO THE BUILDING FORE PROTECTION SYSTEM (IF APPLICABLE), AND SHUTDOWN AC WHEN ACTIVATED. IN CASE THERE IS NO EXISTING FIRE PROTECTION SYSTEM, NO NEED TO PROVIDE CONNECTION WITH SMOKE DETECTOR. 8. REPLACE EXISTING PACKAGED GAS/ELECTRIC ROOFTOP UNIT. 800-R 10"Ø NK A AIR DEVICE DATA TAG DIFFUSER MARK AIR QUANTITY (CFM) S=SUPPLY R=RETURN E=EXHAUST NECK SIZE EQUIPMENT TAG EQUIPMENT TAG NUMBER NOTE TO ALL BIDDERS: THE PROJECT IS NOT READY TO ISSUE (RTI). SOME ITEMS ARE SUBJECT TO CHANGE TO PLANCHECK COMMENTS AND CONTINUING COORDINATION. GENERAL NOTES FCU 4 EXISTING DUCTWORK OR EQUIPMENT TO BE REMOVED ABBREV.SYMBOL DESCRIPTION (D) (E)EXISTING DUCTWORK OR EQUIPMENT TO BE REMAIN 48x36 (N)NEW DUCTWORK OR EQUIPMENT. DUCT SIZE NOTATION W/SIZE OF NEAREST SIDE INDICATED FIRST CD SG RG EG CEILING SUPPLY DIFFUSER SUPPLY GRILLE RETURN AIR GRILLE OR REGISTER EXHAUST GRILLE MVD BDD FSD MANUAL VOLUME DAMPER BACKDRAFT DAMPER FIRE SMOKE DAMPER T TSTAT THERMOSTAT POS POINT ON CONNECTION SD SD SMOKE DETECTOR ARCH ABV AFF BEL BOT CD CFM FT OBD N.T.S NK TYP UC ARCHITECT ABOVE ABOVE FINISHED FLOOR BELOW BOTTOM CONDENSATE DRAIN CUBIC FEET PER MINUTE FOOT / FEET OPPOSED BLADE DAMPER NOT TO SCALE NECK TYPICAL DOOR UNDERCUT SCHEDULES 1.ALL ENVIRONMENTAL EXHAUST DUCTS SHALL BE OF SHEET METAL, TERMINATED 3 FT. AWAY FROM OPENINGS INTO THE BUILDING AND 3 FT. FROM PROPERTY LINE. 2.ALL CONDENSATE LINE SHALL BE ROUTED, SLOPED AND CONNECTED TO THE NEAREST LAVATORY TAILPIECE OR APPROVED PLUMBING RECEPTOR. 3.CONTRACTOR SHALL IINSTALL REQUIRED HVAC COMPONENTS TO FIT ACTUAL JOB CONDITIONS WITHOUT IMPAIRING THE DESIGN CONCEPT. 4.CONTRACTOR SHALL INCLUDE ANY DUCT TURNS OR ANY ADDITIONAL APPURTENANCES NECESSARY FOR THE PROPER FUNCTION OF THE SYSTEM EVEN THOUGH THEY ARE NOT SHOWN ON THE DRAWINGS. 5.ALL REFRIGERANT PIPING SHALL BE SIZED AND INSTALLED PER MANUFACTURER'S RECOMMENDATIONS. 6.ALL AIR FILTERS SHALL BE MINIMUM MERV-13 FILTERS. FILTER SIZES SHALL MATCH THE SIZES OF THE RETURN AIR GRILLES. 7.CONTRACTOR SHALL MAKE ALL NECESSARY OFFSETS AND TRANSITION IN ORDER TO ACCOMMODATE DUCTWORK AND PIPING THAT CROSS WITH ONE ANOTHER INSIDE THE SOFFIT AREA. 8.CONTRACTOR SHALL PROVIDE NECESSARY SUPPORT MEMBRANE AND ASSOCIATED COMPONENTS IN ORDER TO MINIMIZE THE SPACE BETWEEN THE TOP OF FAN COIL UNIT AND THE STRUCTURE ABOVE. 9.ALL DUCTWORK SHALL BE ROUTED AS TIGHT AS POSSIBLE TO THE STRUCTURE ABOVE. 10.ALL EQUIPMENT SUBJECT TO NOISE-PRODUCING VIBRATIONS SHALL BE MOUNTED ON VIBRATION ISOLATORS WITH FLEXIBLE CONNECTIONS TO RELATING EQUIPMENT. ALL EQUIPMENT SHALL BE LABELED IN ACCORDANCE WITH THE PLANS. 11.PROVIDE LABELS AT ALL THERMOSTATS INDICATING THE UNIT DESIGNATION (COORDINATE WITH LABELING AT UNITS). CHECK THERMOSTATS LABEL AND REPLACE IF NOT LEGIBLE. 12.CONTRACTOR SHALL ADJUST SUPPLY AIR GRILLES, REGISTERS AND DIFFUSERS TO ACHIEVE PROPER AIR QUANTITIES AND THROW DISTRIBUTION OF AIR IN SPACE. CONTROL DAMPERS SHALL BE WITH LOCKING QUADRANTS ON OUTSIDE AIR DUCTING. 