Laserfiche WebLink
<br />LDViJJ <br /> <br />laV,lnc. <br />/80 Industrial Drive <br />Burlington, WI 53 J 05 <br />800_558.5986 <br />Fax 262.763.0156 <br />www.ldvuso.com <br /> <br />Section <br /> <br />5.00 <br />5.01 <br /> <br />6.00 <br />6.01 <br /> <br />6.02' <br /> <br />6.03 <br />6.04 <br /> <br />6.05 <br />6.06 <br />6.07 <br />6.08 <br /> <br />Qty <br /> <br />! 7. The drive mechanism shall utilize an electric screw drive with bearing follower and machined <br />track for smooth operation. <br />8. Room shall be supported utilizing heavy-duty machined precision siides mounted off steel <br />bearing piates that are attached to the frame rails using grade 8 bolts. <br />9. Use of floor rollers to support slide out is not acceptable, floor rollers cause deformation of body <br />i floor structure. <br />10. Slide-out shall not have any ceiling mounted components. <br />11. Controls for the slide-out shall utilize PLC logic and shall operate with the touch of one button. <br />When the control button is pressed it shall automatically deflate the air seal, pause, vacuum out the <br />air seal, extend the slide-out to its fully open position, and re-inflate the air seal. An LCD display <br />shall be provided on the control pad and shall be capable of displaying status information on the <br />: slide-out operation to the user. <br />, 12. Slide-out shall be finished in such a fashion that will allow access to serviceable components <br />under the floor of the body. All serviceable components shall be protected from the elements. <br />PAINT AND GRAPHICS: <br />Body base color shall be Dupont Imron N0006-HH white (or equal) with two-tone nonmetallic paint <br />scheme, (lower color - to be determined). <br />DRIVER/PASSENGER CAB AREA: <br />,1. Cover upper area of cab doors with 36-oz. vinyl and lower area with padded 36-oz. vinyl (color - <br />to be determined). <br />2. 10" high 0.100" bright aluminum tread plate kick plate at bottom of doors. <br />3. Heavy-duty rubber grab handle on each door. <br />4. 3/4" plywood panels covered with Excalibur onyx carpet above driver and passenger doors. <br />5. Cab sub ceiling shall be 1/2" plywood, APA,NRB-108FHA-UM-66. <br />6. Cover sub ceiling with Veelok Oxford 17-oz. ribbed loop pile fabric (color - Light Grey). <br />7. Vehicle height sign on dash. <br />8. Cab floor shall be covered with 5/8" plywood and covered with flooring as specified in Walls, <br />Ceiling and Floor section. <br />9. Black ribbed rubber mat in driver and passenger toe plate area. Insulate walls in toe plate area <br />i and cover walls and engine box with black carpeted panels. <br />10. Vehicle shall have a Final Stage Vehicle Certification and Altered Vehicle Certification as <br />required by Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 567.5 and 567.7 <br />11. Payload sticker in cab area with vehicle axle load ratings and available axle payload as built <br />Work area on passenger side constructed of 3/4" plywood covered with black laminate and trimmed <br />with vinyl T-molding. <br />Black laminate pull-out writing surface. _ <br />Control panels for 120Vac and 12Vdc systems shall be located in the overhead console. The entire <br />console shall be constructed of 3/4" plywood. The face shall be finished with black laminate and the <br />bottom shall be covered with Excalibur onyx carpet. <br />Blue/white dome light under overhead console. <br />Pair of 6" front windshield fans. <br />Safety Vision SV-CLCD,65-620 color back-up camera and monitor system <br /> <br />Pioneer DEH-P77DH (or current model) 45-watt x 4-channel, AM/FM/CD player and 3-band <br />parametric EO, with one (1) pair Pioneer TS-A6970R (or current model) 6" x 9" three-way speakers. <br /> <br />6 <br /> <br />1/28/2005 <br /> <br />Santa Ana Police Department (CA) MCC30LLC260-03.3 RZ.xls <br />