|
SEE POWER SYSTEMS STUDY SPECIFICATION FOR ADDITIONAL REQUIREMENTS. ALL REQUIRED POWER SYSTEMS
<br />STUDIES MUST BE COMPLETED AND SUBMITTED WITH ELECTRICAL POWER DISTRIBUTION EQUIPMENT SUBMITTAL.
<br />FAILURE TO DO SO WILL PREVENT THE ENGINEER FROM EFFECTIVELY EVALUATING THE SUBMITTAL AND SHALL RESULT
<br />IN REJECTION OF THE ELECTRICAL POWER DISTRIBUTION EQUIPMENT SUBMITTAL AS INCOMPLETE.
<br />CONTRACTOR SHALL SUBMIT SHOP DRAWINGS PER THE SPECIFICATIONS FOR SWITCHBOARDS, DISTRIBUTION BOARDS,
<br />TRANSFORMERS, PANEL BOARDS, AND ALL OTHER DEVICES SHOWN ON THE SINGLE LINE, PRIOR TO FABRICATION.
<br />CONTRACTOR SHALL SUBMIT SWITCHBOARD SHOP DRAWINGS TO THE SERVING UTILITY FOR APPROVAL PRIOR TO
<br />FABRICATION. CONTRACTOR SHALL SECURE CONFIRMATION THAT THE PROPOSED SWITCHBOARD COMPLIES WITH
<br />ELECTRIC UTILITY COMPANY REGULATIONS.
<br />LUGS SUITABLE FOR USE WITH COPPER OR ALUMINUM CONDUCTORS LISTED FOR USE WITH 75 DEGREE CELSIUS
<br />AMPACITY CONDUCTORS.
<br />TIN-PLATED ALUMINUM BUSSING WITH RECTANGULAR CROSS SECTION. HORIZONTAL AND VERTICAL BUSSING SHALL
<br />BE FULL LENGTH AND SHALL HAVE PROVISIONS FOR FUTURE EXTENSIONS. ALL BUSSING SHALL HAVE MINIMUM
<br />WITHSTAND RATING EQUAL TO THE AVAILABLE FAULT CURRENT INDICATED. ALL VERTICAL AND HORIZONTAL
<br />BUSSING SHALL BE RATED AT FULL CAPACITY IN ALL SWITCHBOARD AND DISTRIBUTION BOARD SECTIONS. PROVIDE
<br />100% NEUTRAL BUSSING MINIMUM UNLESS OTHERWISE NOTED. PROVIDE FULL LENGTH GROUND BUS AND, WHERE
<br />INDICATED ON PLANS, ISOLATED GROUND BUSSING. PROVIDE REAR WIRE WAY IN ALL SWITCHBOARD SECTIONS.
<br />ALL TERMINATIONS AND ENCLOSURES SHALL BE RATED FOR USE WITH 75 DEGREE CELSIUS CONDUCTORS.
<br />SERIES RATED DEVICES SHALL HAVE BEEN INVESTIGATED BY U.L. IN COMBINATION WITH THE END USE EQUIPMENT AND
<br />IN THE EQUIPMENT IN WHICH THESE DEVICES ARE USED AND SHALL BE MARKED WITH A SERIES RATING. ALL EQUIPMENT
<br />SHALL BE MARKED IN ACCORDANCE WITH NEC (OR CEC-WHERE ADOPTED) REQUIREMENTS. SEE SPECIFICATIONS FOR
<br />MORE INFORMATION. WHERE SERIES RATINGS ARE ALLOWED, THE EQUIPMENT SHALL BE LEGIBLY MARKED IN THE FIELD
<br />TO INDICATE A SERIES COMBINATION RATING WHICH SHALL BE READILY VISIBLE.
<br />ALL OVERCURRENT DEVICES IN AN INDIVIDUAL PIECE OF EQUIPMENT SHALL HAVE AN AIC RATING EQUAL TO THE
<br />OVERALL RATING OF THE EQUIPMENT. SERIES-RATING OF DEVICES WITHIN A PIECE OF EQUIPMENT IS NOT ALLOWED.
<br />SEE SPECIFICATIONS FOR MORE INFORMATION.
<br />ALL ITEMS DEPICTED ON THE SINGLE LINE DRAWINGS SHALL BE ASSUMED AS NEW U.O.N.
<br />ALL SWITCHGEAR SHALL BE SQUARE D OR EQUAL BY CUTLER-HAMMER, G.E., SIEMENS, IEM, OR Z-POWER AND
<br />DISTRIBUTION.
