625 S Cypress Ave - Plan - Laserfiche WebLink

Home Browse Search

REFLECTED CEILING PLAN GENERAL NOTES 1. REFER TO ADDITIONAL NOTES ON SHEET T0.01. 2. CONTRACTOR SHALL VERIFY THAT (E) CONDITIONS ARE AS INDICATED ON THE DRAWINGS. NOTIFY THE ARCHITECT IMMEDIATELY OF VARIATIONS OR DISCREPANCIES. DO NOT PROCEED WITH AFFECTED WORK UNTIL THE VARIATIONS OR DISCREPANCIES ARE RESOLVED BY THE ARCHITECT. 3. PROTECT ALL EXISTING ITEMS THAT ARE TO REMAIN. RESTORE ALL SURROUNDING AREAS AFFECTED BY THE WORK. 4. ALL DIMENSIONS SHALL BE VERIFIED IN THE FIELD. DIMENSIONS ARE TO FACE OF FINISHED WALL, U.O.N. DIMENSIONS OF (E) CONDITIONS ARE FOR REFERENCE ONLY AND SHALL BE VERIFIED BY THE CONTRACTOR IN THE FIELD. WHERE NO DIMENSION IS PROVIDED CONSULT WITH THE ARCHITECT FOR CLARIFICATION BEFORE PROCEEDING WITH AFFECTED WORK. 5. CONTRACTOR SHALL VERIFY "CENTERLINE" AND "MATCHLINE" ALIGNMENTS OF ALL ARCHITECTURAL ELEMENTS. THE CONTRACTOR SHALL NOTIFY THE ARCHITECT OF ANY DISCREPANCIES BEFORE PROCEEDING. 6. PROVIDE CEILING ACCESS AS INDICATED AND/OR AS REQUIRED FOR EQUIPMENT MAINTENANCE. VERIFY MANUFACTURER RECOMMENDATIONS. 7. CONTRACTOR TO COORDINATE THE WORK OF ALL TRADES TO MAINTAIN SCHEDULED CEILING HEIGHTS AND REQUIRED CLEARANCES FOR FIXTURES, DUCTS, SUSPENSION SYSTEMS, PIPING, ETC. 8. CONTRACTOR TO COORDINATE FIXTURE LOCATIONS WITH ALL (E) AND NEW CEILING FRAMING. NOTIFY ARCHITECT OF ANY VARIATIONS OR DISCREPANCIES IN LOCATIONS SHOWN PRIOR TO PROCEEDING. PLAN LEGEND EXIT SIGNAGE AND EGRESS ILLUMINATION NOTES KEYNOTES 1. EXIT SIGNS SHALL BE INTERNALLY OR EXTERNALLY ILLUMINATED. EXIT SIGNS ILLUMINATED BY AN EXTERNAL SOURCE SHALL HAVE AN INTENSITY OF NOT LESS THAN 5 FOOT CANDLES (54 IUX). INTERNALLY ILLUMINATED SIGNS SHALL BE LISTED AND LABELED AND SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS AND CBC SECTION 2702. 2. EXIT SIGNS SHALL BE ILLUMINATED AT ALL TIMES. (CBC SECTION 1013.3) 3. EXIT SIGNS SHALL BE CONNECTED TO AN EMERGENCY POWER SYSTEM THAT WILL PROVIDE AN ILLUMINATION OF NOT LESS THAN 90 MINUTES IN CASE OF PRIMARY POWER LOSS. (CBC SECTION 1013.6.3) 4. THE MEANS OF EGRESS, INCLUDING THE EXIT DISCHARGE, SHALL BE ILLUMINATED AT ALL TIMES THE BUILDING SPACE SERVED BY THE MEANS OF EGRESS IS OCCUPIED. 5. THE MEANS OF EGRESS ILLUMINATION LEVEL SHALL NOT BE LESS THAN 1 FOOT-CANDLE AT THE WALKING SURFACE. 6. THE POWER SUPPLY FOR MEANS OF EGRESS ILLUMINATION SHALL NORMALLY BE PROVIDED BY THE PREMISES’ELECTRICAL SUPPLY. IN THE EVENT OF POWER SUPPLY FAILURE, AN EMERGENCY ELECTRICAL SYSTEM SHALL AUTOMATICALLY ILLUMINATE THE FOLLOWING AREAS: A. AISLES AND UNENCLOSED EGRESS STAIRWAYS IN ROOMS AND SPACES THAT REQUIRE TWO OR MORE MEANS OF EGRESS. B. CORRIDORS, EXIT ENCLOSURES AND EXIT PASSAGEWAYS IN BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. C. EXTERIOR EGRESS COMPONENTS AT OTHER THAN THE LEVEL OF EXIT DISCHARGE UNTIL EXIT DISCHARGE IS ACCOMPLISHED FOR BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. D. INTERIOR EXIT DISCHARGE ELEMENTS, AS PERMITTED IN CBC SECTION 1028.1, IN BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. E. EXTERIOR LANDINGS, AS REQUIRED BY CBC SECTION 1010.1.6, FOR EXIT DISCHARGE DOORWAYS IN BUILDINGS REQUIRED TO HAVE TWO OR MORE EXITS. 