|
97 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
<br />6. These products are suitable for factory wiring only.
<br />7. In Canada Models CEN-60-48, CEN-60-54, CEN-75-48 and CEN-75-54 must have their Class 2 output circuit and components
<br />completely inaccessible in the end product application.
<br />LED array drivers, Models LPV-60-12, LPV-60-15, LPV-60-24, LPV-60-36 and LPV-60-48.
<br />1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2
<br />output.
<br />2. These products are provided with the following electrical ratings:
<br />Input Output
<br />Model Vac A Hz Vdc A
<br />|LPV-60-12 100-240 1.2 50/60 12 5.0
<br />|LPV-60-15 100-240 1.2 50/60 15 4.0
<br />LPV-60-24 100-240 1.2 50/60 24 2.5
<br />ILPV-60-36 100-240 1.2 50/60 36 1.67
<br />|LPV-60-48 100-240 1.2 50/60 48 1.25
<br />3. The Class 2 output of these power supplies are suitable for use in dry and damp locations only.
<br />4. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />5. These products shall be enclosed in the end product.
<br />6. These products are suitable for factory wiring only.
<br />7. Model LPV-60-48 is only acceptable for use with the product in the US.
<br />8. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and
<br />wet locations.
<br />MEGAPULL INC
<br />161 TROLLINGWOOD LANE
<br />E318039
<br />MORRISVILLE, NC 28117
<br />Class 2 LED Module, Cat. No. AABBCCEEFFG MMDDYY series, where AA may be FL, DL or REI where BB may be CX, LK, LR,
<br />LC, NI, AV, OS, AO, AB, CR, LU, SE, or OT, where CC may be BL, RE, GR WH, CW, NW, VWV, CY, RB, RO, AM or OT, where
<br />EE may be WB, or NB, where FF may be SP or DP, where G may be any number from 0 to 9, where MMDDYY may be may be
<br />any number combinations from 000000 to 999999.
<br />1. For connection to the Class 2 output of a Listed or Recognized Component power source rated 15 Vac or 36Vdc maximum.
<br />Other applications require additional evaluation.
<br />2. Class 2 LED Modules, Cat. No. No. AA01 BBCCEEFFG MMDDYY series are each rated max. 5 Watts per unit. When units are
<br />connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2
<br />supply.
<br />3. These products are suitable for use in dry, damp and wet locations when rated 15 Vac or 30Vdc maximum. Products that are
<br />rated maximum of 36 VDC are suitable for dry and damp locations only.
<br />4. These products are not required to be enclosed or protected from the weather in the end product.
<br />5. These products may be secured in place in the end product by any means available.
<br />6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall
<br />be considered.
<br />MIC ELECTRONICS LTD
<br />A-4, ELECTRONIC COMPLEX
<br />KUSHAIGUDA,
<br />E351950
<br />HYDERABAD, AP 500062 INDIA
<br />Dry location, Indoor LED Display Module signs, Models DigiTile-9RC, DigiTile-12RC.
<br />1. Acceptability for multiple connections (daisy chaining) not exceeding 12 A (based on 14AWG power supply cord) on a single
<br />branch circuit shall be determined by the end product requirements.
<br />2. These products were tested for use at a room ambient temperature of 25°C. Testing was conducted on the test bench
<br />positioned vertically facing horizontally. The need for conducting temperature testing in the end product shall be considered
<br />where the units are installed in a higher ambient.
<br />3. The suitability of the mounting means shall be determined in the end use.
<br />4. The Leakage current test shall be conducted in the end use for cord connected signs.
<br />5. No supply disconnecting means was provided. The need for a separate disconnect in the end product shall be considered.
<br />6. The sign components are for dry location use.
<br />7. The suitability of Power Supply Cord needs to be determined in the end use.
<br />8. This product was not tested for conformal coating ageing test. The coating shall be applied on R/C PWB for indoor application
<br />only. The need for conducting the test shall be determined in the end use based on spacing and pollution degree as per end
<br />product requirements.
<br />9. This product was tested for 5VA flame test on the front sign side.
<br />MICRALUX INC E235719
<br />1162 N REESE DR
<br />PROVO, UT 84601
<br />Class 2 LED Module, Cat. Nos. LED Strips
<br />1. These products are only suitable for connection to a UL Listed or Recognized Class 2,12 volt DC power source.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2
<br />voltage and energy limited supplies.
|