<br />PROVIDE GROUNDING PER NEC, OR CEC WHERE ADOPTED, 250.30. SEE TRANSFORMER SCHEDULE FOR GEC/BJ
<br />SIZING INFORMATION. SEE SEPARATELY DERIVED SYSTEM GROUNDING DETAIL A, SHEET E2-2, FOR MORE
<br />INFORMATION.
<br />b.
<br />ALL SWITCHBOARDS AND DISTRIBUTION BOARDS SHALL HAVE:9.
<br />6.
<br />1.
<br />2.
<br />3.
<br />5.
<br />7.
<br />a.
<br />GENERAL SINGLE LINE DIAGRAM NOTES:
<br />10.
<br />SPECIFIC SINGLE LINE NOTES:
<br />ALLOWABLE DIMENSIONS IN MAIN ELECTRICAL ROOM ARE A CRITICAL COORDINATION ITEM. CONTRACTOR SHALL
<br />PROVIDE 1/4"= 1'-0" SCALE DRAWINGS WITH SWITCHGEAR SUBMITTALS SHOWING THAT ALL PROPOSED EQUIPMENT WILL
<br />FIT IN THE SPACE PROVIDED. SUBMITTALS WITHOUT THIS DRAWING SHALL BE REJECTED AS INCOMPLETE.
<br />PROVIDE NEW OVERCURRENT PROTECTIVE DEVICE(S) COMPATIBLE WITH EXISTING ELECTRICAL DISTRIBUTION
<br />EQUIPMENT. AIC AND WITHSTAND RATINGS MATCHING EXISTING OCPD RATINGS OR DISTRIBUTION EQUIPMENT
<br />WITHSTAND RATINGS - WHICHEVER IS HIGHER.
<br />UNLESS SPECIFICALLY SHOWN AS (E), (R), (ER), (D), EXISTING OR NON-BOLD, ALL ELECTRICAL DEVICES SHOWN ARE NEW.
<br />WHERE REQUIRED BY THE LOCAL AUTHORITY HAVING JURISDICTION OR WHERE A NEW GROUND FAULT PROTECTIVE
<br />DEVICE IS BEING INSTALLED, A GROUND FAULT SYSTEM TEST SHALL BE CONDUCTED BY AN INDEPENDENT TESTING
<br />AGENCY PER NEC (OR CEC-WHERE ADOPTED) 230.95(C). THE GROUND FAULT SYSTEM TEST SHALL BE PERFORMED IN
<br />THE PRESENCE OF THE LOCAL AUTHORITY HAVING JURISDICTION. VERIFICATION OF DEVICE SETTINGS PER THE POWER
<br />SYSTEMS STUDY SPECIFICATION SHALL BE PERFORMED BY THE SAME INDEPENDENT TESTING AGENCY. THE GROUND
<br />FAULT TEST RESULTS SHALL BE DELIVERED TO THE ENGINEER OF RECORD. DURING THE CONSTRUCTION PHASE OF THE
<br />PROJECT, ALL NEW GROUND FAULT RELAYS SHALL BE SET AT THE LOWEST AVAILABLE TIME DELAY AND PICK-UP
<br />SETTINGS.
<br />1
<br />2
<br />c.PERMANENT PLACARD(S) MARKED PER THE SPECIFICATIONS AND PER NEC (OR CEC-WHERE ADOPTED) SECTIONS
<br />225.37, 230.2(E), 690.56, 692.56, 700.7, 701.7, 702.7, AND 705.10 AND IFC (OR CFC - WHERE ADOPTED) SECTION 608.2.6.1.
<br />DENOTING THE PRESENCE OF ADDITIONAL SERVICES, PHOTOVOLTAIC SYSTEMS, FUEL CELLS, EMERGENCY,
<br />STATIONARY BATTERY STORAGE SYSTEMS, OR STAND-BY POWER SOURCES AS APPLICABLE.
<br />ALL SERVICE ENTRANCE EQUIPMENT RATED AT 400A OR GREATER SHALL BE PROVIDED WITH A BACKFEED-RATED, SOLID
<br />STATE MAIN OVERCURRENT DEVICE AND BUSSING RATED AT 100% OPERATION (1000A/sq.in. FOR CU, 750A/sq.in. FOR AL).