7. THE EMERGENCY POWER SYSTEM SHALL PROVIDE POWER FOR A DURATION OF NOT LESS THAN 90 MINUTES AND SHALL CONSIST OF STORAGE BATTERIES, UNIT EQUIPMENT OR AN ON-SITE GENERATOR. THE INSTALLATION OF THE EMERGENCY POWER SYSTEM SHALL BE IN ACCORDANCE WITH CBC SECTION 2702. 8. EMERGENCY LIGHTING FACILITIES SHALL BE ARRANGED TO PROVIDE INITIAL ILLUMINATION THAT IS AT LEAST AN AVERAGE OF 1 FOOT-CANDLE (11 LUX) AND A MINIMUM AT ANY POINT OF 0.1 FOOT-CANDLE (1 LUX) MEASURED ALONG THE PATH OF EGRESS AT FLOOR LEVEL. ILLUMINATION LEVELS SHALL BE PERMITTED TO DECLINE TO 0.6 FOOT-CANDLE (6 LUX)AVERAGE AND A MINIMUM AT ANY POINT OF 0.06 FOOT-CANDLE (0.6 LUX) AT THE END OF THE EMERGENCY LIGHTING TIME DURATION. A MAXIMUM-TO-MINIMUM ILLUMINATION UNIFORMITY RATIO OF 40 TO 1 SHALL NOT BE EXCEEDED. LIGHT FIXTURE SCHEDULE 2x WOOD STUDS @ 16" O.C., MATCH ADJACENT WALL ASSEMBLY EXISTING WOOD STUD WALL TO REMAIN -NEW GYP BD SHEATHING ON INTERIOR SIDE(S) OF ALL (E) WALLS, TYP. -ALL EXTERIOR WALLS TO RECEIVE R-19 BATT INSULATION ACT CEILING, REFER TO SHEAR WALL SHEATHING, REFER TO STRUCTURAL DRAWINGS 2 A5.04 GYP. BD. CEILING, REFER TO 1 A5.04 DESIGN-BUILD MECHANICAL CATWALK REQUIRED FOR ACCESS TO ALL FAN COIL UNITS FROM CEILING ACCESS POINT; FIELD VERIFY LOCATION WITH (E) TRUSSES AND NEW CEILING FRAMING SUPPLY AIR DIFFUSER, REFER TO MECHANICAL DRAWINGS RETURN AIR GRILLE, REFER TO MECHANICAL DRAWINGS TRANSFER AIR GRILLE, REFER TO MECHANICAL DRAWINGS EXHAUST AIR GRILLE / EXHAUST FAN, REFER TO MECHANICAL DRAWINGS WALL MOUNTED (EX1) OR CEILING SUSPENDED (EX2) ILLUMINATED EXIT SIGN. EXIT SIGNS SHALL BE ILLUMINATED AT ALL TIMES FOR A DURATION OF NOT LESS THAN 90 MINUTES IN CASE OF PRIMARY POWER LOSS. TO ENSURE THIS CONTINUOUS ILLUMINATION, THE EXIT SIGN MUST BE CONNECTED TO AN EMERGENCY POWER SYSTEM PROVIDED FROM STORAGE BATTERIES, UNIT EQUIPMENT OR AN ON-SITE GENERATOR, CBC 1013.6.3. REFER TO ELECTRICAL DRAWINGS 1 A3.00 1 A3.01 2 A3.01 MULTI-PURPOSE ROOM A 02 ENTRY / CHECK IN OFFICE 01 TRAINING ROOM B 03 HALLWAY 04 TRAINING ROOM C 05 HALLWAY 06 WOMENS 07 MENS 09 RESTROOM 11 JANITOR 12 OFFICE AND BREAKROOM 10 EQ EQ 2 A3.00 1 2 3 A B C D E F A.F.F. GYP. BD. 8' - 11" A.F.F. GYP. BD. 8' - 11" A.F.F. GYP. BD. 8' - 11" A.F.F. GYP. BD. 9' - 11" A.F.F. GYP. BD. 9' - 11" A.F.F. GYP. BD. 9' - 11"A.F.F. GYP. BD. 9' - 11" A.F.F. GYP. BD. 9' - 11" A.F.F. GYP. BD. 8' - 11" EQ EQ 2' - 0" EQ EQ EQ EQ EQ EQ EQ EQ 2' - 0" 2' - 0 " 2' - 0" 2' - 0 " F3 F1 F1 F1 F1 F1 F2 F2 F2 F3 F3 F4 F4 F5 F5 F12 F12 F12 F12 F12 F6 F6 F6 F6 F6 F3 F3 F3 F2 F8 F7 F9 F9 F9 F9 F9 F9 F9 F10 F10 F10F10F10F10F10 8" 15 ' - 8 " 25 ' - 0 " 1' - 3 " 42 ' - 7 " 72' - 5"18' - 10" 26 ' - 6 " 14 ' - 9 " 1"7' - 1"10' - 9"7' - 3"22' - 6"23' - 7"18' - 6"7" 17' - 11"72' - 5" F9 A.F.F. (E) PLASTER 12' - 8" A.F.F. GYP. BD. 8' - 11" NO CEILING EXPOSED STRUCTURE 