Laserfiche WebLink
<br />Attachment B <br /> <br />LDva LDV, Inc. <br />180 Industrial Drive <br />Burlington, WI 53105 <br />800.558.5986 <br />Fax 262.763.0156 <br />www.ldvusa.com <br />Section Qty <br /> 7. The drive mechanism shall utilize an electric screw drive with bearing follower and machined <br /> track for smooth operation. <br /> 8. Room shall be supported utilizing heavy-duty machined precision slides mounted off steel <br /> bearing plates that are attached to the frame rails using grade 8 bolts. <br /> 9. Use of floor rollers to support slide out is not acceptable, floor rollers cause deformation of body <br /> floor structure. <br /> 10. Slide-out shall not have any ceiling mounted components. <br /> 11. Controls for the slide-out shall utilize PLC logic and shall operate with the touch of one button. <br /> When the control button is pressed it shall automatically deflate the air seal, pause, vacuum out the <br /> air seal, extend the slide-out to its fully open position, and re-inflate the air seal. An LCD display <br /> shall be provided on the control pad and shall be capable of displaying status information on the <br /> slide-out operation to the user. <br /> 12. Slide-out shall be finished in such a fashion that will allow access to serviceable components <br /> under the floor of the body. All serviceable components shall be protected from the elements. <br />5.00 PAINT AND GRAPHICS: <br />5.01 Body base color shall be Dupont Imron N0006-HH white (or equal) with two-tone nonmetallic paint <br /> scheme, (lower color - to be determined). <br />6.00 DRIVER/PASSENGER CAB AREA: <br />6.01 1. Cover upper area of cab doors with 36-oz. vinyl and lower area with padded 36-oz. vinyl (color- <br /> to be determined). <br /> 2. 10" high 0.100" bright aluminum tread plate kick plate at bottom of doors. <br /> 3. Heavy-duty rubber grab handle on each door. <br /> 4. 3/4" plywood panels covered with vinyl above driver and passenger doors. <br /> 5. Cab sub ceiling shall be 1/2" plywood, APA-NRB-1 08FHA-UM-66. <br /> 6. Cover sub ceiling with Veelok Oxford 17-oz. ribbed loop pile fabric (color - Light Grey). <br /> 7. Vehicle height sign on dash. <br /> 8. Cab floor shall be covered with 5/8" plywood and covered with flooring as specified in Walls, <br /> Ceiling and Floor section. <br /> 9. Insulated black rubber mat in driver and passenger toe plate area. Insulate walls in toe plate area <br /> and cover walls and engine box with vinyl covered panels. <br /> 10. Vehicle shall have a Final Stage Vehicle Certification and Altered Vehicle Certification as <br /> required by Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 567.5 and 567.7 <br /> 11. Payload sticker in cab area with vehicle axle load ratings and available axle payload as built. <br />6.02 Work area on passenger side constructed of 3/4" plywood covered to match rear counter-tops and <br /> trimmed with vinyl T-molding. <br />6.03 Black laminate pull-out writing surface. <br />6.04 Control panels for 120Vac and 12Vdc systems shall be located in the overhead console. The entire <br /> console shall be constructed of 3/4" plywood. The face shall be finished with black laminate and the <br /> bottom shall be covered with vinyl. <br />6.05 1 Blue/white dome light under overhead console. <br />6.06 1 Pair of 6" front windshield fans. <br />6.07 1 Safetv Vision SV-CLCD-65-620 c%r back-uD camera and monitor system <br />6.08 1 Pioneer DEH-P4700MP (or current model) MOSFET 50-watt x 4, CD/MP3IWMAlWAV Receiver <br /> with 3-band parametric EO, and one (1) pair of Pioneer TS-A6970R (or current model) 6" x 9" three- <br /> way speakers. <br /> <br />Copy of Huntington Beach Police Department (CA) MCC30LLC260-0:62 MS.xls <br /> <br />6/16/2005 <br />