<br />NO HEAT RISE RATED BUSSING ALLOWED. NON-SERVICE ENTRANCE SWITCHBOARDS AND DISTRIBUTION BOARDS
<br />LARGER THAN 600A SHALL BE PROVIDED WITH BUSSING RATED FOR 100% OPERATION - SEE SPECIFICATION FOR CIRCUIT
<br />BREAKER REQUIREMENTS. ALL NON-SERVICE ENTRANCE SWITCHBOARDS AND DISTRIBUTION BOARD MAIN
<br />OVERCURRENT DEVICES SHALL BE BACKFEED-RATED. BACKFEED RATINGS SHALL COMPLY WITH NEC, OR CEC WHERE
<br />ADOPTED, 710.15 (E) AND 705.12(B)(4). SEE SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS REGARDING CIRCUIT
<br />BREAKERS.
<br />8.PROVIDE CIRCUIT BREAKER ARC ENERGY REDUCTION MAINTENANCE SWITCHING PER NEC, OR CEC WHERE ADPOPTED,
<br />240.87(B)(3) FOR ANY CIRCUIT BREAKER, 1200A FRAME AND LARGER. SEE SPECIFICATIONS FOR ADDITIONAL
<br />REQUIREMENTS.
<br />4.ALL SWITCHBOARDS, SWITCHGEAR, AND PANELBOARDS SHALL HAVE A SHORT-CIRCUIT CURRENT RATING NOT LESS
<br />THAN THE AVAILABLE FAULT CURRENT. THE AVAILABLE FAULT CURRENT AND THE DATE THE CALCULATION WAS
<br />PERFORMED SHALL BE FIELD MARKED ON THE ENCLOSURE AT THE POINT OF SUPPLY.
<br />11.
<br />12.
<br />13.
<br />14.
<br />15.
<br />U.G.P.S.
<br />3,000A
<br />3P
<br />EX
<br />110A
<br />3P
<br />PARTIAL EXISTING SERVICE ENTRANCE EQUIPMENT "MSB3"
<br />3,000A, (100% RATED) 277/480V- 3~ - 4W
<br />AVAILABLE FAULT CURRENT PER SCE = 40,000A
<br />CONNECTED LOAD =
<br />GROUNDING
<br />EXISTING
<br />B
<br />E-2.2
<br />1
<br />TD
<br />1
<br />TD1
<br />2
<br />DP1
<br />DP
<br />1
<br />NOTESV.D.LOADFEEDERCONDUIT AND CONDUCTORS (%)
<br />AVAIL.FAULT
<br />CURRENT (A)(A)
<br />DISTANCE
<br />(FT)
<br />SCALE: NONE
<br />CB
<br />D
<br />1
<br />---2"C., 3#1 + 1#6 GRD.CBD1
<br />W.P.
<br />W.P.
<br />ENCLOSED CIRCUIT BREAKER
<br />"CBD1"
<br />600V, 110A-3P
<br />NEMA 3R
<br />75KVA
<br />---2"C., 3#1 + 1#6 GRD.TD1
<br />---3"C., 4#4/0 + 1#4 GRD.DP1
<br />AVAILABLE FAULT CURRENT VALUE AT THE END OF THE FEEDER INDICATED. CALCULATIONS ARE BASED UPON INITIAL
<br />VALUES RECEIVED FROM THE SERVING UTILITY AND THE LENGTH AND IMPEDANCE OF THE FEEDER. THE SHORT
<br />CIRCUIT CURRENT RATING, EQUIPMENT BUS BRACING, AND/OR AMP INTERRUPTING CURRENT OF EQUIPMENT
<br />CONNECTED ON THE LOAD SIDE OF THE FEEDER SHALL BE GREATER THAN THE AVAILABLE FAULT CURRENT.
<br />VOLTAGE DROP VALUE INDICATED IS AT THE END OF THE FEEDER.
<br />DISTANCE SHOWN IS FOR DESIGN PURPOSES ONLY. IT IS NOT A MATERIAL TAKEOFF.
<br />LOADS INDICATED WITH " ( ) " REPRESENT WORST CASE LOAD IN AMPS.
<br />ALL FEEDERS SHOWN, UNLESS SPECIFICALLY NOTED OTHERWISE, ARE PRESUMED TO BE ROUTED IN METAL
<br />RACEWAYS. IF P.V.C. CONDUITS ARE UTILIZED, THE CONTRACTOR SHALL PROVIDE AN EQUIPMENT GROUND PER NEC,
<br />OR CEC WHERE ADOPTED, TABLE 250.122 OR, WHERE REQUIRED, PROVIDE A MAIN BONDING JUMPER PER TABLE
<br />250.66 AND INCREASE THE CONDUIT SIZE ACCORDINGLY.