13.DUCTWORK WITH EXTERNAL INSULATION SHALL HAVE LOCKING QUADRANTS WITH ELEVATED DIAL REGULATOR SPRING END BEARING OR EQUAL. 14.CONTRACTOR SHALL INSTALL REQUIRED HVAC COMPONENTS TO FIT ACTUAL JOBSITE CONDITIONS WITHOUT IMPAIRING THE CONCEPT OF THE DESIGN. 15.CONTRACTOR SHALL VERIFY IN THE FIELD THE LOCATION OF NEW UNITS AND EQUIPMENT FOR ACCESSIBILITY PER MANUFATURER'S RECOMMENDATIONS AND APPLICABLE CODES PRIOR TO PURCHASING AND INSTALLATION. 16.CONTRACTOR SHALL PROVIDE TRAVERSE READING AT ALL FAN SYSTEM SUPPLY, RETURN AND EXHAUST DUCTS. VERIFY AIR AMOUNT AND CHECK FOR DUCT LEAKS. LEAKS IN DUCTWORK SHALL NOT EXCEED SMACNA STANDARDS. CONTRACTOR TO PROVIDE ALL NECESSARY CORRECTIVE ACTION. CONTRACTOR SHALL CHANGE FAN RPM TO MEET FIELD PRESSURE CONDITIONS INCLUDING CHANGING OF SHEAVES AS REQUIRED. 17.CONTRACTOR SHALL SET AIR EQUIPMENT, DAMPERS, STATIC FITTINGS, FAN RPM FOR DELIVERING AIR QUANTITIES AT ACTUAL FIELD CONDITIONS ACCORDING TO DESIGN. 18.LISTED SMOKE DAMPERS AND FIRE DAMPERS ARE REQUIRED TO BE INSTALLED AT ALL DUCT PENETRATIONS THROUGH AREA SEPARATION, OCCUPANCY SEPARATION WALLS, FIRE RATED CEILING, AND FIRE RATED SHAFTS PER CMC 2019. DAMPERS SHALL BE LIKED TO FIRE ALARM SYSTEM WITH DEDICATED ELECTRICAL POWER. 19.PROVIDE ACOUSTICAL LINING ON EVERY MAIN DUCT 10' AWAY FROM THE AC UNIT. 20.DUCT SYSTEM SHALL BE SEALED TO A LEAKAGE RATE NOT TO EXCEED 6% OF THE NOMINAL AIR HANDLER AIRFLOW RATE AS CONFIRMED THROUGH FIELD VERIFICATION AND DIAGNOSTIC TESTING. 21.OUTDOOR AIR RATES SHALL BE BALANCED WITHIN 10% OF THE DESIGN OUTSIDE AIR RATE. 22.CONTRACTOR SHALL PROVIDE AIR BALANCING DAMPERS AT BRANCH TAKE-OFFS WETHER STATED IN THE PLANS OR NOT. 23.ALL MECHANICAL VENTILATION AND SPACE CONDITIONING SYSTEMS SHALL BE INSTALLED WITH DUCTWORK, DAMPERS, AND CONTROLS TO ALLOW OUTSIDE AIR RATES TO BE OPERATED AT THE LARGER OF (1) THE MINIMUM LEVELS SPECIFIED IN SECTION 120.1(b) OR (2) THE RATE REQUIRED FOR MAKE UP OF EXHAUST SYSTEMS THAT ARE REQUIRED FOR AN EXEMPT OR COVERED PROCESS FOR CONTROL OF ODORS, OR FOR THE REMOVAL OF CONTAMINANTS WITH IN THE SPACE. ALL VARIABLE AIR VOLUME SPACE-CONDITIONING SYSTEMS SHALL INCLUDE CONTROLS THAT MAINTAIN MEASURED OUTSIDE AIR VENTILATION RATES WITHIN 10 PERCENT OF THE REQUIRED OUTSIDE AIR VENTILATION RATE AT BOTH FULL AND REDUCED SUPPLY AIRFLOW CONDITIONS. SEC.120.1(e) RTU 1 RTU 2 Scale Date Drawn By Checked By Project Number 14 3 0 E E D I N G E R A V E , S A N T A A N A , C A 9 2 7 0 5 NOVUM A R C H I T E C T U R E, Inc www.novumarchitecture.com OFFICES: SOUTH BAY / ORANGE COUNTY 116 S CATALINA AVE. STE. 122, REDONDO BEACH, CA 90277 TEL: 310-383-1827 / 310-709-4476 N AS SHOWN TO M ' S J R DC TT 9-1-2023 tom's2023 Mr . S p i r o s P o l i t i s No.Description Date 1 PC Comments 08/08/2024 2 HlthDep.Corr.2 09/03/2024 KITCHEN EXHAUST FAN SCHEDULE MARK MFR & MODEL NUMBER LOCATION SERVICE CFM E.S.P. (IN. WG.) DISCH. FPM FAN RPM