12' -5" A.F.F. EQ EQ EQ EQ EQ EQ3' - 6 3/4"3' - 6" 06-03 06-03 NO CEILING EXPOSED STRUCTURE +7'-6" +8'-0" +8'-7" +8'-7" +8'-7" +8'-7" +10'-6" +11'-5" +10'-6" +10'-6" +10'-6" +10'-6" +11'-5" +8'-0" +8'-0" +8'-0" +8'-0" +8'-0" +8'-0" +8'-0" +8'-0" EQ EQ EQ EQ EQ 2' - 6"2' - 6" EQ EQ EQ EQ EQ F9 F9 F9 F9 EQ EQ F11 F11 F11 F11 F13 F11 F11 F11 F11 F5 F5 EX1 EX1 EX2 EQ EQ EQ EQ EQ EQ EQ EQ 5' - 0 " 16 A5.03 7' - 0" 16 A5.03 NOTE: (E) TRUSSES AND NEW CEILING AND ROOF FRAMING SHOWN FOR REFERENCE ONLY. REFER TO STRUCTURAL DRAWINGS FOR MORE DETAIL INFORMATION. ALL (E) CONDITIONS TO BE FIELD VERIFIED. EQ EQ EQ EQ 09-02 09-02 4' - 0 " 4' - 0 " 1' - 0" +8'-0" F2 08-09 TYP. 23-10 05-06 TYP. TYP. F14 EX2 EX1 UNDER CABINET LED LIGHT Scale Project number Date Drawn by Jen Dunbar, AIA phone: 310.435.3928 12314 La Maida Street Valley Village, CA 91607 jen@dunbararchitecture.com DUNBAR ARCHITECTURE JD/AP As indicated 4/ 7 / 2 0 2 5 9 : 2 1 : 3 3 P M A1.20 REFLECTED CEILING PLAN 23004 CYPRESS CENTER RESTORATION CITY OF SANTA ANA 1/17/2025 625 S. CYPRESS AVE. SANTA ANA, CA 92701 1/4" = 1'-0"A1.20 1 REFLECTED CEILING PLAN - PROPOSED 0'8'4'4' TYPE COUNT DESCRIPTION COMMENTS F1 5 LARGE SCHOOLHOUSE PENDANT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F2 13 INDUSTRIAL PENDANT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F3 24 SUSPENDED LINEAR PENDANT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F4 2 SURFACE MOUNTED EXTERIOR REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F5 4 SURFACE MOUNTED INTERIOR - 17" DIAM. REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F6 7 6" RECESSED CAN DOWNLIGHT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F7 1 SMALL SCHOOLHOUSE PENDANT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F8 8 2x2 PANEL LIGHT REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F9 12 EXTERIOR DECORATIVE SCONCE REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F10 7 EXTERIOR WALL LIGHTS REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F11 24 RECESSED 12" LINEAR REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F12 5 CEILING FAN, PENDANT MOUNTED REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F13 1 RECESSED 4" LINEAR REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS F14 1 SURFACE WALL MOUNTED REFER TO ELECTRICAL DRAWINGS AND CUT SHEETS FOR SELECTED PRODUCTS 05-06 LADDER ACCESS TO ROOF 06-03 1x6 SHEATHING ABOVE GYP WALL FINISH AT EAST AND SOUTH WALLS OF MULTI-PURPOSE RM A 08-09 30"x30" CEILING ACCESS PANEL 09-02 PATCH AND REPAIR PLASTER FINISH, ALL NEW MATERIALS SHALL MATCH ORIGINAL AS CLOSE AS POSSIBLE IN FINISH AND TEXTURE 23-10 DESIGN-BUILD MECHANICAL CATWALK REQUIRED FOR ACCESS TO ALL FAN COIL UNITS FROM CEILING ACCESS POINT; FIELD VERIFY LOCATION WITH (E) TRUSSES AND NEW CEILING FRAMING NOTE: REFER TO A0.00 FOR SITE LIGHTING FIXTURE SCHEDULE No. Description Date DESIGN DEVELOPMENT 1/12/2024 75% CD 3/15/2024 90% CD 5/14/2024 PERMIT SET 5/17/2024 OCFA SUBMITTAL 9/26/2024 BACKCHECK SET 1/17/2024 BACKCHECK SET_V2 4/8/2025