<br />5.
<br />4.
<br />3.
<br />2.
<br />1.
<br />GENERAL FEEDER SCHEDULE NOTES:
<br />PANELS SHALL BE OF THE DEAD FRONT SAFETY TYPE. PANELS SHALL BE
<br />MINIMUM 20" WIDE AND 5-3/4" DEEP UNLESS OTHERWISE NOTED ON PLAN.
<br />COORDINATE WITH APPLICABLE TRADE TO INSURE RECESSED MOUNTED
<br />PANELBOARDS WILL SEAT FLUSH IN THE WALLS PROVIDED. PANEL TRIMS
<br />SHALL HAVE CONCEALED DOORS AND FASTENERS WITH FLUSH TYPE
<br />COMBINATION LOCK AND CATCH, TWO MILLED TYPE KEYS SUPPLIED WITH
<br />EACH PANEL. ALL LOCKS SHALL BE KEYED ALIKE AND EACH DOOR SHALL
<br />HAVE A PLASTIC COVERED DIRECTORY FRAME WITH A TYPED IDENTIFICATION
<br />CARD OF ALL CIRCUIT AND PANEL NUMBERS FOR BRANCH CIRCUIT
<br />PANELBOARDS.
<br />ALL CIRCUIT BREAKERS SHALL BE BOLT-ON TYPE AND SHALL BE SUITABLE
<br />FOR 75 DEGREE AMPACITY CONDUCTORS.
<br />PROVIDE BREAKER INTERLOCK WITH ADJACENT BREAKER(S) FOR ANY
<br />MULTI-WIRE BRANCH CIRCUIT. BREAKER INTERLOCK GROUPING SHALL BE
<br />BY BRANCH CIRCUIT GROUP (i.e. MULTIPLE CIRCUITS SHARING A COMMON
<br />NEUTRAL (NEC, OR CEC WHERE ADOPTED, 210.4(B),) COMMON YOKE (NEC,
<br />OR CEC WHERE ADOPTED, 210.7), OR FURNITURE SYSTEM NEC OR CEC
<br />WHERE ADOPTED, 605.5 AND 605.7). WHERE AN EXISTING PANEL IS BEING
<br />ALTERED OR MODIFIED IN ANY WAY, CONTRACTOR SHALL INCLUDE ALL
<br />COSTS IN BASE BID TO ADD BREAKER INTERLOCKS TO EXISTING
<br />MULTI-WIRE BRANCH CIRCUITS BASED ON CONTRACTOR'S INVESTIGATION
<br />OF EXISTING CONDITIONS.
<br />ALL CIRCUIT BREAKERS USED AS SWITCHES SHALL BE UL LISTED AND
<br />LABELED "SWD" FOR SWITCHING DUTY.
<br />ALL BUSSING SHALL BE TIN PLATED ALUMINUM.
<br />WHERE PANEL IS INDICATED AS RECESSED OR FLUSH MOUNTED, PROVIDE
<br />SPARE CONDUITS STUBBED UP INTO THE ACCESSIBLE CEILING SPACE.
<br />PROVIDE ONE (1) 3/4" CONDUIT ONLY FOR EACH THREE (3) SPARES OR
<br />SPACES, MINIMUM OF TWO (2). EACH CONDUIT SHALL BE TAGGED, CAPPED
<br />AND MARKED FOR FUTURE USE.
<br />WHERE PANEL CIRCUIT BREAKER RATING IS SHOWN AS SERIES RATED,
<br />PROVIDE CIRCUIT BREAKERS IN PANELBOARD WHICH ARE SERIES RATED
<br />WITH THE UPSTREAM SYSTEM FOR THE AVAILABLE FAULT CURRENT. THE
<br />PANELBOARD SHALL BE MARKED WITH THE SERIES CONNECTED RATINGS,
<br />AS WELL AS ALL MARKING AS REQUIRED BY THE NEC, OR CEC WHERE
<br />ADOPTED, 240.86(B).