SONES ELECTRICAL DATA NET. WT. (LBS.) QTY.REMARKS V./ PH./ HZ.HP BHP FLA CAPTIVEAIRE USBI24DD-RM OR APPROVED EQUAL ROOF H-1, H-2 5,600 2.5 2122 1254 32.11 208/3/60 7.5 4.61 21.1 859 1 1 - 7 CAPTIVEAIRE USBI13DD-RM OR APPROVED EQUAL ROOF H-3 1,000 1.25 875 1425 11.0 208/1/60 1 0.3 6.9 215 1 1 - 7 REMARKS: 1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS. 2. PROVIDE WITH PREMIUM EFFICIENCY MOTORS AND DISCONNECT SWITCH BY ELECTRICAL CONTRACTOR. 3. PROVIDE WITH HOOD ON/OFF TOGGLE SWITCH. INTERLOCK WITH THE CONTROL PANEL. 4. FAN TO RUN CONTINUOUSLY DURING OPERATING HOURS. 5. KITCHEN EXHAUST FAN AND ACCESSORIES SHALL BE FURNISHED THRU CAPTIVEAIRE AND SHALL BE INSTALLED BY MECHANICAL CONTRACTOR. 6. PROVIDE WITH PREMIUM EFFICIENCY MOTORS AND DISCONNECT SWITCH BY ELECTRICAL CONTRACTOR. 7. REFER TO MECHANICAL HOOD DETAILS SHEET M-212 TO M-224. MAKE-UP AIR UNIT SCHEDULE MARK MFR & MODEL NUMBER LOC.SERVICE FAN EVAP. COOLER ELECTRICAL DATA SONES NET. WT. (LBS.) QTY.REMARKS CFM E.S.P. (IN. WG.) HP BHP RPM EAT DB (̊F) EAT WB (̊F) LAT DB (̊F) LAT WB (̊F) V./ PH./ HZ.FLA MCA MOCP CAPTIVEAIRE A2-20D OR APPROVED EQUAL ROOF KITCHEN EXHAUST 5940 0.50 10 5.72 1444 90.0 69.0 74.0 69.0 208/3/60 14.5 33.8 60 24.1 970 1 1 - 9 REMARKS: 1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS. 2. INTERLOCK TO OPERATE WHEN KEF-1 AND KEF-2 IS ACTIVATED. 3. PROVIDE CIRCULATING PUMP, 3/4" MAKE UP WATER CONNECTION, 2/4" RAIN LINE. 4. PROVIDE EVAPORATOR COOLING WITH COOLING SENSOR AND HI-PRO POLYESER COATING FOR OUTSIDE EQUIPMENT INSTALLATION. 5. PROVIDE WITH NEOPRENE BLOWER VIBRATION ISOLATION, ROOF CURB AND RAIL. 6. PROVIDE WITH PREMIUM EFFICIENCY MOTORS AND DISCONNECT SWITCH BY ELECTRICAL CONTRACTOR. 7. PROVIDE WITH TOGGLE ON/OFF SWITCH. INTERLOCK TO CONTROL PANEL. 8. PROVIDE WITH SMOKE DETECTORS AT THE SUPPLY SIDE TO CONNECT TO THE BUILDING FORE PROTECTION SYSTEM (IF APPLICABLE), AND SHUTDOWN AC WHEN ACTIVATED. 9. REFER TO MECHANICAL HOOD DETAILS SHEET M-212 TO M-224. KEF 1 KEF 2 MAU 1 KITCHEN EXHAUST HOOD SCHEDULE MARK MFR & MODEL NUMBER SERVICE EXHAUST CFM VELOCITY (FPM) EXHAUST DUCT SIZE EXHAUST S.P. (IN. WG.) DIMENSIONS REMARKS LENGTH WIDTH HEIGHT CAPTIVEAIRE 5424-ND-2 OR APPROVED EQUAL AS SHOWN 3,575 2,023 18" DIA.-1.328 13'-0"54"24"1 - 2 CAPTIVEAIRE 5424-ND-2 OR APPROVED EQUAL AS SHOWN 2,025 1,146 18" DIA.-0.504 9'-0"54"24"1 - 2 CAPTIVEAIRE 5424-ND-2 OR APPROVED EQUAL AS SHOWN 1,000 1,273 12" DIA.-0.498 4'-6"54"24"1 - 2 REMARKS: 1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS. 2. REFER TO MECHANICAL HOOD DETAILS SHEET M-212 TO M-224. H 1 H 2 H 3 AIR BALANCE SCHEDULE MARK OUTSIDE AIR (CFM)EXHAUST AIR (CFM)DIFFERENCE (CFM) RTU-1 780 +780 RTU-2 200 +200 EF-1 50 -50 EF-2 100 -100 EF-3 50 -50 EF-4 50 -50 KEF-1 5600 -5600 KEF-2 1000 -1000 MAU-1 5940 +5310 TOTAL 6920 6850 +70 GENERAL NOTES SYMBOLS & SCHEDULE M-201 LEGEND AND ABBREVIATIONS IDENTIFICATION SYMBOLS 1 1 1 1430 E Edinger Ave 3/27/2025