<br />WHERE PANEL IS INDICATED TO INCLUDE AN I/G BUS, PROVIDE
<br />PANELBOARDS WITH AN ISOLATED GROUND BUS, DRILLED AND TAPPED
<br />FOR NUMBER OF ISOLATED GROUND CONDUCTORS SHOWN, AS WELL AS
<br />FOR ALL SPARES AND SPACES SHOWN ON THE PANELBOARD.
<br />WHERE PANEL IS INDICATED TO INCLUDE 200% NEUTRAL, PROVIDE
<br />PANELBOARDS UL LISTED AS HAVING NEUTRAL BUSSES RATED TO CARRY
<br />200 PERCENT OF THE CURRENT CARRYING CAPACITY OF THE PHASE
<br />BUSSING. OTHERWISE, NEUTRAL BUSSING TO BE FULL SIZE AND
<br />RECTANGULAR.
<br />WHERE PANEL IS INDICATED TO INCLUDE DOUBLE LUGS, PROVIDE A
<br />DOUBLE LUG KIT AT THE SAME END OF THE PANELBOARD AS THE
<br />PANELBOARD MAIN LUGS.
<br />WHERE PANEL IS INDICATED TO INCLUDE FEED THRU LUGS, PROVIDE FEED
<br />THROUGH LUGS AT THE OPPOSITE END OF THE PANELBOARD FROM THE
<br />PANELBOARD MAIN LUGS.
<br />GENERAL PANEL SCHEDULE NOTES:
<br />13.
<br />12.
<br />11.
<br />9.
<br />8.
<br />6.
<br />7.
<br />5.
<br />4.
<br />3.
<br />2.
<br />1.
<br />UPON PROJECT COMPLETION, CONTRACTOR SHALL INSTALL TYPED AS-BUILT
<br />PANEL DIRECTORIES IN EACH PANEL WITHIN THE MFGR-PROVIDED DIRECTORY
<br />HOLDER. THE DIRECTORY SHALL CLEARLY IDENTIFY EACH CIRCUIT TO ITS
<br />CLEAR, EVIDENT, AND SPECIFIC PURPOSE OR USE. EACH CIRCUIT IDENTITY
<br />SHALL INCLUDE SUFFICIENT DETAIL TO ALLOW EACH CIRCUIT TO BE
<br />DISTINGUISHED FROM ALL OTHERS PER NEC, OR CEC WHERE ADOPTED, ART
<br />408.1 AND 408.4. HANDWRITTEN DIRECTORIES ARE UNACCEPTABLE. COPIES
<br />OF AS-BUILT PANEL SCHEDULES SHALL BE PLACED IN PANEL DIRECTORIES.
<br />E.C. TO INCLUDE ALL COSTS REQUIRED FOR LARGER-THAN-STANDARD
<br />CUSTOM PANEL DIRECTORY HOLDERS TO ACCOMMODATE COPIES OF
<br />AS-BUILT PANEL SCHEDULES.
<br />PANELBOARDS SHALL BE MANUFACTURED BY G.E., CUTLER-HAMMER,
<br />SIEMENS, OR SQUARE "D". FUSED PANEL BOARDS SHALL BE BY COOPER
<br />BUSSMANN.
<br />SPECIFIC PANEL SCHEDULE NOTES:
<br />"E"
<br />"D"
<br />"C"
<br />"B"
<br />"A"
<br />15.
<br />14.
<br />16.PROVIDE SHOP DRAWING SUBMITTAL PER THE ELECTRICAL SPECIFICATION
<br />SUBMITTAL REQUIREMENTS FOR EACH PANEL DEPICTING CONFORMANCE
<br />WITH THE ABOVE NOTES AND SCHEDULES.
<br />PROVIDE LOCK-ON DEVICE.
<br />PROVIDE PERMANENT LOCK-OFF DEVICE THAT SHALL REMAIN IN PLACE
<br />WITH OR WITHOUT THE LOCK INSTALLED, PER NEC, OR CEC WHERE
<br />ADOPTED, SECTION 110.25.
<br />PROVIDE SHUNT TRIP DEVICE.
<br />PROVIDE GFCI TYPE DEVICE.
<br />PROVIDE A RED CIRCUIT BREAKER.
<br />PROVIDE BREAKER LOCK OFF DEVICE ON ANY CIRCUIT BREAKER FEEDING
<br />A TRANSFORMER AS REQUIRED, PER NEC, OR CEC WHERE ADOPTED,
<br />450.14. WHERE AN EXISTING PANEL IS BEING ALTERED OR MODIFIED IN
<br />ANY WAY, CONTRACTOR SHALL INCLUDE ALL COSTS IN BASE BID TO ADD
<br />BREAKER LOCK-OFF DEVICES TO EXISTING TRANSFORMER CIRCUIT
<br />BREAKERS BASED ON CONTRACTOR'S INVESTIGATION OF EXISTING
<br />CONDITIONS.
<br />10.
<br />tk1sc project number: B2305501.000
<br />drawn by:checked by:
<br />drawing no.:
<br />ar
<br />c
<br />h
<br />i
<br />t
<br />e
<br />c
<br />t
<br />u
<br />r
<br />e
<br />pl
<br />a
<br />n
<br />n
<br />i
<br />n
<br />g
<br />in
<br />t
<br />e
<br />r
<br />i
<br />o
<br />r
<br />s
<br />tB
<br />P
<br />/
<br />A
<br />r
<br />c
<br />h
<br />i
<br />t
<br />e
<br />c
<br />t
<br />u
<br />r
<br />e
<br />46
<br />1
<br />1
<br />
<br />T
<br />e
<br />l
<br />l
<br />e
<br />r
<br />
<br />A
<br />v
<br />e
<br />n
<br />u
<br />e
<br />Ne
<br />w
<br />p
<br />o
<br />r
<br />t
<br />
<br />B
<br />e
<br />a
<br />c
<br />h
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />6
<br />6
<br />0
<br />ph
<br />:
<br />
<br />9
<br />4
<br />9
<br />.
<br />6
<br />7
<br />3
<br />.
<br />0
<br />3
<br />0
<br />0
<br />consultant
<br />agency
<br />owner
<br />date:
<br />drawing title:
<br />description:date:Rev:
<br />tBP project number :
<br />architect
<br />THIS DRAWING AND THE DESIGNS, DEPICTIONS, IDEAS AND OTHER INFORMATION
<br />CONTAINED HEREIN CONSTITUTE UNPUBLISHED WORK OF tBP/ARCHITECTURE AND
<br />SHALL REMAIN THE PROPERTY OF tBP/ARCHITECTURE IN PERPETUITY. NO PART
<br />THEREOF SHALL BE REPRODUCED, DISCLOSED, DISTRIBUTED, SOLD, PUBLISHED OR
<br />OTHERWISE USED IN ANY WAY WITHOUT THE ADVANCED EXPRESS WRITTEN CONSENT
<br />OF tBP/ARCHITECTURE.
<br />ph: 714.667.2700
<br />SANTA ANA, CA 92701
<br />20 CIVIC CENTER PLAZA
<br />SANTA ANA PLANNING AND BUILDING AGENCY
<br />#
<br />DA
<br />N
<br />C
<br />E
<br />
<br />S
<br />T
<br />U
<br />D
<br />I
<br />O
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />L
<br />I
<br />F
<br />O
<br />R
<br />N
<br />I
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />7
<br />12
<br />0
<br />2
<br />
<br />W
<br />
<br />E
<br />D
<br />I
<br />N
<br />G
<br />E
<br />R
<br />
<br />A
<br />V
<br />E
<br />MA
<br />T
<br />E
<br />R
<br />
<br />D
<br />E
<br />I
<br />
<br />H
<br />I
<br />G
<br />H
<br />
<br />S
<br />C
<br />H
<br />O
<br />O
<br />L
<br />21125.00
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />L
<br />I
<br />F
<br />O
<br />R
<br />N
<br />I
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />7
<br />12
<br />0
<br />2
<br />
<br />W
<br />
<br />E
<br />D
<br />I
<br />N
<br />G
<br />E
<br />R
<br />
<br />A
<br />V
<br />E
<br />MA
<br />T
<br />E
<br />R
<br />
<br />D
<br />E
<br />I
<br />
<br />H
<br />I
<br />G
<br />H
<br />
<br />S
<br />C
<br />H
<br />O
<br />O
<br />L
<br />21125.00
<br />09/06/2023
<br />11870 Pierce Street, Suite 160
<br />Riverside, California 92505
<br />951.299.4160 www.tk1sc.com
<br />Project Leader - Bill Voller
<br />tk1sc Job #: B2305501.000
<br />Electrical Lead - Marie Rothenberger
<br />City Submittal 09/06/23-
<br />SINGLE LINE DIAGRAM
<br />E2-1
<br />21159.00
<br />1202 W Edinger
<br />Ave10/3/2024
|